[FS#4254] ath10k firmware load error for qca9888

OpenWrt Bugs openwrt-bugs at lists.openwrt.org
Thu Feb 3 23:24:23 PST 2022


THIS IS AN AUTOMATED MESSAGE, DO NOT REPLY.

A new Flyspray task has been opened.  Details are below. 

User who did this - janpieter sollie (jpsollie1) 

Attached to Project - OpenWrt/LEDE Project
Summary - ath10k firmware load error for qca9888
Task Type - Bug Report
Category - Base system
Status - Unconfirmed
Assigned To - 
Operating System - All
Severity - Medium
Priority - Very Low
Reported Version - Trunk
Due in Version - Undecided
Due Date - Undecided
Details - Device problem occurs on:
BananaPI R64 (MT7622) with QCA9888 pcie card

Software versions of OpenWrt/LEDE release, packages, etc.
Master branch, kmod-ath10k + vanilla firmware / kmod-ath10k-ct + ct firmware

Steps to reproduce:
install kmod-ath10k
install board / chip firmware
reboot

error reported by dmesg:

[   13.090191] ath10k_pci 0000:01:00.0: assign IRQ: got 147
[   13.095519] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x56.
[   13.104003] pci 0000:00:00.0: enabling bus mastering
[   13.108989] ath10k_pci 0000:01:00.0: enabling device (0000 -> 0002)
[   13.115357] ath10k_pci 0000:01:00.0: enabling bus mastering
[   13.121569] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   19.195765] ath10k_pci 0000:01:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
[   19.205105] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   19.213696] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9888-fH-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,htt-mgt-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 9a038867
[   21.260278] ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=30 from ath10k/QCA9888/hw2.0/board-2.bin
[   21.281106] ath10k_pci 0000:01:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0
[   21.290557] ath10k_pci 0000:01:00.0: failed to fetch board file: -12
[   21.297037] ath10k_pci 0000:01:00.0: could not probe fw (-12)


More information can be found at the following URL:
https://bugs.openwrt.org/index.php?do=details&task_id=4254

You are receiving this message because you have requested it from the Flyspray bugtracking system.  If you did not expect this message or don't want to receive mails in future, you can change your notification settings at the URL shown above.



More information about the openwrt-bugs mailing list