[OpenWrt-Devel] [PATCH] linux: add support of Synopsys ARCHS38-based boards

Alexey Brodkin Alexey.Brodkin at synopsys.com
Wed Dec 9 09:16:46 EST 2015


This patch introduces support of new boards with ARC HS38 cores.

ARC HS38 is a new generation of ARC cores which utilize ARCv2 ISA.
Because of new ISA ARC HS38 are binary incompatible with ARC 700
cores which requires both separate toolchain and target applications
including Linux kernel for that new cores.

As with ARC770 we're addind support for 2 boards for now:

 [1] Synopsys SDP board (AXS103)
     This is the same base-board as in AXS101 but with
     FPGA-based CPU-tile where ARCHs38 core is implemented.

 [2] nSIM
     Again this is the same simulation engine but configured for
     new instruction set and features of new CPU.

Cc: Felix Fietkau <nbd at openwrt.org>
Cc: Jo-Philipp Wich <jow at openwrt.org>
Cc: Jonas Gorski <jogo at openwrt.org>
Signed-off-by: Alexey Brodkin <abrodkin at synopsys.com>
---
 include/target.mk                                  |   1 +
 target/linux/archs38/Makefile                      |  27 +++
 target/linux/archs38/base-files.mk                 |   3 +
 .../archs38/base-files/etc/board.d/02_network      |  19 ++
 target/linux/archs38/base-files/lib/arc.sh         |  50 +++++
 .../base-files/lib/preinit/01_preinit_arc.sh       |   9 +
 target/linux/archs38/config-4.3                    | 190 +++++++++++++++++
 target/linux/archs38/dts/axc003_idu.dtsi           | 126 ++++++++++++
 target/linux/archs38/dts/axs103_idu.dts            |  25 +++
 target/linux/archs38/dts/axs10x_mb.dtsi            | 224 +++++++++++++++++++++
 target/linux/archs38/dts/nsim_hs_idu.dts           |  73 +++++++
 target/linux/archs38/dts/skeleton.dtsi             |  37 ++++
 .../linux/archs38/generic/profiles/00-default.mk   |  16 ++
 .../linux/archs38/generic/profiles/01-minimal.mk   |  15 ++
 target/linux/archs38/generic/profiles/02-axs103.mk |  16 ++
 .../linux/archs38/generic/profiles/03-nsim_hs.mk   |  15 ++
 target/linux/archs38/generic/target.mk             |   8 +
 target/linux/archs38/image/Makefile                |  40 ++++
 ...openwrt-arc-remove-dependency-on-DEVTMPFS.patch |  36 ++++
 .../0002-openwrt-arc-add-OWRTDTB-section.patch     |  91 +++++++++
 toolchain/gcc/common.mk                            |   1 +
 toolchain/uClibc/common.mk                         |   3 +-
 toolchain/uClibc/config/archs                      |  10 +
 23 files changed, 1034 insertions(+), 1 deletion(-)
 create mode 100644 target/linux/archs38/Makefile
 create mode 100644 target/linux/archs38/base-files.mk
 create mode 100755 target/linux/archs38/base-files/etc/board.d/02_network
 create mode 100644 target/linux/archs38/base-files/lib/arc.sh
 create mode 100644 target/linux/archs38/base-files/lib/preinit/01_preinit_arc.sh
 create mode 100644 target/linux/archs38/config-4.3
 create mode 100644 target/linux/archs38/dts/axc003_idu.dtsi
 create mode 100644 target/linux/archs38/dts/axs103_idu.dts
 create mode 100644 target/linux/archs38/dts/axs10x_mb.dtsi
 create mode 100644 target/linux/archs38/dts/nsim_hs_idu.dts
 create mode 100644 target/linux/archs38/dts/skeleton.dtsi
 create mode 100644 target/linux/archs38/generic/profiles/00-default.mk
 create mode 100644 target/linux/archs38/generic/profiles/01-minimal.mk
 create mode 100644 target/linux/archs38/generic/profiles/02-axs103.mk
 create mode 100644 target/linux/archs38/generic/profiles/03-nsim_hs.mk
 create mode 100644 target/linux/archs38/generic/target.mk
 create mode 100644 target/linux/archs38/image/Makefile
 create mode 100644 target/linux/archs38/patches-4.3/0001-openwrt-arc-remove-dependency-on-DEVTMPFS.patch
 create mode 100644 target/linux/archs38/patches-4.3/0002-openwrt-arc-add-OWRTDTB-section.patch
 create mode 100644 toolchain/uClibc/config/archs

diff --git a/include/target.mk b/include/target.mk
index f129298..009738a 100644
--- a/include/target.mk
+++ b/include/target.mk
@@ -264,6 +264,7 @@ ifeq ($(DUMP),1)
   ifeq ($(ARCH),arc)
     CPU_TYPE ?= arc700
     CPU_CFLAGS_arc700 = -marc700
+    CPU_CFLAGS_archs38 = -marchs
   endif
   DEFAULT_CFLAGS=$(strip $(CPU_CFLAGS) $(CPU_CFLAGS_$(CPU_TYPE)) $(CPU_CFLAGS_$(CPU_SUBTYPE)))
 endif
diff --git a/target/linux/archs38/Makefile b/target/linux/archs38/Makefile
new file mode 100644
index 0000000..855954a
--- /dev/null
+++ b/target/linux/archs38/Makefile
@@ -0,0 +1,27 @@
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+include $(TOPDIR)/rules.mk
+
+ARCH:=arc
+CPU_TYPE:=archs
+BOARD:=archs38
+BOARDNAME:=Synopsys DesignWare ARC HS38
+CFLAGS:=-Os -pipe -fno-caller-saves -matomic
+MAINTAINER:=Alexey Brodkin <abrodkin at synopsys.com>
+SUBTARGETS:=generic
+
+KERNEL_PATCHVER:=4.3
+
+DEVICE_TYPE:=developerboard
+
+include $(INCLUDE_DIR)/target.mk
+
+define Target/Description
+	Synopsys DesignWare boards
+endef
+
+$(eval $(call BuildTarget))
diff --git a/target/linux/archs38/base-files.mk b/target/linux/archs38/base-files.mk
new file mode 100644
index 0000000..fdd2c71
--- /dev/null
+++ b/target/linux/archs38/base-files.mk
@@ -0,0 +1,3 @@
+define Package/base-files/install-target
+	rm -f $(1)/etc/config/network
+endef
diff --git a/target/linux/archs38/base-files/etc/board.d/02_network b/target/linux/archs38/base-files/etc/board.d/02_network
new file mode 100755
index 0000000..cd5ad2d
--- /dev/null
+++ b/target/linux/archs38/base-files/etc/board.d/02_network
@@ -0,0 +1,19 @@
+#!/bin/sh
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+
+. /lib/arc.sh
+. /lib/functions/uci-defaults-new.sh
+
+board_config_update
+
+case "$( arc_board_name )" in
+"arc-sdp"*)
+	ucidef_set_interface_lan "eth0" "dhcp"
+	;;
+esac
+
+board_config_flush
+
+exit 0
diff --git a/target/linux/archs38/base-files/lib/arc.sh b/target/linux/archs38/base-files/lib/arc.sh
new file mode 100644
index 0000000..4ad162f
--- /dev/null
+++ b/target/linux/archs38/base-files/lib/arc.sh
@@ -0,0 +1,50 @@
+#!/bin/sh
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+
+# defaults
+ARC_BOARD_NAME="generic"
+ARC_BOARD_MODEL="Generic ARC board"
+
+arc_board_detect() {
+	local board
+	local model
+	local compatible
+
+	[ -e "/tmp/sysinfo/" ] || mkdir -p "/tmp/sysinfo/"
+
+	model="$( cat /proc/device-tree/model )"
+	compatible="$( cat /proc/device-tree/compatible )"
+
+	case "$compatible" in
+	"snps,axs103""snps,arc-sdp")
+		board="arc-sdp";
+		;;
+	"snps,nsim_hs")
+		board="arc-nsim";
+		;;
+	esac
+
+	if [ "$board" != "" ]; then
+		ARC_BOARD_NAME="$board"
+	fi
+
+	if [ "$model" != "" ]; then
+		ARC_BOARD_MODEL="$model"
+	fi
+
+	echo "$ARC_BOARD_NAME" > /tmp/sysinfo/board_name
+	echo "$ARC_BOARD_MODEL" > /tmp/sysinfo/model
+	echo "Detected $ARC_BOARD_NAME // $ARC_BOARD_MODEL"
+}
+
+arc_board_name() {
+	local name
+
+	[ -f /tmp/sysinfo/board_name ] && name="$(cat /tmp/sysinfo/board_name)"
+	[ -z "$name" ] && name="unknown"
+
+	echo "$name"
+}
+
diff --git a/target/linux/archs38/base-files/lib/preinit/01_preinit_arc.sh b/target/linux/archs38/base-files/lib/preinit/01_preinit_arc.sh
new file mode 100644
index 0000000..192c91b
--- /dev/null
+++ b/target/linux/archs38/base-files/lib/preinit/01_preinit_arc.sh
@@ -0,0 +1,9 @@
+#!/bin/sh
+
+do_arc() {
+        . /lib/arc.sh
+
+        arc_board_detect
+}
+
+boot_hook_add preinit_main do_arc
diff --git a/target/linux/archs38/config-4.3 b/target/linux/archs38/config-4.3
new file mode 100644
index 0000000..13a36b3
--- /dev/null
+++ b/target/linux/archs38/config-4.3
@@ -0,0 +1,190 @@
+# CONFIG_16KSTACKS is not set
+CONFIG_ARC=y
+CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
+# CONFIG_ARCH_HAS_GCOV_PROFILE_ALL is not set
+# CONFIG_ARCH_HAS_SG_CHAIN is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
+CONFIG_ARC_BUILTIN_DTB_NAME=""
+CONFIG_ARC_CACHE=y
+CONFIG_ARC_CACHE_LINE_SHIFT=6
+CONFIG_ARC_CACHE_PAGES=y
+# CONFIG_ARC_CANT_LLSC is not set
+CONFIG_ARC_CPU_HS=y
+CONFIG_ARC_CURR_IN_REG=y
+CONFIG_ARC_DBG=y
+# CONFIG_ARC_DBG_TLB_MISS_COUNT is not set
+# CONFIG_ARC_DBG_TLB_PARANOIA is not set
+CONFIG_ARC_DW2_UNWIND=y
+CONFIG_ARC_HAS_COH_CACHES=y
+CONFIG_ARC_HAS_DCACHE=y
+# CONFIG_ARC_HAS_DCCM is not set
+CONFIG_ARC_HAS_DIV_REM=y
+CONFIG_ARC_HAS_GRTC=y
+CONFIG_ARC_HAS_HW_MPY=y
+CONFIG_ARC_HAS_ICACHE=y
+# CONFIG_ARC_HAS_ICCM is not set
+CONFIG_ARC_HAS_LL64=y
+CONFIG_ARC_HAS_LLSC=y
+# CONFIG_ARC_HAS_REENTRANT_IRQ_LV2 is not set
+CONFIG_ARC_HAS_SWAPE=y
+# CONFIG_ARC_IPI_DBG is not set
+CONFIG_ARC_MCIP=y
+# CONFIG_ARC_METAWARE_HLINK is not set
+# CONFIG_ARC_MMU_V1 is not set
+# CONFIG_ARC_MMU_V2 is not set
+CONFIG_ARC_MMU_V4=y
+CONFIG_ARC_NUMBER_OF_INTERRUPTS=32
+# CONFIG_ARC_PAGE_SIZE_16K is not set
+# CONFIG_ARC_PAGE_SIZE_4K is not set
+CONFIG_ARC_PAGE_SIZE_8K=y
+CONFIG_ARC_PLAT_AXS10X=y
+CONFIG_ARC_PLAT_SIM=y
+# CONFIG_ARC_PLAT_TB10X is not set
+CONFIG_ARC_STAR_9000923308=y
+# CONFIG_ARC_UBOOT_SUPPORT is not set
+CONFIG_AXS103=y
+CONFIG_CLKDEV_LOOKUP=y
+CONFIG_CLONE_BACKWARDS=y
+CONFIG_COMMON_CLK=y
+# CONFIG_CPU_BIG_ENDIAN is not set
+CONFIG_CPU_RMAP=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_WORKQUEUE=y
+CONFIG_DTC=y
+CONFIG_DWMAC_GENERIC=y
+# CONFIG_DWMAC_IPQ806X is not set
+# CONFIG_DWMAC_LPC18XX is not set
+# CONFIG_DWMAC_MESON is not set
+# CONFIG_DWMAC_ROCKCHIP is not set
+# CONFIG_DWMAC_SOCFPGA is not set
+# CONFIG_DWMAC_STI is not set
+# CONFIG_DWMAC_SUNXI is not set
+CONFIG_DW_APB_ICTL=y
+CONFIG_GENERIC_ATOMIC64=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CSUM=y
+CONFIG_GENERIC_FIND_FIRST_BIT=y
+CONFIG_GENERIC_IO=y
+CONFIG_GENERIC_IRQ_CHIP=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_PENDING_IRQ=y
+CONFIG_GENERIC_SMP_IDLE_THREAD=y
+# CONFIG_GEN_RTC is not set
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_DEVRES=y
+CONFIG_GPIO_DWAPB=y
+CONFIG_GPIO_GENERIC=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
+# CONFIG_HAVE_ARCH_BITREVERSE is not set
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_HAVE_ARCH_TRACEHOOK=y
+# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
+CONFIG_HAVE_CLK=y
+CONFIG_HAVE_CLK_PREPARE=y
+CONFIG_HAVE_DEBUG_STACKOVERFLOW=y
+CONFIG_HAVE_FUTEX_CMPXCHG=y
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
+CONFIG_HAVE_IOREMAP_PROT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_HAVE_MEMBLOCK=y
+CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
+CONFIG_HAVE_NET_DSA=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_HZ_PERIODIC=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_IRQCHIP=y
+CONFIG_IRQ_DOMAIN=y
+CONFIG_IRQ_WORK=y
+# CONFIG_ISA_ARCOMPACT is not set
+CONFIG_ISA_ARCV2=y
+CONFIG_KALLSYMS=y
+CONFIG_LIBFDT=y
+CONFIG_LINUX_LINK_BASE=0x80000000
+CONFIG_LOCK_SPIN_ON_OWNER=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_MDIO_BOARDINFO=y
+CONFIG_MFD_SYSCON=y
+CONFIG_MMC=y
+CONFIG_MMC_DW=y
+# CONFIG_MMC_DW_EXYNOS is not set
+CONFIG_MMC_DW_IDMAC=y
+# CONFIG_MMC_DW_K3 is not set
+CONFIG_MMC_DW_PLTFM=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MODULES_USE_ELF_RELA=y
+CONFIG_MUTEX_SPIN_ON_OWNER=y
+CONFIG_NATIONAL_PHY=y
+# CONFIG_NET_CADENCE is not set
+CONFIG_NET_FLOW_LIMIT=y
+CONFIG_NET_PTP_CLASSIFY=y
+# CONFIG_NET_VENDOR_ARC is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_QUALCOMM is not set
+# CONFIG_NET_VENDOR_ROCKER is not set
+# CONFIG_NET_VENDOR_SAMSUNG is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_NO_BOOTMEM=y
+CONFIG_NO_IOPORT_MAP=y
+CONFIG_NR_CPUS=4
+CONFIG_OF=y
+CONFIG_OF_ADDRESS=y
+CONFIG_OF_EARLY_FLATTREE=y
+CONFIG_OF_FLATTREE=y
+CONFIG_OF_GPIO=y
+CONFIG_OF_IRQ=y
+CONFIG_OF_MDIO=y
+CONFIG_OF_MTD=y
+CONFIG_OF_NET=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PGTABLE_LEVELS=2
+CONFIG_PHYLIB=y
+CONFIG_PPS=y
+CONFIG_PREEMPT=y
+CONFIG_PREEMPT_COUNT=y
+# CONFIG_PREEMPT_NONE is not set
+CONFIG_PREEMPT_RCU=y
+CONFIG_PTP_1588_CLOCK=y
+# CONFIG_RCU_BOOST is not set
+CONFIG_RCU_STALL_COMMON=y
+CONFIG_REGMAP=y
+CONFIG_REGMAP_MMIO=y
+CONFIG_RESET_CONTROLLER=y
+CONFIG_RFS_ACCEL=y
+CONFIG_RPS=y
+# CONFIG_RTC is not set
+# CONFIG_SCHED_INFO is not set
+# CONFIG_SCSI_DMA is not set
+CONFIG_SERIAL_8250_DEPRECATED_OPTIONS=y
+CONFIG_SERIAL_8250_DW=y
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_ARC=y
+CONFIG_SERIAL_ARC_CONSOLE=y
+CONFIG_SERIAL_ARC_NR_PORTS=1
+CONFIG_SERIAL_OF_PLATFORM=y
+# CONFIG_SG_SPLIT is not set
+CONFIG_SMP=y
+CONFIG_SRCU=y
+CONFIG_STACKTRACE=y
+CONFIG_STMMAC_ETH=y
+CONFIG_STMMAC_PLATFORM=y
+CONFIG_STOP_MACHINE=y
+# CONFIG_SUNXI_SRAM is not set
+CONFIG_TICK_CPU_ACCOUNTING=y
+CONFIG_UNINLINE_SPIN_UNLOCK=y
+CONFIG_USB_SUPPORT=y
+CONFIG_XPS=y
+CONFIG_ZONE_DMA_FLAG=0
diff --git a/target/linux/archs38/dts/axc003_idu.dtsi b/target/linux/archs38/dts/axc003_idu.dtsi
new file mode 100644
index 0000000..2f0b332
--- /dev/null
+++ b/target/linux/archs38/dts/axc003_idu.dtsi
@@ -0,0 +1,126 @@
+/*
+ * Copyright (C) 2014, 2015 Synopsys, Inc. (www.synopsys.com)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * Device tree for AXC003 CPU card: HS38x2 (Dual Core) with IDU intc
+ */
+
+/ {
+	compatible = "snps,arc";
+	clock-frequency = <90000000>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpu_card {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		ranges = <0x00000000 0xf0000000 0x10000000>;
+
+		cpu_intc: archs-intc at cpu {
+			compatible = "snps,archs-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		idu_intc: idu-interrupt-controller {
+			compatible = "snps,archs-idu-intc";
+			interrupt-controller;
+			interrupt-parent = <&cpu_intc>;
+
+			/*
+			 * <hwirq  distribution>
+			 * distribution: 0=RR; 1=cpu0, 2=cpu1, 4=cpu2, 8=cpu3
+			 */
+			#interrupt-cells = <2>;
+
+			/*
+			 * upstream irqs to core intc - downstream these are
+			 * "COMMON" irq 0,1..
+			 */
+			interrupts = <24 25>;
+		};
+
+		/*
+		 * this GPIO block ORs all interrupts on CPU card (creg,..)
+		 * to uplink only 1 IRQ to ARC core intc
+		 */
+		dw-apb-gpio at 0x2000 {
+			compatible = "snps,dw-apb-gpio";
+			reg = < 0x2000 0x80 >;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ictl_intc: gpio-controller at 0 {
+				compatible = "snps,dw-apb-gpio-port";
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <30>;
+				reg = <0>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupt-parent = <&idu_intc>;
+
+				/*
+				 * cmn irq 1 -> cpu irq 25
+				 * Distribute to cpu0 only
+				 */
+				interrupts = <1 1>;
+			};
+		};
+
+		debug_uart: dw-apb-uart at 0x5000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x5000 0x100>;
+			clock-frequency = <33333000>;
+			interrupt-parent = <&ictl_intc>;
+			interrupts = <2 4>;
+			baud = <115200>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+		};
+
+		arcpct0: pct {
+			compatible = "snps,archs-pct";
+			#interrupt-cells = <1>;
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <20>;
+		};
+	};
+
+	/*
+	 * This INTC is actually connected to DW APB GPIO
+	 * which acts as a wire between MB INTC and CPU INTC.
+	 * GPIO INTC is configured in platform init code
+	 * and here we mimic direct connection from MB INTC to
+	 * CPU INTC, thus we set "interrupts = <0 1>" instead of
+	 * "interrupts = <12>"
+	 *
+	 * This intc actually resides on MB, but we move it here to
+	 * avoid duplicating the MB dtsi file given that IRQ from
+	 * this intc to cpu intc are different for axs101 and axs103
+	 */
+	mb_intc: dw-apb-ictl at 0xe0012000 {
+		#interrupt-cells = <1>;
+		compatible = "snps,dw-apb-ictl";
+		reg = < 0xe0012000 0x200 >;
+		interrupt-controller;
+		interrupt-parent = <&idu_intc>;
+		interrupts = <0 1>;	/* cmn irq 0 -> cpu irq 24
+					   distribute to cpu0 only */
+	};
+
+	memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00000000 0x80000000 0x40000000>;
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;	/* 512MiB */
+	};
+};
diff --git a/target/linux/archs38/dts/axs103_idu.dts b/target/linux/archs38/dts/axs103_idu.dts
new file mode 100644
index 0000000..66cedac
--- /dev/null
+++ b/target/linux/archs38/dts/axs103_idu.dts
@@ -0,0 +1,25 @@
+/*
+ * Copyright (C) 2014-15 Synopsys, Inc. (www.synopsys.com)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * Device Tree for AXS103 SDP with AXS10X Main Board and
+ * AXC003 FPGA Card (with SMP bitfile)
+ */
+/dts-v1/;
+
+/include/ "axc003_idu.dtsi"
+/include/ "axs10x_mb.dtsi"
+
+/ {
+	model = "Synopsys AXS103 Development Board";
+	compatible = "snps,axs103", "snps,arc-sdp";
+
+	chosen {
+		bootargs = "earlycon=uart8250,mmio32,0xe0022000,115200n8 console=ttyS3,115200n8 debug print-fatal-signals=1";
+	};
+};
diff --git a/target/linux/archs38/dts/axs10x_mb.dtsi b/target/linux/archs38/dts/axs10x_mb.dtsi
new file mode 100644
index 0000000..f3db321
--- /dev/null
+++ b/target/linux/archs38/dts/axs10x_mb.dtsi
@@ -0,0 +1,224 @@
+/*
+ * Support for peripherals on the AXS10x mainboard
+ *
+ * Copyright (C) 2013-15 Synopsys, Inc. (www.synopsys.com)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/ {
+	axs10x_mb {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00000000 0xe0000000 0x10000000>;
+		interrupt-parent = <&mb_intc>;
+
+		clocks {
+			i2cclk: i2cclk {
+				compatible = "fixed-clock";
+				clock-frequency = <50000000>;
+				#clock-cells = <0>;
+			};
+
+			apbclk: apbclk {
+				compatible = "fixed-clock";
+				clock-frequency = <50000000>;
+				#clock-cells = <0>;
+			};
+
+			mmcclk: mmcclk {
+				compatible = "fixed-clock";
+				clock-frequency = <50000000>;
+				#clock-cells = <0>;
+			};
+		};
+
+		ethernet at 0x18000 {
+			#interrupt-cells = <1>;
+			compatible = "snps,dwmac";
+			reg = < 0x18000 0x2000 >;
+			interrupts = < 4 >;
+			interrupt-names = "macirq";
+			phy-mode = "rgmii";
+			snps,pbl = < 32 >;
+			clocks = <&apbclk>;
+			clock-names = "stmmaceth";
+		};
+
+		ehci at 0x40000 {
+			compatible = "generic-ehci";
+			reg = < 0x40000 0x100 >;
+			interrupts = < 8 >;
+		};
+
+		ohci at 0x60000 {
+			compatible = "generic-ohci";
+			reg = < 0x60000 0x100 >;
+			interrupts = < 8 >;
+		};
+
+		/*
+		 * According to DW Mobile Storage databook it is required
+		 * to use  "Hold Register" if card is enumerated in SDR12 or
+		 * SDR25 modes.
+		 *
+		 * Utilization of "Hold Register" is already implemented via
+		 * dw_mci_pltfm_prepare_command() which in its turn gets
+		 * used through dw_mci_drv_data->prepare_command call-back.
+		 * This call-back is used in Altera Socfpga platform and so
+		 * we may reuse it saying that we're compatible with their
+		 * "altr,socfpga-dw-mshc".
+		 *
+		 * Most probably "Hold Register" utilization is platform-
+		 * independent requirement which means that single unified
+		 * "snps,dw-mshc" should be enough for all users of DW MMC once
+		 * dw_mci_pltfm_prepare_command() is used in generic platform
+		 * code.
+		 */
+		mmc at 0x15000 {
+			compatible = "altr,socfpga-dw-mshc";
+			reg = < 0x15000 0x400 >;
+			num-slots = < 1 >;
+			fifo-depth = < 16 >;
+			card-detect-delay = < 200 >;
+			clocks = <&apbclk>, <&mmcclk>;
+			clock-names = "biu", "ciu";
+			interrupts = < 7 >;
+			bus-width = < 4 >;
+		};
+
+		uart at 0x20000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x20000 0x100>;
+			clock-frequency = <33333333>;
+			interrupts = <17>;
+			baud = <115200>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+		};
+
+		uart at 0x21000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x21000 0x100>;
+			clock-frequency = <33333333>;
+			interrupts = <18>;
+			baud = <115200>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+		};
+
+		/* UART muxed with USB data port (ttyS3) */
+		uart at 0x22000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x22000 0x100>;
+			clock-frequency = <33333333>;
+			interrupts = <19>;
+			baud = <115200>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+		};
+
+		i2c at 0x1d000 {
+			compatible = "snps,designware-i2c";
+			reg = <0x1d000 0x100>;
+			clock-frequency = <400000>;
+			clocks = <&i2cclk>;
+			interrupts = <14>;
+		};
+
+		i2c at 0x1e000 {
+			compatible = "snps,designware-i2c";
+			reg = <0x1e000 0x100>;
+			clock-frequency = <400000>;
+			clocks = <&i2cclk>;
+			interrupts = <15>;
+		};
+
+		i2c at 0x1f000 {
+			compatible = "snps,designware-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1f000 0x100>;
+			clock-frequency = <400000>;
+			clocks = <&i2cclk>;
+			interrupts = <16>;
+
+			eeprom at 0x54{
+				compatible = "24c01";
+				reg = <0x54>;
+				pagesize = <0x8>;
+			};
+
+			eeprom at 0x57{
+				compatible = "24c04";
+				reg = <0x57>;
+				pagesize = <0x8>;
+			};
+		};
+
+		gpio0:gpio at 13000 {
+			compatible = "snps,dw-apb-gpio";
+			reg = <0x13000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpio0_banka: gpio-controller at 0 {
+				compatible = "snps,dw-apb-gpio-port";
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <32>;
+				reg = <0>;
+			};
+
+			gpio0_bankb: gpio-controller at 1 {
+				compatible = "snps,dw-apb-gpio-port";
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <8>;
+				reg = <1>;
+			};
+
+			gpio0_bankc: gpio-controller at 2 {
+				compatible = "snps,dw-apb-gpio-port";
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <8>;
+				reg = <2>;
+			};
+		};
+
+		gpio1:gpio at 14000 {
+			compatible = "snps,dw-apb-gpio";
+			reg = <0x14000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpio1_banka: gpio-controller at 0 {
+				compatible = "snps,dw-apb-gpio-port";
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <30>;
+				reg = <0>;
+			};
+
+			gpio1_bankb: gpio-controller at 1 {
+				compatible = "snps,dw-apb-gpio-port";
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <10>;
+				reg = <1>;
+			};
+
+			gpio1_bankc: gpio-controller at 2 {
+				compatible = "snps,dw-apb-gpio-port";
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <8>;
+				reg = <2>;
+			};
+		};
+	};
+};
diff --git a/target/linux/archs38/dts/nsim_hs_idu.dts b/target/linux/archs38/dts/nsim_hs_idu.dts
new file mode 100644
index 0000000..75f539b
--- /dev/null
+++ b/target/linux/archs38/dts/nsim_hs_idu.dts
@@ -0,0 +1,73 @@
+/*
+ * Copyright (C) 2014-15 Synopsys, Inc. (www.synopsys.com)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+/include/ "skeleton.dtsi"
+
+/ {
+	model = "Synopsys ARC HS38 nSIM simulator";
+	compatible = "snps,nsim_hs";
+	interrupt-parent = <&core_intc>;
+
+	chosen {
+		bootargs = "earlycon=arc_uart,mmio32,0xc0fc1000,115200n8 console=ttyARC0,115200n8";
+	};
+
+	aliases {
+		serial0 = &arcuart0;
+	};
+
+	fpga {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* child and parent address space 1:1 mapped */
+		ranges;
+
+		core_intc: core-interrupt-controller {
+			compatible = "snps,archs-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		idu_intc: idu-interrupt-controller {
+			compatible = "snps,archs-idu-intc";
+			interrupt-controller;
+			interrupt-parent = <&core_intc>;
+
+			/*
+			 * <hwirq  distribution>
+			 * distribution: 0=RR; 1=cpu0, 2=cpu1, 4=cpu2, 8=cpu3
+			 */
+			#interrupt-cells = <2>;
+
+			/*
+			 * upstream irqs to core intc - downstream these are
+			 * "COMMON" irq 0,1..
+			 */
+			interrupts = <24 25 26 27 28 29 30 31>;
+		};
+
+		arcuart0: serial at c0fc1000 {
+			compatible = "snps,arc-uart";
+			reg = <0xc0fc1000 0x100>;
+			interrupt-parent = <&idu_intc>;
+			interrupts = <0 0>;
+			clock-frequency = <80000000>;
+			current-speed = <115200>;
+			status = "okay";
+		};
+
+		arcpct0: pct {
+			compatible = "snps,archs-pct";
+			#interrupt-cells = <1>;
+			interrupts = <20>;
+		};
+	};
+};
diff --git a/target/linux/archs38/dts/skeleton.dtsi b/target/linux/archs38/dts/skeleton.dtsi
new file mode 100644
index 0000000..a870bdd
--- /dev/null
+++ b/target/linux/archs38/dts/skeleton.dtsi
@@ -0,0 +1,37 @@
+/*
+ * Copyright (C) 2012 Synopsys, Inc. (www.synopsys.com)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * Skeleton device tree; the bare minimum needed to boot; just include and
+ * add a compatible value.
+ */
+
+/ {
+	compatible = "snps,arc";
+	clock-frequency = <80000000>;	/* 80 MHZ */
+	#address-cells = <1>;
+	#size-cells = <1>;
+	chosen { };
+	aliases { };
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu at 0 {
+			device_type = "cpu";
+			compatible = "snps,arc770d";
+			reg = <0>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;	/* 256M */
+	};
+};
diff --git a/target/linux/archs38/generic/profiles/00-default.mk b/target/linux/archs38/generic/profiles/00-default.mk
new file mode 100644
index 0000000..b12ceb1
--- /dev/null
+++ b/target/linux/archs38/generic/profiles/00-default.mk
@@ -0,0 +1,16 @@
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/Default
+	NAME:=Default Profile (all drivers)
+	PACKAGES:= kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-mmc kmod-sdhci
+endef
+
+define Profile/Default/Description
+	Default package set compatible with most boards.
+endef
+$(eval $(call Profile,Default))
diff --git a/target/linux/archs38/generic/profiles/01-minimal.mk b/target/linux/archs38/generic/profiles/01-minimal.mk
new file mode 100644
index 0000000..c8968da
--- /dev/null
+++ b/target/linux/archs38/generic/profiles/01-minimal.mk
@@ -0,0 +1,15 @@
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/Minimal
+	NAME:=Minimal Profile (no drivers)
+endef
+
+define Profile/Minimal/Description
+	Minimal package set compatible with most boards.
+endef
+$(eval $(call Profile,Minimal))
diff --git a/target/linux/archs38/generic/profiles/02-axs103.mk b/target/linux/archs38/generic/profiles/02-axs103.mk
new file mode 100644
index 0000000..19cf0c0
--- /dev/null
+++ b/target/linux/archs38/generic/profiles/02-axs103.mk
@@ -0,0 +1,16 @@
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/axs103
+	NAME:=Synopsys DesignWare AXS103
+	PACKAGES:= kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-mmc kmod-sdhci
+endef
+
+define Profile/axs103/Description
+	Package set compatible with hardware using Synopsys DesignWare AXS103 boards.
+endef
+$(eval $(call Profile,axs103))
diff --git a/target/linux/archs38/generic/profiles/03-nsim_hs.mk b/target/linux/archs38/generic/profiles/03-nsim_hs.mk
new file mode 100644
index 0000000..20f5d70
--- /dev/null
+++ b/target/linux/archs38/generic/profiles/03-nsim_hs.mk
@@ -0,0 +1,15 @@
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/nsim_hs
+	NAME:=Synopsys nSIM
+endef
+
+define Profile/nsim_hs/Description
+	Package set compatible with hardware using Synopsys nSIM HS boards.
+endef
+$(eval $(call Profile,nsim_hs))
diff --git a/target/linux/archs38/generic/target.mk b/target/linux/archs38/generic/target.mk
new file mode 100644
index 0000000..19b310e
--- /dev/null
+++ b/target/linux/archs38/generic/target.mk
@@ -0,0 +1,8 @@
+BOARDNAME:=Generic
+FEATURES += ramdisk usb
+
+define Target/Description
+	Build firmware images for generic ARC HS38 based boards.
+endef
+
+
diff --git a/target/linux/archs38/image/Makefile b/target/linux/archs38/image/Makefile
new file mode 100644
index 0000000..ef72c00
--- /dev/null
+++ b/target/linux/archs38/image/Makefile
@@ -0,0 +1,40 @@
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+include $(TOPDIR)/rules.mk
+include $(INCLUDE_DIR)/image.mk
+
+define Build/patch-dtb
+	$(call Image/BuildDTB,../dts/$(DEVICE_DTS).dts,$@.dtb)
+	$(STAGING_DIR_HOST)/bin/patch-dtb $@ $@.dtb
+endef
+
+# Shared device definition: applies to every defined device
+define Device/Default
+  PROFILES = Default $$(DEVICE_PROFILE)
+  KERNEL_SUFFIX := .elf
+  KERNEL_INITRAMFS := kernel-bin | patch-dtb
+  KERNEL_INITRAMFS_NAME = $$(KERNEL_NAME)-initramfs.elf
+  DEVICE_PROFILE :=
+  DEVICE_DTS :=
+endef
+DEVICE_VARS += DEVICE_PROFILE DEVICE_DTS
+
+define add_archs38
+  define Device/$(1)
+    DEVICE_PROFILE := $(1)
+    DEVICE_DTS := $(1)
+  endef
+  TARGET_DEVICES += $(1)
+endef
+
+# DesignWare AXS103
+$(eval $(call add_archs38,axs103_idu))
+
+# nSIM with ARCHS38
+$(eval $(call add_archs38,nsim_hs_idu))
+
+$(eval $(call BuildImage))
diff --git a/target/linux/archs38/patches-4.3/0001-openwrt-arc-remove-dependency-on-DEVTMPFS.patch b/target/linux/archs38/patches-4.3/0001-openwrt-arc-remove-dependency-on-DEVTMPFS.patch
new file mode 100644
index 0000000..53f8074
--- /dev/null
+++ b/target/linux/archs38/patches-4.3/0001-openwrt-arc-remove-dependency-on-DEVTMPFS.patch
@@ -0,0 +1,36 @@
+From 271777096a31e76b2ffd750bc44efde9656de857 Mon Sep 17 00:00:00 2001
+From: Alexey Brodkin <abrodkin at synopsys.com>
+Date: Thu, 13 Aug 2015 01:56:02 +0300
+Subject: [PATCH] openwrt: arc - remove dependency on DEVTMPFS
+
+OpenWRT builds initramfs so that it doesn't require DEVTMPFS so dropping
+this dependency. That helps to escape 2 separate kernel rebuilds with
+and without initramfs.
+
+2 builds happen because OpenWRT first builds kernel and later modules.
+When building entire kernel with simple "make" INITRAMFS sets to a real
+value and so was triggering DEVTMPFS selection. Then when building only
+modules with "make modules" command INITRAMFS is zeroed and so kernel
+config was changing that lead to full kernel rebuild.
+
+Signed-off-by: Alexey Brodkin <abrodkin at synopsys.com>
+---
+ arch/arc/Kconfig | 2 --
+ 1 file changed, 2 deletions(-)
+
+diff --git a/arch/arc/Kconfig b/arch/arc/Kconfig
+index cf96ef2..f0c6d4c 100644
+--- a/arch/arc/Kconfig
++++ b/arch/arc/Kconfig
+@@ -11,8 +11,6 @@ config ARC
+ 	select BUILDTIME_EXTABLE_SORT
+ 	select COMMON_CLK
+ 	select CLONE_BACKWARDS
+-	# ARC Busybox based initramfs absolutely relies on DEVTMPFS for /dev
+-	select DEVTMPFS if !INITRAMFS_SOURCE=""
+ 	select GENERIC_ATOMIC64
+ 	select GENERIC_CLOCKEVENTS
+ 	select GENERIC_FIND_FIRST_BIT
+-- 
+2.4.3
+
diff --git a/target/linux/archs38/patches-4.3/0002-openwrt-arc-add-OWRTDTB-section.patch b/target/linux/archs38/patches-4.3/0002-openwrt-arc-add-OWRTDTB-section.patch
new file mode 100644
index 0000000..ddb426f
--- /dev/null
+++ b/target/linux/archs38/patches-4.3/0002-openwrt-arc-add-OWRTDTB-section.patch
@@ -0,0 +1,91 @@
+From 142abc9f7b8860638e39cf3850cf7ba328c26b42 Mon Sep 17 00:00:00 2001
+From: Alexey Brodkin <abrodkin at synopsys.com>
+Date: Sat, 31 Oct 2015 15:58:20 +0300
+Subject: [PATCH] openwrt: arc - add OWRTDTB section
+
+This change allows OpenWRT to patch resulting kernel binary with
+external .dtb.
+
+That allows us to re-use exactky the same vmlinux on different boards
+given its ARC core configurations match (at least cache line sizes etc).
+
+""patch-dtb" searches for ASCII "OWRTDTB:" strign and copies external
+.dtb right after it, keeping the string in place.
+
+Signed-off-by: Alexey Brodkin <abrodkin at synopsys.com>
+---
+ arch/arc/kernel/head.S        | 10 ++++++++++
+ arch/arc/kernel/setup.c       |  4 +++-
+ arch/arc/kernel/vmlinux.lds.S | 13 +++++++++++++
+ 3 files changed, 26 insertions(+), 1 deletion(-)
+
+diff --git a/arch/arc/kernel/head.S b/arch/arc/kernel/head.S
+index 689dd86..51154ae 100644
+--- a/arch/arc/kernel/head.S
++++ b/arch/arc/kernel/head.S
+@@ -49,6 +49,16 @@
+ 1:
+ .endm
+ 
++; Here "patch-dtb" will embed external .dtb
++; Note "patch-dtb" searches for ASCII "OWRTDTB:" string
++; and pastes .dtb right after it, hense the string precedes
++; __image_dtb symbol.
++	.section .owrt, "aw", at progbits
++	.ascii	"OWRTDTB:"
++ENTRY(__image_dtb)
++	.fill	0x4000
++END(__image_dtb)
++
+ 	.section .init.text, "ax", at progbits
+ 
+ ;----------------------------------------------------------------
+diff --git a/arch/arc/kernel/setup.c b/arch/arc/kernel/setup.c
+index c33e77c..96fbfd0 100644
+--- a/arch/arc/kernel/setup.c
++++ b/arch/arc/kernel/setup.c
+@@ -370,6 +370,8 @@ static inline int is_kernel(unsigned long addr)
+ 	return 0;
+ }
+ 
++extern struct boot_param_header __image_dtb;
++
+ void __init setup_arch(char **cmdline_p)
+ {
+ #ifdef CONFIG_ARC_UBOOT_SUPPORT
+@@ -383,7 +385,7 @@ void __init setup_arch(char **cmdline_p)
+ #endif
+ 	{
+ 		/* No, so try the embedded one */
+-		machine_desc = setup_machine_fdt(__dtb_start);
++		machine_desc = setup_machine_fdt(&__image_dtb);
+ 		if (!machine_desc)
+ 			panic("Embedded DT invalid\n");
+ 
+diff --git a/arch/arc/kernel/vmlinux.lds.S b/arch/arc/kernel/vmlinux.lds.S
+index dd35bde..f309104 100644
+--- a/arch/arc/kernel/vmlinux.lds.S
++++ b/arch/arc/kernel/vmlinux.lds.S
+@@ -30,6 +30,19 @@ SECTIONS
+ 
+ 	. = CONFIG_LINUX_LINK_BASE;
+ 
++	/*
++	 * In OpenWRT we want to patch built binary embedding .dtb of choice.
++	 * This is implemented with "patch-dtb" utility which searches for
++	 * "OWRTDTB:" string in first 16k of image and if it is found
++	 * copies .dtb right after mentioned string.
++	 *
++	 * Note: "OWRTDTB:" won't be overwritten with .dtb, .dtb will follow it.
++	 */
++	.owrt : {
++		*(.owrt)
++		. = ALIGN(PAGE_SIZE);
++	}
++
+ 	_int_vec_base_lds = .;
+ 	.vector : {
+ 		*(.vector)
+-- 
+2.4.3
+
diff --git a/toolchain/gcc/common.mk b/toolchain/gcc/common.mk
index 3e4f3ee..4566f4d 100644
--- a/toolchain/gcc/common.mk
+++ b/toolchain/gcc/common.mk
@@ -143,6 +143,7 @@ GCC_CONFIGURE:= \
 		$(call qstrip,$(CONFIG_EXTRA_GCC_CONFIG_OPTIONS)) \
 		$(if $(CONFIG_mips64)$(CONFIG_mips64el),--with-arch=mips64 \
 			--with-abi=$(call qstrip,$(CONFIG_MIPS64_ABI))) \
+		$(if $(CONFIG_arc),--with-cpu=$(CONFIG_CPU_TYPE)) \
 		--with-gmp=$(TOPDIR)/staging_dir/host \
 		--with-mpfr=$(TOPDIR)/staging_dir/host \
 		--with-mpc=$(TOPDIR)/staging_dir/host \
diff --git a/toolchain/uClibc/common.mk b/toolchain/uClibc/common.mk
index ad6ff02..2828156 100644
--- a/toolchain/uClibc/common.mk
+++ b/toolchain/uClibc/common.mk
@@ -41,8 +41,9 @@ GEN_CONFIG=$(SCRIPT_DIR)/kconfig.pl -n \
 	$(if $(CONFIG_UCLIBC_ENABLE_DEBUG),$(if $(wildcard $(CONFIG_DIR)/debug),'+' $(CONFIG_DIR)/debug)) \
 	$(CONFIG_DIR)/$(ARCH)$(strip \
 		$(if $(wildcard $(CONFIG_DIR)/$(ARCH).$(BOARD)),.$(BOARD), \
+			$(if $(filter archs,$(subst ",,$(CONFIG_CPU_TYPE))),hs, \
 			$(if $(CONFIG_MIPS64_ABI),.$(subst ",,$(CONFIG_MIPS64_ABI)), \
-			$(if $(CONFIG_HAS_SPE_FPU),$(if $(wildcard $(CONFIG_DIR)/$(ARCH).e500),.e500)))))
+			$(if $(CONFIG_HAS_SPE_FPU),$(if $(wildcard $(CONFIG_DIR)/$(ARCH).e500),.e500))))))
 
 CPU_CFLAGS = \
 	-funsigned-char -fno-builtin -fno-asm \
diff --git a/toolchain/uClibc/config/archs b/toolchain/uClibc/config/archs
new file mode 100644
index 0000000..961628e
--- /dev/null
+++ b/toolchain/uClibc/config/archs
@@ -0,0 +1,10 @@
+ARCH_ANY_ENDIAN=y
+ARCH_LITTLE_ENDIAN=y
+ARCH_WANTS_LITTLE_ENDIAN=y
+TARGET_ARCH="arc"
+TARGET_arc=y
+# CONFIG_ARC_CPU_700 is not set
+CONFIG_ARC_CPU_HS=y
+CONFIG_ARC_PAGE_SIZE_8K=y
+# CONFIG_ARC_PAGE_SIZE_16K is not set
+# CONFIG_ARC_PAGE_SIZE_4K is not set
-- 
2.5.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list