[OpenWrt-Devel] [PATCH 1/3] uboot-oxnas: re-add IC+ phy driver
Daniel Golle
daniel at makrotopia.org
Wed Dec 3 10:03:40 EST 2014
KD20 got an IC+ phy, without the driver the phy is not properly
initialized resulting in ethernet not working unless being already
initialized by the vendor loader.
upstream commit 368b4d2b49bbbf379d9334747fbbd2aaaafe4356
drivers: net: remove dead drivers
removed icplus.c due to the lack of in-tree users.
Partially revert that commit adding back the IC+ driver.
Signed-off-by: Daniel Golle <daniel at makrotopia.org>
---
.../boot/uboot-oxnas/files/include/configs/ox820.h | 1 +
.../boot/uboot-oxnas/patches/200-icplus-phy.patch | 129 +++++++++++++++++++++
2 files changed, 130 insertions(+)
create mode 100644 package/boot/uboot-oxnas/patches/200-icplus-phy.patch
diff --git a/package/boot/uboot-oxnas/files/include/configs/ox820.h b/package/boot/uboot-oxnas/files/include/configs/ox820.h
index e3c71e6..85ee3b4 100644
--- a/package/boot/uboot-oxnas/files/include/configs/ox820.h
+++ b/package/boot/uboot-oxnas/files/include/configs/ox820.h
@@ -76,6 +76,7 @@
#define CONFIG_CMD_MII
#define CONFIG_PHYLIB
#define CONFIG_PHY_REALTEK
+#define CONFIG_PHY_ICPLUS
/* spl */
#ifdef CONFIG_SPL_BUILD
diff --git a/package/boot/uboot-oxnas/patches/200-icplus-phy.patch b/package/boot/uboot-oxnas/patches/200-icplus-phy.patch
new file mode 100644
index 0000000..3db7816
--- /dev/null
+++ b/package/boot/uboot-oxnas/patches/200-icplus-phy.patch
@@ -0,0 +1,129 @@
+From e719404ee1241af679a51879eaad291bc27e4817 Mon Sep 17 00:00:00 2001
+From: Daniel Golle <daniel at makrotopia.org>
+Date: Tue, 2 Dec 2014 14:46:05 +0100
+Subject: [PATCH] net/phy: add back icplus driver
+
+IC+ phy driver was removed due to the lack of users some time ago.
+Add it back, so we can use it.
+---
+ drivers/net/phy/Makefile | 1 +
+ drivers/net/phy/icplus.c | 80 ++++++++++++++++++++++++++++++++++++++++++++++++
+ drivers/net/phy/phy.c | 3 ++
+ 3 files changed, 84 insertions(+)
+ create mode 100644 drivers/net/phy/icplus.c
+
+--- a/drivers/net/phy/Makefile
++++ b/drivers/net/phy/Makefile
+@@ -15,6 +15,7 @@ obj-$(CONFIG_PHY_ATHEROS) += atheros.o
+ obj-$(CONFIG_PHY_BROADCOM) += broadcom.o
+ obj-$(CONFIG_PHY_DAVICOM) += davicom.o
+ obj-$(CONFIG_PHY_ET1011C) += et1011c.o
++obj-$(CONFIG_PHY_ICPLUS) += icplus.o
+ obj-$(CONFIG_PHY_LXT) += lxt.o
+ obj-$(CONFIG_PHY_MARVELL) += marvell.o
+ obj-$(CONFIG_PHY_MICREL) += micrel.o
+--- /dev/null
++++ b/drivers/net/phy/icplus.c
+@@ -0,0 +1,80 @@
++/*
++ * ICPlus PHY drivers
++ *
++ * SPDX-License-Identifier: GPL-2.0+
++ *
++ * Copyright (c) 2007 Freescale Semiconductor, Inc.
++ */
++#include <phy.h>
++
++/* IP101A/G - IP1001 */
++#define IP10XX_SPEC_CTRL_STATUS 16 /* Spec. Control Register */
++#define IP1001_SPEC_CTRL_STATUS_2 20 /* IP1001 Spec. Control Reg 2 */
++#define IP1001_PHASE_SEL_MASK 3 /* IP1001 RX/TXPHASE_SEL */
++#define IP1001_APS_ON 11 /* IP1001 APS Mode bit */
++#define IP101A_G_APS_ON 2 /* IP101A/G APS Mode bit */
++#define IP101A_G_IRQ_CONF_STATUS 0x11 /* Conf Info IRQ & Status Reg */
++#define IP101A_G_IRQ_PIN_USED (1<<15) /* INTR pin used */
++#define IP101A_G_IRQ_DEFAULT IP101A_G_IRQ_PIN_USED
++
++static int ip1001_config(struct phy_device *phydev)
++{
++ int c;
++
++ /* Enable Auto Power Saving mode */
++ c = phy_read(phydev, MDIO_DEVAD_NONE, IP1001_SPEC_CTRL_STATUS_2);
++ if (c < 0)
++ return c;
++ c |= IP1001_APS_ON;
++ c = phy_write(phydev, MDIO_DEVAD_NONE, IP1001_SPEC_CTRL_STATUS_2, c);
++ if (c < 0)
++ return c;
++
++ /* INTR pin used: speed/link/duplex will cause an interrupt */
++ c = phy_write(phydev, MDIO_DEVAD_NONE, IP101A_G_IRQ_CONF_STATUS,
++ IP101A_G_IRQ_DEFAULT);
++ if (c < 0)
++ return c;
++
++ if (phydev->interface == PHY_INTERFACE_MODE_RGMII) {
++ /*
++ * Additional delay (2ns) used to adjust RX clock phase
++ * at RGMII interface
++ */
++ c = phy_read(phydev, MDIO_DEVAD_NONE, IP10XX_SPEC_CTRL_STATUS);
++ if (c < 0)
++ return c;
++
++ c |= IP1001_PHASE_SEL_MASK;
++ c = phy_write(phydev, MDIO_DEVAD_NONE, IP10XX_SPEC_CTRL_STATUS,
++ c);
++ if (c < 0)
++ return c;
++ }
++
++ return 0;
++}
++
++static int ip1001_startup(struct phy_device *phydev)
++{
++ genphy_update_link(phydev);
++ genphy_parse_link(phydev);
++
++ return 0;
++}
++static struct phy_driver IP1001_driver = {
++ .name = "ICPlus IP1001",
++ .uid = 0x02430d90,
++ .mask = 0x0ffffff0,
++ .features = PHY_GBIT_FEATURES,
++ .config = &ip1001_config,
++ .startup = &ip1001_startup,
++ .shutdown = &genphy_shutdown,
++};
++
++int phy_icplus_init(void)
++{
++ phy_register(&IP1001_driver);
++
++ return 0;
++}
+--- a/drivers/net/phy/phy.c
++++ b/drivers/net/phy/phy.c
+@@ -454,6 +454,9 @@ int phy_init(void)
+ #ifdef CONFIG_PHY_ET1011C
+ phy_et1011c_init();
+ #endif
++#ifdef CONFIG_PHY_ICPLUS
++ phy_icplus_init();
++#endif
+ #ifdef CONFIG_PHY_LXT
+ phy_lxt_init();
+ #endif
+--- a/include/phy.h
++++ b/include/phy.h
+@@ -225,6 +225,7 @@ int phy_atheros_init(void);
+ int phy_broadcom_init(void);
+ int phy_davicom_init(void);
+ int phy_et1011c_init(void);
++int phy_icplus_init(void);
+ int phy_lxt_init(void);
+ int phy_marvell_init(void);
+ int phy_micrel_init(void);
--
2.1.3
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list