[OpenWrt-Devel] [PATCH] Added WIZnet WizFi630A Platform based on Ralink RT5350
Tobias Welz
tw at wiznet.eu
Mon Aug 17 16:47:48 EDT 2015
From: Tobias Welz <tw at wiznet.eu>
Signed-off-by: Tobias Welz <tw at wiznet.eu>
---
.../linux/ramips/base-files/etc/board.d/02_network | 5 +
target/linux/ramips/base-files/etc/diag.sh | 3 +
target/linux/ramips/base-files/lib/ramips.sh | 3 +
.../ramips/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ramips/dts/WIZFI630A.dts | 294
++++++++++++++++++++
target/linux/ramips/image/Makefile | 4 +-
target/linux/ramips/rt305x/profiles/wizfi630a.mk | 18 ++
7 files changed, 327 insertions(+), 1 deletion(-)
create mode 100644 target/linux/ramips/dts/WIZFI630A.dts
create mode 100644 target/linux/ramips/rt305x/profiles/wizfi630a.mk
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
b/target/linux/ramips/base-files/etc/board.d/02_network
index 6a2f042..cfd0b26 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -217,6 +217,7 @@ ramips_setup_interfaces()
ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 6t"
ucidef_add_switch_vlan "switch0" "2" "5 6t"
;;
+ wizfi630a | \
y1s)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
@@ -320,6 +321,10 @@ ramips_setup_macs()
wcr-150gn)
wan_mac=$(mtd_get_mac_binary factory 40)
;;
+ wizfi630a)
+ lan_mac=$(mtd_get_mac_binary factory 4)
+ wan_mac=$(mtd_get_mac_binary factory 40)
+ ;;
whr-1166d|\
whr-300hp2|\
whr-600d|\
diff --git a/target/linux/ramips/base-files/etc/diag.sh
b/target/linux/ramips/base-files/etc/diag.sh
index a4911b0..54b84e5 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -143,6 +143,9 @@ get_status_led() {
whr-600d)
status_led="$board:orange:wifi"
;;
+ wizfi630a)
+ status_led="wizfi630a::run"
+ ;;
rt-n10-plus|\
tew-691gr|\
tew-692gr|\
diff --git a/target/linux/ramips/base-files/lib/ramips.sh
b/target/linux/ramips/base-files/lib/ramips.sh
index 5cafd45..b6d1023 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -367,6 +367,9 @@ ramips_board_detect() {
*"WIZARD 8800")
name="wizard8800"
;;
+ *"WIZnet WizFi630A")
+ name="wizfi630a"
+ ;;
*"WL-330N")
name="wl-330n"
;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh
b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index 53e7070..947a328 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -107,6 +107,7 @@ platform_check_image() {
whr-300hp2|\
whr-600d|\
whr-g300n|\
+ wizfi630a |\
wl-330n|\
wl-330n3g|\
wl-341v3|\
diff --git a/target/linux/ramips/dts/WIZFI630A.dts
b/target/linux/ramips/dts/WIZFI630A.dts
new file mode 100644
index 0000000..0d44c71
--- /dev/null
+++ b/target/linux/ramips/dts/WIZFI630A.dts
@@ -0,0 +1,294 @@
+/dts-v1/;
+
+/include/ "rt5350.dtsi"
+
+/ {
+ compatible = "wizfi630a", "ralink,rt5350-soc";
+ model = "WIZnet WizFi630A";
+
+ chosen {
+ bootargs = "console=ttyS1,115200";
+ };
+
+ palmbus at 10000000 {
+ gpio1: gpio at 660 {
+ status = "okay";
+ };
+
+ spi at b00 {
+ status = "okay";
+
+ m25p80 at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "w25q128";
+ reg = <0>;
+ linux,modalias = "m25p80", "w25q128";
+ spi-max-frequency = <10000000>;
+
+ partition at 0 {
+ label = "uboot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "uboot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition at 40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition at 50000 {
+ label = "firmware";
+ reg = <0x50000 0xfb0000>;
+ };
+ };
+ };
+
+ uart at 500 {
+ compatible = "ralink,mt7620a-uart", "ralink,rt2880-uart", "ns16550a";
+ reg = <0x500 0x100>;
+
+ resets = <&rstctrl 12>;
+ reset-names = "uart";
+
+ interrupt-parent = <&intc>;
+ interrupts = <5>;
+
+ reg-shift = <2>;
+
+ status = "okay";
+ };
+
+
+ uartlite at c00 {
+ compatible = "ralink,mt7620a-uart", "ralink,rt2880-uart", "ns16550a";
+ reg = <0xc00 0x100>;
+
+ resets = <&rstctrl 19>;
+ reset-names = "uartl";
+
+ interrupt-parent = <&intc>;
+ interrupts = <12>;
+
+ reg-shift = <2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&uartlite_pins>;
+ };
+ };
+
+ pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ ralink,group = "i2c", "jtag" ;
+ ralink,function = "gpio";
+ };
+ };
+
+ uartf_gpio_pins: uartf_gpio {
+ uartf_gpio {
+ ralink,group = "uartf";
+ ralink,function = "uartf";
+ };
+ };
+
+ uartlite_pins: uartlite {
+ uart {
+ ralink,group = "uartlite";
+ ralink,function = "uartlite";
+ };
+ };
+ };
+
+ ethernet at 10100000 {
+ mtd-mac-address = <&factory 0x4>;
+ };
+
+ esw at 10110000 {
+ ralink,portmap = <0x17>;
+ };
+
+ wmac at 10180000 {
+ ralink,mtd-eeprom = <&factory 0>;
+ };
+
+ ehci at 101c0000 {
+ status = "okay";
+ };
+
+ ohci at 101c1000 {
+ status = "okay";
+ };
+
+ gpio-export {
+ compatible = "gpio-export";
+ #size-cells = <0>;
+/*
+ gpio22 {
+ // WAN + gpio-export,name = "gpio22";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio1 0 0>; // path lfd dir
+ };
+ gpio23 {
+ // LAN1 + gpio-export,name = "gpio23";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio1 1 0>;
+ };
+ gpio24 {
+ // LAN2 + gpio-export,name = "gpio24";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio1 2 0>;
+ };
+
+ // UARTF - UART1 + gpio7 {
+ // UARTF_RTS_N - HW Pin 6
+ gpio-export,name = "gpio7";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 7 0>;
+ };
+ gpio8 {
+ // UARTF_TXD - HW Pin 10 + gpio-export,name = "gpio8";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 8 0>;
+ };
+ gpio9 {
+ // UARTF_CTS_N - HW Pin 5
+ gpio-export,name = "gpio9";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 9 0>;
+ };
+ gpio10 {
+ // UARTF_RXD - HW Pin 9
+ gpio-export,name = "gpio10";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 10 0>;
+ };
+ gpio11 {
+ // UARTF_DTR_N - HW Pin 8
+ gpio-export,name = "gpio11";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 11 0>;
+ };
+ gpio12 {
+ // UARTF_DCD_N - HW Pin 12 + gpio-export,name = "gpio12";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 12 0>;
+ };
+ gpio13 {
+ // UARTF_DSR_N - HW Pin 11
+ gpio-export,name = "gpio13";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 13 0>;
+ };
+ gpio14 {
+ // UARTF_RIN - HW Pin 7 + gpio-export,name = "gpio14";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 14 0>;
+ };
+
+ // UARTLITE - UART2 + gpio15 {
+ // UART2_TXD - HW Pin 20 + gpio-export,name = "gpio15";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 15 0>;
+ };
+ gpio16 {
+ // UART2_RXD - HW Pin 18 + gpio-export,name = "gpio16";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 16 0>;
+ };
+
+*/
+/*
+ // If you want to use this comment out the corrosponding gpio-keys-polled
+ gpio0 {
+ // wps btn
+ gpio-export,name = "gpio0";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 0 1>;
+ };
+*/
+
+ gpio19 {
+ // SCM1
+ gpio-export,name = "gpio19";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 19 1>;
+ };
+ gpio2 {
+ // SCM2
+ gpio-export,name = "gpio2";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 2 1>;
+ };
+
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ run {
+ label = "wizfi630a::run";
+ gpios = <&gpio0 1 1>;
+ };
+ uart1 {
+ label = "wizfi630a::uart1";
+ gpios = <&gpio0 18 1>;
+ };
+ uart2 {
+ label = "wizfi630a::uart2";
+ gpios = <&gpio0 21 1>;
+ };
+ wps {
+ label = "wizfi630a::wps";
+ gpios = <&gpio0 20 1>;
+ };
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+ reset {
+ label = "reset";
+ gpios = <&gpio0 17 1>;
+ linux,code = <0x198>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&gpio0 0 1>;
+ linux,code = <0x211>;
+ };
+/*
+ // If you want to use this comment out the corrosponding export
+ scm1 {
+ label = "SCM1";
+ gpios = <&gpio0 19 1>;
+ linux,code = <0x100>;
+ };
+
+ scm2 {
+ label = "SCM2";
+ gpios = <&gpio0 2 1>;
+ linux,code = <0x101>;
+ };
+*/
+ };
+};
diff --git a/target/linux/ramips/image/Makefile
b/target/linux/ramips/image/Makefile
index 2f4d4cb..ac2e83c 100644
--- a/target/linux/ramips/image/Makefile
+++ b/target/linux/ramips/image/Makefile
@@ -608,7 +608,6 @@ Image/Build/Profile/W502U=$(call
BuildFirmware/Default8M/$(1),$(1),w502u,W502U)
Image/Build/Profile/WCR150GN=$(call
BuildFirmware/Default4M/$(1),$(1),wcr150gn,WCR150GN)
-
Image/Build/Profile/MZK-DP150N=$(call
BuildFirmware/Default4M/$(1),$(1),mzk-dp150n,MZK-DP150N)
buffalo_whrg300n_mtd_size=3801088
@@ -631,6 +630,8 @@ Image/Build/Profile/WHRG300N=$(call
BuildFirmware/WHRG300N/$(1),$(1))
Image/Build/Profile/WIZARD8800=$(call
BuildFirmware/Default8M/$(1),$(1),wizard-8800,WIZARD8800,Linux Kernel Image)
+Image/Build/Profile/WIZFI630A=$(call
BuildFirmware/Default16M/$(1),$(1),wizfi630a,WIZFI630A)
+
Image/Build/Profile/WL-330N=$(call
BuildFirmware/Default4M/$(1),$(1),wl-330n,WL-330N)
Image/Build/Profile/WL-330N3G=$(call
BuildFirmware/Default4M/$(1),$(1),wl-330n3g,WL-330N3G)
@@ -763,6 +764,7 @@ define Image/Build/Profile/Default
$(call Image/Build/Profile/WCR150GN,$(1))
$(call Image/Build/Profile/WHRG300N,$(1))
$(call Image/Build/Profile/WIZARD8800,$(1))
+ $(call Image/Build/Profile/WIZFI630A,$(1))
$(call Image/Build/Profile/WL-330N,$(1))
$(call Image/Build/Profile/WL-330N3G,$(1))
$(call Image/Build/Profile/WL-341V3,$(1))
diff --git a/target/linux/ramips/rt305x/profiles/wizfi630a.mk
b/target/linux/ramips/rt305x/profiles/wizfi630a.mk
new file mode 100644
index 0000000..2d2c001
--- /dev/null
+++ b/target/linux/ramips/rt305x/profiles/wizfi630a.mk
@@ -0,0 +1,18 @@
+#
+# Copyright (C) 2014 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/WIZFI630A
+ NAME:=WIZnet WizFi630A
+ PACKAGES:=\
+ kmod-usb2 +endef
+
+define Profile/WIZFI630A/Description
+ Package set for WIZnet WizFi630A board
+endef
+
+$(eval $(call Profile,WIZFI630A))
--
1.7.10.4
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list