[OpenWrt-Devel] Change OpenWrt Wifi default settings

[David Lang]

to make the config be there after a factory reset, you need to put the changes 
into the image that you build.

you already did this for /etc/config/network, do the same thing for 
/etc/config/wireless

David Lang

On Sun, 2 Aug 2015, John kerry wrote:

> Hi Leiten,
>
> I have one issue, after upgrading this firmware it will load wireless
> configuration with this changes, actually it should load when i do factory
> reset.
>
> Thanks,
>
> On Sun, Aug 2, 2015 at 3:45 PM, John kerry <kerry9842 at gmail.com> wrote:
>
>> Hi Leiten,
>>
>> Thank you so much, Its working :)
>>
>> On Sun, Aug 2, 2015 at 3:12 PM, N.Leiten <nickleiten at gmail.com> wrote:
>>
>>> Hi,
>>>
>>> Don't answer to my e-mail only, you need to add openwrt-devel maillist to
>>> CC or just answer to CC, in each case I'll receive message but also
>>> everyone could see all discussion.
>>>
>>> In email dated Воскресенье - 02 августа 2015 12:54:32 user John kerry
>>> wrote:
>>>> Hi Leiten,
>>>>
>>>> I have added new files under and written below :
>>>> vi target/linux/ar71xx/base-files/etc/uci-defaults/wireless
>>>
>>> Use index in prefix of filename to set order of execution, so it'll be
>>> like '99-wireless'.
>>>
>>>>
>>>> #!/bin/sh
>>>> #
>>>> # Copyright (c) 2013 The Linux Foundation. All rights reserved.
>>>> # Copyright (C) 2011 OpenWrt.org
>>>> #
>>>>
>>>> [ -e /etc/config/wireless ] && exit 0
>>>
>>> Here is the problem. When uci-defaults invoke scripts there's already
>>> preconfiguration done and /etc/config/wireless already exists, so your
>>> script just exit at this point. Remove this line.
>>>
>>>>
>>>> touch /etc/config/wireless
>>>>
>>>> uci set wireless. at wifi-device[0].disabled=0;
>>>> uci set system. at system[0].hostname=test_ap
>>>> uci set wireless. at wifi-iface[0].mode=ap
>>>> uci set wireless. at wifi-iface[0].ssid=CD-2.4D
>>>> uci set wireless. at wifi-iface[0].encryption=none
>>>> uci set wireless. at wifi-iface[0].wds=1
>>>> uci set wireless.radio0.disabled=0
>>>>
>>>> uci commit wireless
>>>>
>>>> exit 0
>>>>
>>>> and compile the source code using make V=s but still not changed default
>>>> settings.
>>>>
>>>> Please help me to make it works.
>>>>
>>>> Thanks,
>>>>
>>>>
>>>> On Sat, Aug 1, 2015 at 4:38 PM, N.Leiten <nickleiten at gmail.com> wrote:
>>>>
>>>>> You can also use uci-defaults mechanism for your purpose. Just put
>>>>> script in base-files/etc/uci-defaults and set your preferrable
>>>>> parameters with uci and don't forget to 'exit 0' at the end of script,
>>>>> in elsecase it'll be run every time at boot ruining changes.
>>>>>
>>>>> 2015-07-31 12:08 GMT+03:00 John kerry <kerry9842 at gmail.com>:
>>>>>> Hi,
>>>>>>
>>>>>> I am working on Ar71xx openWRT Luci project. By default the Wi-Fi is
>>>>>> disabled and SSID is OpenWrt. I need to change the default settings.
>>>>>> Could anyone help me to change the default settings.
>>>>>>
>>>>>>
>>>>>> Best Regards,
>>>>>> John
>>>>>>
>>>>>> _______________________________________________
>>>>>> openwrt-devel mailing list
>>>>>> openwrt-devel at lists.openwrt.org
>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>>>
>>>>> _______________________________________________
>>>>> openwrt-devel mailing list
>>>>> openwrt-devel at lists.openwrt.org
>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>>>
>>> _______________________________________________
>>> openwrt-devel mailing list
>>> openwrt-devel at lists.openwrt.org
>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>>>
>>
>>
>
-------------- next part --------------
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel