[OpenWrt-Devel] [PATCH] Added WIZnet WizFi630A Platform based on Ralink RT5350
John Crispin
blogic at openwrt.org
Mon Aug 17 07:24:34 EDT 2015
Hi Tobias,
Thanks for the patch. unfortunately its line mangled and white space
broken. also it seems you sent a HTML email. If you take a few minutes
to setup git, you can use "git send-email" to avoid these issues.
John
On 15/08/2015 10:08, Tobias Welz wrote:
> Hello OpenWrt Developers,
>
> I added the WIZnet WizFi630A Platform to the trunk. The board is based
> on Ralink RT5350 in MiniPci Express Form Factor.
>
> Kind regards
> Tobias Welz
>
>
>
> From bd69bb513e36abda43e86f0eb64caf004260e415 Mon Sep 17 00:00:00 2001
> From: Tobias Welz <tw at wiznet.eu>
> Date: Sat, 15 Aug 2015 02:30:34 +0200
> Subject: [PATCH] Added WIZnet WizFi630A Platform based on Ralink RT5350
>
>
> Signed-off-by: Tobias Welz <tw at wiznet.eu>
> ---
> .../linux/ramips/base-files/etc/board.d/02_network | 6 +
> target/linux/ramips/base-files/etc/diag.sh | 3 +
> target/linux/ramips/base-files/lib/ramips.sh | 3 +
> .../ramips/base-files/lib/upgrade/platform.sh | 1 +
> target/linux/ramips/dts/WIZFI630A.dts | 304
> ++++++++++++++++++++
> target/linux/ramips/image/Makefile | 3 +
> target/linux/ramips/rt305x/profiles/wizfi630a.mk | 18 ++
> 7 files changed, 338 insertions(+)
> create mode 100644 target/linux/ramips/dts/WIZFI630A.dts
> create mode 100644 target/linux/ramips/rt305x/profiles/wizfi630a.mk
>
> diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
> b/target/linux/ramips/base-files/etc/board.d/02_network
> index da1854a..c211ab9 100755
> --- a/target/linux/ramips/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/base-files/etc/board.d/02_network
> @@ -235,6 +235,7 @@ ramips_setup_interfaces()
> ucidef_add_switch_vlan "switch0" "2" "4 6t"
> ;;
>
> + wizfi630a | \
> y1s)
> ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
> ucidef_add_switch "switch0" "1" "1"
> @@ -297,6 +298,11 @@ ramips_setup_macs()
> wan_mac=$(mtd_get_mac_binary factory 46)
> ;;
>
> + wizfi630a)
> + lan_mac=$(mtd_get_mac_binary factory 4)
> + wan_mac=$(mtd_get_mac_binary factory 40)
> + ;;
> +
> w306r-v20)
> lan_mac=$(cat /sys/class/net/eth0/address)
> wan_mac=$(macaddr_add "$lan_mac" 5)
> diff --git a/target/linux/ramips/base-files/etc/diag.sh
> b/target/linux/ramips/base-files/etc/diag.sh
> index e63f0df..3ffcc22 100644
> --- a/target/linux/ramips/base-files/etc/diag.sh
> +++ b/target/linux/ramips/base-files/etc/diag.sh
> @@ -252,6 +252,9 @@ get_status_led() {
> zte-q7)
> status_led="zte:red:status"
> ;;
> + wizfi630a)
> + status_led="wizfi630a::run"
> + ;;
> mzk-dp150n)
> status_led="mzkdp150n:green:power"
> ;;
> diff --git a/target/linux/ramips/base-files/lib/ramips.sh
> b/target/linux/ramips/base-files/lib/ramips.sh
> index 7db6d37..474fdb8 100755
> --- a/target/linux/ramips/base-files/lib/ramips.sh
> +++ b/target/linux/ramips/base-files/lib/ramips.sh
> @@ -430,6 +430,9 @@ ramips_board_detect() {
> *"Planex MZK-DP150N")
> name="mzk-dp150n"
> ;;
> + *"WIZnet WizFi630A")
> + name="wizfi630a"
> + ;;
> *)
> name="generic"
> ;;
> diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> index 8221997..bdc6be9 100755
> --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> @@ -105,6 +105,7 @@ platform_check_image() {
> whr-300hp2 |\
> whr-600d |\
> whr-1166d |\
> + wizfi630a |\
> wsr-600 |\
> wl-330n | \
> wl-330n3g | \
> diff --git a/target/linux/ramips/dts/WIZFI630A.dts
> b/target/linux/ramips/dts/WIZFI630A.dts
> new file mode 100644
> index 0000000..b3f655d
> --- /dev/null
> +++ b/target/linux/ramips/dts/WIZFI630A.dts
> @@ -0,0 +1,304 @@
> +/dts-v1/;
> +
> +/include/ "rt5350.dtsi"
> +
> +/ {
> + compatible = "wizfi630a", "ralink,rt5350-soc";
> + model = "WIZnet WizFi630A";
> +
> + chosen {
> + bootargs = "console=ttyS1,115200";
> + };
> +
> + palmbus at 10000000 {
> + gpio1: gpio at 660 {
> + status = "okay";
> + };
> +
> + spi at b00 {
> + status = "okay";
> +
> + m25p80 at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "w25q128";
> + reg = <0>;
> + linux,modalias = "m25p80", "w25q128";
> + spi-max-frequency = <10000000>;
> +
> + partition at 0 {
> + label = "uboot";
> + reg = <0x0 0x30000>;
> + read-only;
> + };
> +
> + partition at 30000 {
> + label = "uboot-env";
> + reg = <0x30000 0x10000>;
> + read-only;
> + };
> +
> + factory: partition at 40000 {
> + label = "factory";
> + reg = <0x40000 0x10000>;
> + read-only;
> + };
> +
> + partition at 50000 {
> + label = "firmware";
> + reg = <0x50000 0xfb0000>;
> + };
> + };
> + };
> +
> + uart at 500 {
> + compatible = "ralink,mt7620a-uart",
> "ralink,rt2880-uart", "ns16550a";
> + reg = <0x500 0x100>;
> +
> + resets = <&rstctrl 12>;
> + reset-names = "uart";
> +
> + interrupt-parent = <&intc>;
> + interrupts = <5>;
> +
> + reg-shift = <2>;
> +
> + status = "okay";
> + };
> +
> +
> + uartlite at c00 {
> + compatible = "ralink,mt7620a-uart",
> "ralink,rt2880-uart", "ns16550a";
> + reg = <0xc00 0x100>;
> +
> + resets = <&rstctrl 19>;
> + reset-names = "uartl";
> +
> + interrupt-parent = <&intc>;
> + interrupts = <12>;
> +
> + reg-shift = <2>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&uartlite_pins>;
> + };
> + };
> +
> + pinctrl {
> + state_default: pinctrl0 {
> + gpio {
> + ralink,group = "i2c", "jtag" ;
> + ralink,function = "gpio";
> + };
> + };
> +
> + uartf_gpio_pins: uartf_gpio {
> + uartf_gpio {
> + ralink,group = "uartf";
> + //ralink,function = "gpio uartf";
> + ralink,function = "uartf";
> + };
> + };
> +
> + uartlite_pins: uartlite {
> + uart {
> + ralink,group = "uartlite";
> + ralink,function = "uartlite";
> + };
> + };
> + };
> +
> + ethernet at 10100000 {
> + mtd-mac-address = <&factory 0x4>;
> + };
> +
> + esw at 10110000 {
> + ralink,portmap = <0x17>;
> + };
> +
> + wmac at 10180000 {
> + ralink,mtd-eeprom = <&factory 0>;
> + };
> +
> + ehci at 101c0000 {
> + status = "okay";
> + };
> +
> + ohci at 101c1000 {
> + status = "okay";
> + };
> +
> +
> + gpio-export {
> + compatible = "gpio-export";
> + #size-cells = <0>;
> +/*
> + gpio22 {
> + // WAN
> + gpio-export,name = "gpio22";
> + gpio-export,direction_may_change = <1>;
> + gpios = <&gpio1 0 0>; // path lfd dir
> + };
> + gpio23 {
> + // LAN1
> + gpio-export,name = "gpio23";
> + gpio-export,direction_may_change = <1>;
> + gpios = <&gpio1 1 0>;
> + };
> + gpio24 {
> + // LAN2
> + gpio-export,name = "gpio24";
> + gpio-export,direction_may_change = <1>;
> + gpios = <&gpio1 2 0>;
> + };
> +
> + // UARTF - UART1
> + gpio7 {
> + // UARTF_RTS_N - HW Pin 6
> + gpio-export,name = "gpio7";
> + gpio-export,direction_may_change = <1>;
> + gpios = <&gpio0 7 0>;
> + };
> + gpio8 {
> + // UARTF_TXD - HW Pin 10
> + gpio-export,name = "gpio8";
> + gpio-export,direction_may_change = <1>;
> + gpios = <&gpio0 8 0>;
> + };
> + gpio9 {
> + // UARTF_CTS_N - HW Pin 5
> + gpio-export,name = "gpio9";
> + gpio-export,direction_may_change = <1>;
> + gpios = <&gpio0 9 0>;
> + };
> + gpio10 {
> + // UARTF_RXD - HW Pin 9
> + gpio-export,name = "gpio10";
> + gpio-export,direction_may_change = <1>;
> + gpios = <&gpio0 10 0>;
> + };
> + gpio11 {
> + // UARTF_DTR_N - HW Pin 8
> + gpio-export,name = "gpio11";
> + gpio-export,direction_may_change = <1>;
> + gpios = <&gpio0 11 0>;
> + };
> + gpio12 {
> + // UARTF_DCD_N - HW Pin 12
> + gpio-export,name = "gpio12";
> + gpio-export,direction_may_change = <1>;
> + gpios = <&gpio0 12 0>;
> + };
> + gpio13 {
> + // UARTF_DSR_N - HW Pin 11
> + gpio-export,name = "gpio13";
> + gpio-export,direction_may_change = <1>;
> + gpios = <&gpio0 13 0>;
> + };
> + gpio14 {
> + // UARTF_RIN - HW Pin 7
> + gpio-export,name = "gpio14";
> + gpio-export,direction_may_change = <1>;
> + gpios = <&gpio0 14 0>;
> + };
> +
> + // UARTLITE - UART2
> + gpio15 {
> + // UART2_TXD - HW Pin 20
> + gpio-export,name = "gpio15";
> + gpio-export,direction_may_change = <1>;
> + gpios = <&gpio0 15 0>;
> + };
> + gpio16 {
> + // UART2_RXD - HW Pin 18
> + gpio-export,name = "gpio16";
> + gpio-export,direction_may_change = <1>;
> + gpios = <&gpio0 16 0>;
> + };
> +
> +*/
> +/*
> + // If you want to use this comment out the corrosponding
> gpio-keys-polled
> + gpio0 {
> + // wps btn
> + gpio-export,name = "gpio0";
> + gpio-export,direction_may_change = <1>;
> + gpios = <&gpio0 0 1>;
> + };
> +*/
> +
> + gpio19 {
> + // SCM1
> + gpio-export,name = "gpio19";
> + gpio-export,direction_may_change = <1>;
> + gpios = <&gpio0 19 1>;
> + };
> + gpio2 {
> + // SCM2
> + gpio-export,name = "gpio2";
> + gpio-export,direction_may_change = <1>;
> + gpios = <&gpio0 2 1>;
> + };
> +
> + };
> +
> +
> +
> +
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> + run {
> + label = "wizfi630a::run";
> + gpios = <&gpio0 1 1>;
> + };
> + uart1 {
> + label = "wizfi630a::uart1";
> + gpios = <&gpio0 18 1>;
> + };
> + uart2 {
> + label = "wizfi630a::uart2";
> + gpios = <&gpio0 21 1>;
> + };
> + wps {
> + label = "wizfi630a::wps";
> + gpios = <&gpio0 20 1>;
> + };
> + };
> +
> +
> + gpio-keys-polled {
> + compatible = "gpio-keys-polled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + poll-interval = <20>;
> + reset {
> + label = "reset";
> + gpios = <&gpio0 17 1>;
> + linux,code = <0x198>;
> + };
> +
> + wps {
> + label = "wps";
> + gpios = <&gpio0 0 1>;
> + linux,code = <0x211>;
> + };
> +/*
> + // If you want to use this comment out the corrosponding export
> + scm1 {
> + label = "SCM1";
> + gpios = <&gpio0 19 1>;
> + linux,code = <0x100>;
> + };
> +
> + scm2 {
> + label = "SCM2";
> + gpios = <&gpio0 2 1>;
> + linux,code = <0x101>;
> + };
> +*/
> +
> + };
> +
> +
> +};
> diff --git a/target/linux/ramips/image/Makefile
> b/target/linux/ramips/image/Makefile
> index 409ff26..fbc6775 100644
> --- a/target/linux/ramips/image/Makefile
> +++ b/target/linux/ramips/image/Makefile
> @@ -673,6 +673,8 @@ Image/Build/Profile/WNCE2001=$(call
> BuildFirmware/WNCE2001/$(1),$(1),wnce2001,WN
>
> Image/Build/Profile/WR512-3GN=$(call
> BuildFirmware/DefaultDualSize/$(1),$(1),wr512-3ng,WR512-3GN)
>
> +Image/Build/Profile/WIZFI630A=$(call
> BuildFirmware/Default16M/$(1),$(1),wizfi630a,WIZFI630A)
> +
> Image/Build/Profile/WT1520=$(call
> BuildFirmware/PorayDualSize/$(1),$(1),wt1520,WT1520)
>
> Image/Build/Profile/UR-326N4G=$(call
> BuildFirmware/Default4M/$(1),$(1),ur-326n4g,UR-326N4G)
> @@ -761,6 +763,7 @@ define Image/Build/Profile/Default
> $(call Image/Build/Profile/W306R_V20,$(1))
> $(call Image/Build/Profile/W502U,$(1))
> $(call Image/Build/Profile/WCR150GN,$(1))
> + $(call Image/Build/Profile/WIZFI630A,$(1))
> $(call Image/Build/Profile/WHRG300N,$(1))
> $(call Image/Build/Profile/WIZARD8800,$(1))
> $(call Image/Build/Profile/WL_330N,$(1))
> diff --git a/target/linux/ramips/rt305x/profiles/wizfi630a.mk
> b/target/linux/ramips/rt305x/profiles/wizfi630a.mk
> new file mode 100644
> index 0000000..22136b9
> --- /dev/null
> +++ b/target/linux/ramips/rt305x/profiles/wizfi630a.mk
> @@ -0,0 +1,18 @@
> +#
> +# Copyright (C) 2014 OpenWrt.org
> +#
> +# This is free software, licensed under the GNU General Public License v2.
> +# See /LICENSE for more information.
> +#
> +
> +define Profile/WIZFI630A
> + NAME:=WIZnet WizFi630A
> + PACKAGES:=\
> + kmod-usb-core kmod-usb-ohci kmod-usb2
> +endef
> +
> +define Profile/WIZFI630A/Description
> + Package set for WIZnet WizFi630A board
> +endef
> +
> +$(eval $(call Profile,WIZFI630A))
> --
> 1.7.10.4
>
>
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list