[PATCH] Added WIZnet WizFi630A Platform based on Ralink RT5350
Tobias Welz
aclass="moz-txt-link-rfc2396E"href="mailto:tw at wiznet.eu"
Fri Aug 14 20:30:34 EDT 2015
Signed-off-by: Tobias Welz <a class="moz-txt-link-rfc2396E" href="mailto:tw at wiznet.eu"><tw at wiznet.eu></a>
---
.../linux/ramips/base-files/etc/board.d/02_network | 6 +
target/linux/ramips/base-files/etc/diag.sh | 3 +
target/linux/ramips/base-files/lib/ramips.sh | 3 +
.../ramips/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ramips/dts/WIZFI630A.dts | 304
++++++++++++++++++++
target/linux/ramips/image/Makefile | 3 +
target/linux/ramips/rt305x/profiles/wizfi630a.mk | 18 ++
7 files changed, 338 insertions(+)
create mode 100644 target/linux/ramips/dts/WIZFI630A.dts
create mode 100644 target/linux/ramips/rt305x/profiles/wizfi630a.mk
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
b/target/linux/ramips/base-files/etc/board.d/02_network
index da1854a..c211ab9 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -235,6 +235,7 @@ ramips_setup_interfaces()
ucidef_add_switch_vlan "switch0" "2" "4 6t"
;;
+ wizfi630a | \
y1s)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "switch0" "1" "1"
@@ -297,6 +298,11 @@ ramips_setup_macs()
wan_mac=$(mtd_get_mac_binary factory 46)
;;
+ wizfi630a)
+ lan_mac=$(mtd_get_mac_binary factory 4)
+ wan_mac=$(mtd_get_mac_binary factory 40)
+ ;;
+
w306r-v20)
lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(macaddr_add "$lan_mac" 5)
diff --git a/target/linux/ramips/base-files/etc/diag.sh
b/target/linux/ramips/base-files/etc/diag.sh
index e63f0df..3ffcc22 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -252,6 +252,9 @@ get_status_led() {
zte-q7)
status_led="zte:red:status"
;;
+ wizfi630a)
+ status_led="wizfi630a::run"
+ ;;
mzk-dp150n)
status_led="mzkdp150n:green:power"
;;
diff --git a/target/linux/ramips/base-files/lib/ramips.sh
b/target/linux/ramips/base-files/lib/ramips.sh
index 7db6d37..474fdb8 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -430,6 +430,9 @@ ramips_board_detect() {
*"Planex MZK-DP150N")
name="mzk-dp150n"
;;
+ *"WIZnet WizFi630A")
+ name="wizfi630a"
+ ;;
*)
name="generic"
;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh
b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index 8221997..bdc6be9 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -105,6 +105,7 @@ platform_check_image() {
whr-300hp2 |\
whr-600d |\
whr-1166d |\
+ wizfi630a |\
wsr-600 |\
wl-330n | \
wl-330n3g | \
diff --git a/target/linux/ramips/dts/WIZFI630A.dts
b/target/linux/ramips/dts/WIZFI630A.dts
new file mode 100644
index 0000000..b3f655d
--- /dev/null
+++ b/target/linux/ramips/dts/WIZFI630A.dts
@@ -0,0 +1,304 @@
+/dts-v1/;
+
+/include/ "rt5350.dtsi"
+
+/ {
+ compatible = "wizfi630a", "ralink,rt5350-soc";
+ model = "WIZnet WizFi630A";
+
+ chosen {
+ bootargs = "console=ttyS1,115200";
+ };
+
+ palmbus at 10000000 {
+ gpio1: gpio at 660 {
+ status = "okay";
+ };
+
+ spi at b00 {
+ status = "okay";
+
+ m25p80 at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "w25q128";
+ reg = <0>;
+ linux,modalias = "m25p80", "w25q128";
+ spi-max-frequency = <10000000>;
+
+ partition at 0 {
+ label = "uboot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "uboot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition at 40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition at 50000 {
+ label = "firmware";
+ reg = <0x50000 0xfb0000>;
+ };
+ };
+ };
+
+ uart at 500 {
+ compatible = "ralink,mt7620a-uart",
"ralink,rt2880-uart", "ns16550a";
+ reg = <0x500 0x100>;
+
+ resets = <&rstctrl 12>;
+ reset-names = "uart";
+
+ interrupt-parent = <&intc>;
+ interrupts = <5>;
+
+ reg-shift = <2>;
+
+ status = "okay";
+ };
+
+
+ uartlite at c00 {
+ compatible = "ralink,mt7620a-uart",
"ralink,rt2880-uart", "ns16550a";
+ reg = <0xc00 0x100>;
+
+ resets = <&rstctrl 19>;
+ reset-names = "uartl";
+
+ interrupt-parent = <&intc>;
+ interrupts = <12>;
+
+ reg-shift = <2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&uartlite_pins>;
+ };
+ };
+
+ pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ ralink,group = "i2c", "jtag" ;
+ ralink,function = "gpio";
+ };
+ };
+
+ uartf_gpio_pins: uartf_gpio {
+ uartf_gpio {
+ ralink,group = "uartf";
+ //ralink,function = "gpio uartf";
+ ralink,function = "uartf";
+ };
+ };
+
+ uartlite_pins: uartlite {
+ uart {
+ ralink,group = "uartlite";
+ ralink,function = "uartlite";
+ };
+ };
+ };
+
+ ethernet at 10100000 {
+ mtd-mac-address = <&factory 0x4>;
+ };
+
+ esw at 10110000 {
+ ralink,portmap = <0x17>;
+ };
+
+ wmac at 10180000 {
+ ralink,mtd-eeprom = <&factory 0>;
+ };
+
+ ehci at 101c0000 {
+ status = "okay";
+ };
+
+ ohci at 101c1000 {
+ status = "okay";
+ };
+
+
+ gpio-export {
+ compatible = "gpio-export";
+ #size-cells = <0>;
+/*
+ gpio22 {
+ // WAN
+ gpio-export,name = "gpio22";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio1 0 0>; // path lfd dir
+ };
+ gpio23 {
+ // LAN1
+ gpio-export,name = "gpio23";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio1 1 0>;
+ };
+ gpio24 {
+ // LAN2
+ gpio-export,name = "gpio24";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio1 2 0>;
+ };
+
+ // UARTF - UART1
+ gpio7 {
+ // UARTF_RTS_N - HW Pin 6
+ gpio-export,name = "gpio7";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 7 0>;
+ };
+ gpio8 {
+ // UARTF_TXD - HW Pin 10
+ gpio-export,name = "gpio8";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 8 0>;
+ };
+ gpio9 {
+ // UARTF_CTS_N - HW Pin 5
+ gpio-export,name = "gpio9";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 9 0>;
+ };
+ gpio10 {
+ // UARTF_RXD - HW Pin 9
+ gpio-export,name = "gpio10";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 10 0>;
+ };
+ gpio11 {
+ // UARTF_DTR_N - HW Pin 8
+ gpio-export,name = "gpio11";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 11 0>;
+ };
+ gpio12 {
+ // UARTF_DCD_N - HW Pin 12
+ gpio-export,name = "gpio12";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 12 0>;
+ };
+ gpio13 {
+ // UARTF_DSR_N - HW Pin 11
+ gpio-export,name = "gpio13";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 13 0>;
+ };
+ gpio14 {
+ // UARTF_RIN - HW Pin 7
+ gpio-export,name = "gpio14";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 14 0>;
+ };
+
+ // UARTLITE - UART2
+ gpio15 {
+ // UART2_TXD - HW Pin 20
+ gpio-export,name = "gpio15";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 15 0>;
+ };
+ gpio16 {
+ // UART2_RXD - HW Pin 18
+ gpio-export,name = "gpio16";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 16 0>;
+ };
+
+*/
+/*
+ // If you want to use this comment out the corrosponding
gpio-keys-polled
+ gpio0 {
+ // wps btn
+ gpio-export,name = "gpio0";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 0 1>;
+ };
+*/
+
+ gpio19 {
+ // SCM1
+ gpio-export,name = "gpio19";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 19 1>;
+ };
+ gpio2 {
+ // SCM2
+ gpio-export,name = "gpio2";
+ gpio-export,direction_may_change = <1>;
+ gpios = <&gpio0 2 1>;
+ };
+
+ };
+
+
+
+
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ run {
+ label = "wizfi630a::run";
+ gpios = <&gpio0 1 1>;
+ };
+ uart1 {
+ label = "wizfi630a::uart1";
+ gpios = <&gpio0 18 1>;
+ };
+ uart2 {
+ label = "wizfi630a::uart2";
+ gpios = <&gpio0 21 1>;
+ };
+ wps {
+ label = "wizfi630a::wps";
+ gpios = <&gpio0 20 1>;
+ };
+ };
+
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+ reset {
+ label = "reset";
+ gpios = <&gpio0 17 1>;
+ linux,code = <0x198>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&gpio0 0 1>;
+ linux,code = <0x211>;
+ };
+/*
+ // If you want to use this comment out the corrosponding export
+ scm1 {
+ label = "SCM1";
+ gpios = <&gpio0 19 1>;
+ linux,code = <0x100>;
+ };
+
+ scm2 {
+ label = "SCM2";
+ gpios = <&gpio0 2 1>;
+ linux,code = <0x101>;
+ };
+*/
+
+ };
+
+
+};
diff --git a/target/linux/ramips/image/Makefile
b/target/linux/ramips/image/Makefile
index 409ff26..fbc6775 100644
--- a/target/linux/ramips/image/Makefile
+++ b/target/linux/ramips/image/Makefile
@@ -673,6 +673,8 @@ Image/Build/Profile/WNCE2001=$(call
BuildFirmware/WNCE2001/$(1),$(1),wnce2001,WN
Image/Build/Profile/WR512-3GN=$(call
BuildFirmware/DefaultDualSize/$(1),$(1),wr512-3ng,WR512-3GN)
+Image/Build/Profile/WIZFI630A=$(call
BuildFirmware/Default16M/$(1),$(1),wizfi630a,WIZFI630A)
+
Image/Build/Profile/WT1520=$(call
BuildFirmware/PorayDualSize/$(1),$(1),wt1520,WT1520)
Image/Build/Profile/UR-326N4G=$(call
BuildFirmware/Default4M/$(1),$(1),ur-326n4g,UR-326N4G)
@@ -761,6 +763,7 @@ define Image/Build/Profile/Default
$(call Image/Build/Profile/W306R_V20,$(1))
$(call Image/Build/Profile/W502U,$(1))
$(call Image/Build/Profile/WCR150GN,$(1))
+ $(call Image/Build/Profile/WIZFI630A,$(1))
$(call Image/Build/Profile/WHRG300N,$(1))
$(call Image/Build/Profile/WIZARD8800,$(1))
$(call Image/Build/Profile/WL_330N,$(1))
diff --git a/target/linux/ramips/rt305x/profiles/wizfi630a.mk
b/target/linux/ramips/rt305x/profiles/wizfi630a.mk
new file mode 100644
index 0000000..22136b9
--- /dev/null
+++ b/target/linux/ramips/rt305x/profiles/wizfi630a.mk
@@ -0,0 +1,18 @@
+#
+# Copyright (C) 2014 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/WIZFI630A
+ NAME:=WIZnet WizFi630A
+ PACKAGES:=\
+ kmod-usb-core kmod-usb-ohci kmod-usb2
+endef
+
+define Profile/WIZFI630A/Description
+ Package set for WIZnet WizFi630A board
+endef
+
+$(eval $(call Profile,WIZFI630A))
--
1.7.10.4
_______________________________________________
openwrt-devel mailing list
<a class="moz-txt-link-abbreviated" href="mailto:openwrt-devel at lists.openwrt.org">openwrt-devel at lists.openwrt.org</a>
<a class="moz-txt-link-freetext" href="https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel">https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel</a>
</pre>
</blockquote>
<pre wrap="">_______________________________________________
openwrt-devel mailing list
<a class="moz-txt-link-abbreviated" href="mailto:openwrt-devel at lists.openwrt.org">openwrt-devel at lists.openwrt.org</a>
<a class="moz-txt-link-freetext" href="https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel">https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel</a>
</pre>
</blockquote>
</blockquote>
<br>
<div style="bottom: auto; left: 580px; right: auto; top: 102px;
display: none;" class="translator-theme-default"
id="translator-floating-panel">
<div title="Zum übersetzen klicken"
id="translator-floating-panel-button"></div>
</div>
</body>
</html>
--------------010001090206080106000807--
--===============6867360452628219917==
Content-Type: text/plain; charset="us-ascii"
MIME-Version: 1.0
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
--===============6867360452628219917==--
More information about the openwrt-devel
mailing list