[FS#3824] Sitecom WLR-8100v1 USB3 broken (Attachment added)

[OpenWrt Bugs]

THIS IS AN AUTOMATED MESSAGE, DO NOT REPLY.

A new Flyspray task has been opened.  Details are below. 

User who did this - plntyk (plntyk) 

Attached to Project - OpenWrt/LEDE Project
Summary - Sitecom WLR-8100v1 USB3 broken
Task Type - Bug Report
Category - Kernel
Status - Unconfirmed
Assigned To - 
Operating System - All
Severity - High
Priority - Very Low
Reported Version - Trunk
Due in Version - Undecided
Due Date - Undecided
Details - Sitecom WLR-8100v1 (Sitecom WLR-8100v1 001 X8 AC1750) with integrated Etron EJ168A USB3 Controller [1b6f:7023]

USB3 port does not work
USB3 port with usb2 mode does not work
USB2 port works

serial console bootlog attached with lsusb -v output

error when plugging in:

- MT76x2u USB3 WLAN Stick (AVM AC860)
- similar error with USB2 Sandisk Cruzer in USB3 port
- USB2 works fine

 [  242.139499] usb 2-1: new high-speed USB device number 2 using xhci_hcd
[  242.296773] usb-storage 2-1:1.0: USB Mass Storage device detected
[  242.315697] scsi host0: usb-storage 2-1:1.0
[  242.732028] usb 2-1: USB disconnect, device number 2
[  243.572844] usb 2-1: new high-speed USB device number 3 using xhci_hcd
[  243.863787] usb 2-1: reset high-speed USB device number 3 using xhci_hcd
[  249.227352] usb 2-1: device descriptor read/64, error -145
[  264.842949] usb 2-1: device descriptor read/64, error -145
[  265.082936] usb 2-1: reset high-speed USB device number 3 using xhci_hcd
[  270.218798] usb 2-1: device descriptor read/64, error -145
[  285.832404] usb 2-1: device descriptor read/64, error -145
[  286.072347] usb 2-1: reset high-speed USB device number 3 using xhci_hcd
[  286.099195] mt76x2u 2-1:1.0: ASIC revision: 76120044
[  286.201135] mt76x2u 2-1:1.0: ROM patch build: 20141115060606a
[  286.319536] xhci_hcd 0000:00:00.0: ERROR unknown event type 37
[  286.419382] xhci_hcd 0000:00:00.0: ERROR unknown event type 37
... (multiple entries)
[  292.359183] xhci_hcd 0000:00:00.0: xHCI host not responding to stop endpoint command.
[  292.383111] xhci_hcd 0000:00:00.0: xHCI host controller not responding, assume dead
[  292.391018] xhci_hcd 0000:00:00.0: HC died; cleaning up
[  292.396412] mt76x2u 2-1:1.0: firmware upload failed: -145
[  304.743396] mt76x2u 2-1:1.0: MAC RX failed to stop
[  304.962109] mt76x2u: probe of 2-1:1.0 failed with error -5
[  304.971982] usb 2-1: USB disconnect, device number 3


lspci -v -nnn

lspci -v -nnnn
00:00.0 USB controller [0c03]: Etron Technology, Inc. EJ168 USB 3.0 Host Controller [1b6f:7023] (rev 01) (prog-if 30 [XHCI])
        Subsystem: Etron Technology, Inc. EJ168 USB 3.0 Host Controller [1b6f:7023]
        Flags: bus master, fast devsel, latency 0, IRQ 16
        Memory at 10000000 (64-bit, non-prefetchable) [size=32K]
        Capabilities: [50] Power Management version 3
        Capabilities: [70] MSI: Enable- Count=1/4 Maskable+ 64bit+
        Capabilities: [a0] Express Endpoint, MSI 00
        Capabilities: [100] Advanced Error Reporting
        Capabilities: [190] Device Serial Number 01-01-01-01-01-01-01-01
        Kernel driver in use: xhci_hcd
lspci: Unable to load libkmod resources: error -12

01:00.0 Network controller [0280]: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network Adapter [168c:003c]
        Device tree node: /sys/firmware/devicetree/base/ahb/pcie-controller at 18250000/wifi at 0,0
        Flags: bus master, fast devsel, latency 0, IRQ 17
        Memory at 12000000 (64-bit, non-prefetchable) [size=2M]
        Expansion ROM at 12200000 [virtual] [disabled] [size=64K]
        Capabilities: [40] Power Management version 3
        Capabilities: [50] MSI: Enable- Count=1/8 Maskable+ 64bit-
        Capabilities: [70] Express Endpoint, MSI 00
        Capabilities: [100] Advanced Error Reporting
        Capabilities: [140] Virtual Channel
        Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00
        Kernel driver in use: ath10k_pci



One or more files have been attached.

More information can be found at the following URL:
https://bugs.openwrt.org/index.php?do=details&task_id=3824

You are receiving this message because you have requested it from the Flyspray bugtracking system.  If you did not expect this message or don't want to receive mails in future, you can change your notification settings at the URL shown above.