[FS#3948] ath10k not working on clearfog pro with openwrt-21.02

[OpenWrt Bugs]

THIS IS AN AUTOMATED MESSAGE, DO NOT REPLY.

A new Flyspray task has been opened.  Details are below. 

User who did this - damnms (damnms) 

Attached to Project - OpenWrt/LEDE Project
Summary - ath10k not working on clearfog pro with openwrt-21.02
Task Type - Bug Report
Category - Kernel
Status - Unconfirmed
Assigned To - 
Operating System - All
Severity - Critical
Priority - Very Low
Reported Version - openwrt-21.02
Due in Version - Undecided
Due Date - Undecided
Details - Supply the following if possible:
 - Device problem occurs on
SolidRun Clearfog Pro A1

 - Software versions of OpenWrt/LEDE release, packages, etc.
openwrt branch 21.02

 - Steps to reproduce
boot it with a compex wle600 or wle900 pcie wifi card and it will report something like:

[  683.019493] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[  683.265291] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[  683.274540] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[  683.284178] ath10k_pci 0000:02:00.0: firmware ver 10.2.4-1.0-00047 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 35bd9258
[  683.342118] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[  685.564553] ath10k_pci 0000:02:00.0: failed to receive control response completion, polling..
[  686.604459] ath10k_pci 0000:02:00.0: Service connect timeout
[  686.610136] ath10k_pci 0000:02:00.0: failed to connect htt (-110)
[  686.725295] ath10k_pci 0000:02:00.0: could not init core (-110)
[  686.731257] ath10k_pci 0000:02:00.0: could not probe fw (-110)

I configured the kernel with CONFIG_PACKAGE_ath10k-board-qca988x=y and CONFIG_PACKAGE_ath10k-firmware-qca988x=y

In openwrt 19.x i get:
 OpenWrt 19.07.7, r11306-c4a6851c72
 -----------------------------------------------------
root at OpenWrt:~# dmesg | grep ath
[   11.207948] ath10k_pci 0000:02:00.0: enabling device (0140 -> 0142)
[   11.214444] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   11.454635] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[   11.465380] ath10k_pci 0000:02:00.0: Falling back to user helper
[   11.507440] firmware ath10k!pre-cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[   11.516611] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[   11.527009] ath10k_pci 0000:02:00.0: Falling back to user helper
[   11.537130] firmware ath10k!cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[   11.545913] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
[   11.556650] ath10k_pci 0000:02:00.0: Falling back to user helper
[   11.566721] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[   11.623287] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043222ff sub 0000:0000
[   11.632549] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   11.642078] ath10k_pci 0000:02:00.0: firmware ver 10.2.4-1.0-00047 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 35bd9258
[   11.686880] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[   11.697349] ath10k_pci 0000:02:00.0: Falling back to user helper
[   11.707724] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[   11.720044] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   12.859296] ath10k_pci 0000:02:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
[   12.992322] ath: EEPROM regdomain: 0x0
[   12.992325] ath: EEPROM indicates default country code should be used
[   12.992327] ath: doing EEPROM country->regdmn map search
[   12.992330] ath: country maps to regdmn code: 0x3a
[   12.992333] ath: Country alpha2 being used: US
[   12.992334] ath: Regpair used: 0x3a
[   14.794232] ath: EEPROM regdomain: 0x82f4
[   14.804051] ath: EEPROM indicates we should expect a country code
[   14.810159] ath: doing EEPROM country->regdmn map search
[   14.815521] ath: country maps to regdmn code: 0x37
[   14.820326] ath: Country alpha2 being used: CH
[   14.824790] ath: Regpair used: 0x37
[   14.828285] ath: regdomain 0x82f4 dynamically updated by user
[   17.571688] ath10k_pci 0000:02:00.0: pdev param 0 not supported by firmware


I tried it also with the -ht firmware in v21_02 but still no luck.
Here https://githubmemory.com/repo/greearb/ath10k-ct/issues/148 someone mentioned that this might be a problem with SolidRun's PCIe implementation (if i understood that correctly).


More information can be found at the following URL:
https://bugs.openwrt.org/index.php?do=details&task_id=3948

You are receiving this message because you have requested it from the Flyspray bugtracking system.  If you did not expect this message or don't want to receive mails in future, you can change your notification settings at the URL shown above.