[OpenWrt-Devel] [PATCH v2] ramips: add support for Planex DB-WRT01
Piotr Dymacz
pepe2k at gmail.com
Mon Aug 17 14:13:50 EDT 2015
Hello,
Please, see my comments inline.
2015-08-17 19:20 GMT+02:00 YuheiOKAWA <tochiro.srchack at gmail.com>:
> This patch add support for Planex DB-WRT01. DANBOARD route on
> the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
> DANBOARD is Cartoon character.
>
> Signed-off-by: YuheiOKAWA <tochiro.srchack at gmail.com>
> ---
> target/linux/ramips/base-files/etc/board.d/01_leds | 3 +
> .../linux/ramips/base-files/etc/board.d/02_network | 1 +
> target/linux/ramips/base-files/etc/diag.sh | 1 +
> target/linux/ramips/base-files/lib/ramips.sh | 3 +
> .../ramips/base-files/lib/upgrade/platform.sh | 1 +
> target/linux/ramips/dts/DB-WRT01.dts | 99 ++++++++++++++++++++++
> target/linux/ramips/image/Makefile | 2 +
> 7 files changed, 110 insertions(+)
> create mode 100644 target/linux/ramips/dts/DB-WRT01.dts
>
> diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
> index 71cf3ac..a9959e3 100755
> --- a/target/linux/ramips/base-files/etc/board.d/01_leds
> +++ b/target/linux/ramips/base-files/etc/board.d/01_leds
> @@ -87,6 +87,9 @@ d105)
> ucidef_set_led_default "power" "POWER" "$board:red:power" "1"
> set_usb_led "$board:green:usb"
> ;;
> +db-wrt01)
> + ucidef_set_led_default "power" "power" "$board:orange:power" "1"
> + ;;
> dcs-930l-b1)
> ucidef_set_led_default "power" "POWER" "$board:red:power" "1"
> ucidef_set_led_netdev "wifi" "WiFi" "$board:blue:wps"
> diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
> index 6a2f042..02cd682 100755
> --- a/target/linux/ramips/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/base-files/etc/board.d/02_network
> @@ -61,6 +61,7 @@ ramips_setup_interfaces()
> ;;
> 3g-6200n|\
> ai-br100|\
> + db-wrt01|\
> dir-300-b7|\
> dir-320-b1|\
> dir-610-a1|\
> diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
> index a4911b0..f886b5d 100644
> --- a/target/linux/ramips/base-files/etc/diag.sh
> +++ b/target/linux/ramips/base-files/etc/diag.sh
> @@ -94,6 +94,7 @@ get_status_led() {
> y1s)
> status_led="$board:blue:power"
> ;;
> + db-wrt01|\
> esr-9753)
> status_led="$board:orange:power"
> ;;
> diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
> index 5cafd45..5b6808e 100755
> --- a/target/linux/ramips/base-files/lib/ramips.sh
> +++ b/target/linux/ramips/base-files/lib/ramips.sh
> @@ -97,6 +97,9 @@ ramips_board_detect() {
> *"DAP-1350")
> name="dap-1350"
> ;;
> + *"DB-WRT01")
> + name="db-wrt01"
> + ;;
> *"DCS-930")
> name="dcs-930"
> ;;
> diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> index 53e7070..844ed5d 100755
> --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> @@ -36,6 +36,7 @@ platform_check_image() {
> cf-wr800n|\
> d105|\
> dap-1350|\
> + db-wrt01|\
> dcs-930|\
> dcs-930l-b1|\
> dir-300-b1|\
> diff --git a/target/linux/ramips/dts/DB-WRT01.dts b/target/linux/ramips/dts/DB-WRT01.dts
> new file mode 100644
> index 0000000..a8953e9
> --- /dev/null
> +++ b/target/linux/ramips/dts/DB-WRT01.dts
> @@ -0,0 +1,99 @@
> +/dts-v1/;
> +
> +/include/ "mt7620a.dtsi"
> +
> +/ {
> + compatible = "ralink,mt7620a-soc";
> + model = "Planex DB-WRT01";
> +
> + palmbus at 10000000 {
> + gpio1: gpio at 638 {
> + status = "okay";
> + };
> +
> + spi at b00 {
> + status = "okay";
> +
> + m25p80 at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "en25q64";
> + reg = <0 0>;
> + linux,modalias = "m25p80", "mx25l6405d";
> + spi-max-frequency = <10000000>;
> +
> + partition at 0 {
> + label = "u-boot";
> + reg = <0x0 0x30000>;
> + read-only;
> + };
> +
> + partition at 30000 {
> + label = "u-boot-env";
> + reg = <0x30000 0x10000>;
> + read-only;
> + };
> +
> + factory: partition at 40000 {
> + label = "factory";
> + reg = <0x40000 0x10000>;
> + read-only;
> + };
> +
> + partition at 50000 {
> + label = "firmware";
> + reg = <0x50000 0x7b0000>;
> + };
> + };
> + };
> + };
> +
> + pinctrl {
> + state_default: pinctrl0 {
> + gpio {
> + ralink,group = "i2c", "spi refclk", "rgmii1";
> + ralink,function = "gpio";
> + };
> + };
> + };
> +
> + ethernet at 10100000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&ephy_pins>;
> +
Is this empty line really needed here?
> + mtd-mac-address = <&factory 0x4>;
> + ralink,port-map = "llllw";
> + };
> +
> + gsw at 10110000 {
> + ralink,port4 = "ephy";
> + };
> +
> + wmac at 10180000 {
> + ralink,mtd-eeprom = <&factory 0>;
> + };
> +
> + pcie at 10140000 {
> + status = "okay";
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
Empty line here, please.
> + power {
> + label = "db-wrt01:orange:power";
> + gpios = <&gpio1 1 1>;
> + };
> + };
> +
> + gpio-keys-polled {
> + compatible = "gpio-keys-polled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + poll-interval = <20>;
And here too.
> + s1 {
> + label = "wps";
> + gpios = <&gpio0 2 1>;
> + linux,code = <0x211>;
> + };
> + };
> +};
> diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile
> index 2f4d4cb..4632ad2 100644
> --- a/target/linux/ramips/image/Makefile
> +++ b/target/linux/ramips/image/Makefile
> @@ -868,6 +868,7 @@ Image/Build/Profile/CF-WR800N=$(call BuildFirmware/Default8M/$(1),$(1),cf-wr800n
> Image/Build/Profile/DIR-810L=$(call BuildFirmware/CustomFlash/$(1),$(1),dir-810l,DIR-810L,$(dlink810l_mtd_size))
> na930_mtd_size=20971520
> Image/Build/Profile/NA930=$(call BuildFirmware/CustomFlash/$(1),$(1),na930,NA930,$(na930_mtd_size))
> +Image/Build/Profile/DB-WRT01=$(call BuildFirmware/Default8M/$(1),$(1),db-wrt01,DB-WRT01)
> Image/Build/Profile/MZK-750DHP=$(call BuildFirmware/Default8M/$(1),$(1),mzk-750dhp,MZK-750DHP)
> Image/Build/Profile/OY-0001=$(call BuildFirmware/Default16M/$(1),$(1),oy-0001,OY-0001)
> Image/Build/Profile/Y1=$(call BuildFirmware/Default16M/$(1),$(1),y1,Y1)
> @@ -901,6 +902,7 @@ define Image/Build/Profile/Default
> $(call Image/Build/Profile/WHR300HP2,$(1))
> $(call Image/Build/Profile/WHR600D,$(1))
> $(call Image/Build/Profile/WHR1166D,$(1))
> + $(call Image/Build/Profile/DB-WRT01,$(1))
> $(call Image/Build/Profile/MZK-750DHP,$(1))
> $(call Image/Build/Profile/NA930,$(1))
> $(call Image/Build/Profile/OY-0001,$(1))
> --
> 1.9.1
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list