[FS#2431] ar71xx, Archer C7 V2 5GHz, wmi command timeout, ath10k_pci, 19.07 snapshot

OpenWrt Bugs openwrt-bugs at lists.openwrt.org
Fri Nov 27 12:13:29 EST 2020


THIS IS AN AUTOMATED MESSAGE, DO NOT REPLY.

The following task has a new comment added:

FS#2431 - ar71xx, Archer C7 V2 5GHz, wmi command timeout, ath10k_pci, 19.07 snapshot
User who did this - gamma-577 (gamma-577)

----------
Hello there!

I am a newbie to openwrt. I too have similar problem, if I may call it so. The ath10k_pci says :

wmi command 36954 timeout, restarting hardware

Then there are a handful of repeated SWBA overruns :

SWBA overrun on vdev 0, skipped old beacon

Finally leading to :

firmware crashed! (guid c5b17323-3c82-42cd-87fe-8d893dce43b4)

Then there is some relevent dump info.

After that thre are some wmi commands which keep failing, and subsequent cleanup.

After that the device is successfully recovered.

Anyway, here is a seemingly complete event log :


[480451.284333] ath10k_pci 0000:02:00.0: wmi command 36954 timeout, restarting hardware
[480451.377328] ath10k_pci 0000:02:00.0: SWBA overrun on vdev 0, skipped old beacon
[480451.479728] ath10k_pci 0000:02:00.0: SWBA overrun on vdev 0, skipped old beacon
[480451.582123] ath10k_pci 0000:02:00.0: SWBA overrun on vdev 0, skipped old beacon
[480451.684536] ath10k_pci 0000:02:00.0: SWBA overrun on vdev 0, skipped old beacon
[480451.786982] ath10k_pci 0000:02:00.0: SWBA overrun on vdev 0, skipped old beacon
[480451.889346] ath10k_pci 0000:02:00.0: SWBA overrun on vdev 0, skipped old beacon
[480451.991753] ath10k_pci 0000:02:00.0: SWBA overrun on vdev 0, skipped old beacon
[480452.094169] ath10k_pci 0000:02:00.0: SWBA overrun on vdev 0, skipped old beacon
[480452.196581] ath10k_pci 0000:02:00.0: SWBA overrun on vdev 0, skipped old beacon
[480452.207091] ath10k_pci 0000:02:00.0: firmware crashed! (guid 725b129d-f1ca-4619-ad74-04a35bc483b9)
[480452.214822] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[480452.224106] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[480452.238658] ath10k_pci 0000:02:00.0: firmware ver 10.1-ct-8x-__fW-022-538f0906 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 e1c91a74
[480452.267795] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[480452.275142] ath10k_pci 0000:02:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[480452.286757] ath10k_pci 0000:02:00.0: firmware register dump:
[480452.291144] ath10k_pci 0000:02:00.0: [00]: 0x4100016C 0x000015B3 0x009AAE19 0x00955B31
[480452.299118] ath10k_pci 0000:02:00.0: [04]: 0x009AAE19 0x00060730 0x00000005 0x00000032
[480452.307124] ath10k_pci 0000:02:00.0: [08]: 0x0040ED60 0x004111F0 0x055299A8 0x00400000
[480452.315131] ath10k_pci 0000:02:00.0: [12]: 0x00000009 0x00000000 0x0095808C 0x009580A2
[480452.323139] ath10k_pci 0000:02:00.0: [16]: 0x00958080 0x0094078E 0x00000000 0x00000000
[480452.331147] ath10k_pci 0000:02:00.0: [20]: 0x409AAE19 0x0040AE44 0x00000005 0x0040D060
[480452.339167] ath10k_pci 0000:02:00.0: [24]: 0x80944C31 0x0040AEA4 0xF573FFFF 0xC09AAE19
[480452.347163] ath10k_pci 0000:02:00.0: [28]: 0x80942BE7 0x0040AED4 0x00411454 0x00000000
[480452.355170] ath10k_pci 0000:02:00.0: [32]: 0x809B74DD 0x0040AEF4 0x004090A0 0x00409110
[480452.363183] ath10k_pci 0000:02:00.0: [36]: 0x80940F18 0x0040AF14 0x00000008 0x00403A20
[480452.371187] ath10k_pci 0000:02:00.0: [40]: 0x80940EEA 0x0040AF44 0x00400000 0x00000000
[480452.379193] ath10k_pci 0000:02:00.0: [44]: 0x80940F31 0x0040AF64 0x00401C10 0x00400600
[480452.387202] ath10k_pci 0000:02:00.0: [48]: 0x40940024 0x0040AF84 0x004068E8 0x004068E8
[480452.395208] ath10k_pci 0000:02:00.0: [52]: 0x00000000 0x0040AFA4 0x009BB001 0x00040020
[480452.403227] ath10k_pci 0000:02:00.0: [56]: 0x00403994 0x00000000 0x00000001 0x00400600
[480452.411215] ath10k_pci 0000:02:00.0: Copy Engine register dump:
[480452.417237] ath10k_pci 0000:02:00.0: [00]: 0x00057400   2   2   3   3
[480452.423763] ath10k_pci 0000:02:00.0: [01]: 0x00057800  22  22  56  57
[480452.430293] ath10k_pci 0000:02:00.0: [02]: 0x00057c00  30  30  29  30
[480452.436818] ath10k_pci 0000:02:00.0: [03]: 0x00058000   7   7   7   7
[480452.443359] ath10k_pci 0000:02:00.0: [04]: 0x00058400   3   3  43   3
[480452.449877] ath10k_pci 0000:02:00.0: [05]: 0x00058800  18  18 177 178
[480452.456403] ath10k_pci 0000:02:00.0: [06]: 0x00058c00  27  27  27  27
[480452.462931] ath10k_pci 0000:02:00.0: [07]: 0x00059000   0   0   0   0
[480452.471587] ath10k_pci 0000:02:00.0: debug log header, dbuf: 0x412708  dropped: 0
[480452.478794] ath10k_pci 0000:02:00.0: [0] next: 0x412720 buf: 0x41056c sz: 1500 len: 448 count: 17 free: 0
[480452.488508] ath10k_pci 0000:02:00.0: ath10k_pci ATH10K_DBG_BUFFER:
[480452.493702] ath10k: [0000]: A9995205 3204FC17 00000000 06300000 05000000 07000000 00000000 A9995205
[480452.502830] ath10k: [0008]: 3204FC17 03771071 00000000 00000000 FFFFFFFF FFFFFFFF A9995205 3204FC0F
[480452.511984] ath10k: [0016]: 13771071 03000000 03000000 A9995205 3204FC17 03771071 360A0100 350A0000
[480452.521108] ath10k: [0024]: 16000000 16000000 A9995205 3204FC17 03771071 1E1B0200 1D1B0000 1E000000
[480452.530247] ath10k: [0032]: 1E000000 A9995205 3204FC17 03771071 00000300 00000200 FFFFFFFF FFFFFFFF
[480452.539400] ath10k: [0040]: A9995205 3204FC0F 13771071 07000000 07000000 A9995205 3204FC17 03771071
[480452.548539] ath10k: [0048]: 00000400 00000100 FFFFFFFF FFFFFFFF A9995205 3204FC0F 13771071 03000000
[480452.557665] ath10k: [0056]: 03000000 A9995205 3204FC17 03771071 B20A0500 B10A0000 12000000 12000000
[480452.566803] ath10k: [0064]: A9995205 3204FC17 00000000 00000000 00000000 00000000 00000000 A9995205
[480452.575941] ath10k: [0072]: 3204FC17 01000000 00000000 00000000 00000000 00000000 A9995205 3204FC17
[480452.585082] ath10k: [0080]: 02000000 00000000 00000000 04000000 00000000 A9995205 3204FC17 03000000
[480452.594220] ath10k: [0088]: 00000000 00000000 00000000 00000000 A9995205 3204FC17 04000000 00000000
[480452.603359] ath10k: [0096]: 00000000 00000000 00000000 A9995205 3204FC13 45331091 467A5205 A8995205
[480452.612501] ath10k: [0104]: 401F0000 A9995205 0100FC17 B3150000 B3150000 34AD4000 6C010041 180F4300
[480452.621633] ath10k_pci 0000:02:00.0: ATH10K_END
[480452.627320] ath10k_pci 0000:02:00.0: [1] next: 0x412708 buf: 0x410b5c sz: 1500 len: 0 count: 0 free: 0
[480454.351076] ath10k_pci 0000:02:00.0: wmi command 36977 timeout, restarting hardware
[480454.357499] ath10k_pci 0000:02:00.0: failed to send pdev bss chan info request: -11
[480457.423220] ath10k_pci 0000:02:00.0: wmi command 40859 timeout, restarting hardware
[480457.429669] ath10k_pci 0000:02:00.0: failed to send wmi nop: -11
[480457.436380] ath10k_pci 0000:02:00.0: removing peer, cleanup-all, deleting: peer 861c6600 vdev: 0 addr: c8:91:f9:3b:1c:bf 
[480457.553604] ieee80211 phy0: Hardware restart was requested
[480457.559818] ath10k_pci 0000:02:00.0: failed to set beacon mode for vdev 0: -143
[480457.565922] ath10k_pci 0000:02:00.0: failed to set dtim period for vdev 0: -143
[480458.588660] ath10k_pci 0000:02:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
[480458.604164] ath10k_pci 0000:02:00.0: wmi print 'P 128 V 8 T 410'
[480458.609269] ath10k_pci 0000:02:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta: 0'
[480458.617086] ath10k_pci 0000:02:00.0: wmi print 'alloc rem: 20984 iram: 25656'
[480458.680939] ath10k_pci 0000:02:00.0: pdev param 0 not supported by firmware
[480458.703454] ath10k_pci 0000:02:00.0: device successfully recovered
[480696.276498] ath10k_pci 0000:02:00.0: SWBA overrun on vdev 0, skipped old beacon
[480696.378902] ath10k_pci 0000:02:00.0: SWBA overrun on vdev 0, skipped old beacon
[480696.481308] ath10k_pci 0000:02:00.0: SWBA overrun on vdev 0, skipped old beacon
[480696.583715] ath10k_pci 0000:02:00.0: SWBA overrun on vdev 0, skipped old beacon
[480696.686120] ath10k_pci 0000:02:00.0: SWBA overrun on vdev 0, skipped old beacon
[480696.788591] ath10k_pci 0000:02:00.0: SWBA overrun on vdev 0, skipped old beacon
[480696.890949] ath10k_pci 0000:02:00.0: SWBA overrun on vdev 0, skipped old beacon
[480696.993346] ath10k_pci 0000:02:00.0: SWBA overrun on vdev 0, skipped old beacon


----

Device details :

Device : BTHH5A

Architecture : xRX200 rev 1.2

Firmware version : OpenWrt 19.07.4 r11208-ce6496d796 / LuCI openwrt-19.07 branch git-20.247.75781-0d0ab01

Kernel : 4.14.195

----
Package list :


ath10k-firmware-qca988x-ct - 2020-07-02-1
base-files - 204.2-r11208-ce6496d796
bind-dig - 9.16.8-1
bind-libs - 9.16.8-1
block-mount - 2020-05-12-84269037-1
br2684ctl - 2.5.2-7
bspatch - 4.3-1
busybox - 1.30.1-6
ca-certificates - 20200601-1
cgi-io - 19
ddns-scripts - 2.7.8-13
dnsmasq - 2.80-16.1
dropbear - 2019.78-2
dsl-vrx200-firmware-xdsl-a - 05.08.01.08.01.06_05.08.00.0B.01.01_osc-1
dsl-vrx200-firmware-xdsl-b-patch - 05.08.01.08.01.06_05.08.00.0B.01.01_osc-1
firewall - 2019-11-22-8174814a-2
fstools - 2020-05-12-84269037-1
fwtool - 2
getrandom - 2019-06-16-4df34a4d-3
hostapd-common - 2019-08-08-ca8c2bd2-4
ip6tables - 1.8.3-1
iptables - 1.8.3-1
iw - 5.0.1-1
iwinfo - 2019-10-16-07315b6f-1
jshn - 2020-05-25-66195aee-1
jsonfilter - 2018-02-04-c7e938d6-1
kernel - 4.14.195-1-0f59e90218b95a909e229a713d3da157
kmod-ath - 4.14.195+4.19.137-1-2
kmod-ath10k-ct - 4.14.195+2019-09-09-5e8cd86f-1
kmod-ath9k - 4.14.195+4.19.137-1-2
kmod-ath9k-common - 4.14.195+4.19.137-1-2
kmod-atm - 4.14.195-1
kmod-cfg80211 - 4.14.195+4.19.137-1-2
kmod-crypto-aead - 4.14.195-1
kmod-crypto-hash - 4.14.195-1
kmod-crypto-manager - 4.14.195-1
kmod-crypto-null - 4.14.195-1
kmod-crypto-pcompress - 4.14.195-1
kmod-fs-exfat - 4.14.195+2018-04-17-01c30ad5-2
kmod-fs-vfat - 4.14.195-1
kmod-gpio-button-hotplug - 4.14.195-3
kmod-hwmon-core - 4.14.195-1
kmod-ip6tables - 4.14.195-1
kmod-ipt-conntrack - 4.14.195-1
kmod-ipt-core - 4.14.195-1
kmod-ipt-nat - 4.14.195-1
kmod-ipt-offload - 4.14.195-1
kmod-leds-gpio - 4.14.195-1
kmod-lib-crc-ccitt - 4.14.195-1
kmod-ltq-atm-vr9 - 4.14.195-2
kmod-ltq-deu-vr9 - 4.14.195-1
kmod-ltq-ifxos - 4.14.195+1.5.19-4
kmod-ltq-ptm-vr9 - 4.14.195-2
kmod-ltq-vdsl-vr9 - 4.14.195+4.17.18.6-3
kmod-ltq-vdsl-vr9-mei - 4.14.195+1.5.17.6-4
kmod-mac80211 - 4.14.195+4.19.137-1-2
kmod-nf-conntrack - 4.14.195-1
kmod-nf-conntrack6 - 4.14.195-1
kmod-nf-flow - 4.14.195-1
kmod-nf-ipt - 4.14.195-1
kmod-nf-ipt6 - 4.14.195-1
kmod-nf-nat - 4.14.195-1
kmod-nf-reject - 4.14.195-1
kmod-nf-reject6 - 4.14.195-1
kmod-nls-base - 4.14.195-1
kmod-nls-cp437 - 4.14.195-1
kmod-nls-iso8859-1 - 4.14.195-1
kmod-nls-utf8 - 4.14.195-1
kmod-owl-loader - 4.14.195-1
kmod-ppp - 4.14.195-1
kmod-pppoa - 4.14.195-1
kmod-pppoe - 4.14.195-1
kmod-pppox - 4.14.195-1
kmod-scsi-core - 4.14.195-1
kmod-slhc - 4.14.195-1
kmod-usb-core - 4.14.195-1
kmod-usb-dwc2 - 4.14.195-1
kmod-usb-storage - 4.14.195-1
kmod-usb-storage-uas - 4.14.195-1
libatomic1 - 7.5.0-2
libblobmsg-json - 2020-05-25-66195aee-1
libbz2-1.0 - 1.0.8-1
libc - 1.1.24-2
libgcc1 - 7.5.0-2
libip4tc2 - 1.8.3-1
libip6tc2 - 1.8.3-1
libiwinfo-lua - 2019-10-16-07315b6f-1
libiwinfo20181126 - 2019-10-16-07315b6f-1
libjson-c2 - 0.12.1-3.1
libjson-script - 2020-05-25-66195aee-1
liblua5.1.5 - 5.1.5-3
liblucihttp-lua - 2019-07-05-a34a17d5-1
liblucihttp0 - 2019-07-05-a34a17d5-1
libmbedtls12 - 2.16.8-1
libnl-tiny - 0.1-5
libopenssl-conf - 1.1.1h-1
libopenssl1.1 - 1.1.1h-1
libpcre - 8.43-1
libpthread - 1.1.24-2
librt - 1.1.24-2
libubox20191228 - 2020-05-25-66195aee-1
libubus-lua - 2019-12-27-041c9d1c-1
libubus20191227 - 2019-12-27-041c9d1c-1
libuci20130104 - 2019-09-01-415f9e48-3
libuclient20160123 - 2020-06-17-51e16ebf-1
libusb-1.0-0 - 1.0.22-2
libustream-mbedtls20150806 - 2020-03-13-40b563b1-1
libuv1 - 1.40.0-1
libxtables12 - 1.8.3-1
linux-atm - 2.5.2-7
logd - 2019-06-16-4df34a4d-3
ltq-vdsl-app - 4.17.18.6-2
ltq-vdsl-vr9-vectoring-fw-installer - 6.8.6-3
lua - 5.1.5-3
luci - git-20.247.75781-0d0ab01-1
luci-app-ddns - 2.4.9-7
luci-app-firewall - git-20.247.75781-0d0ab01-1
luci-app-opkg - git-20.247.75781-0d0ab01-1
luci-base - git-20.247.75781-0d0ab01-1
luci-compat - git-20.313.59566-7460e9d-1
luci-lib-ip - git-20.247.75781-0d0ab01-1
luci-lib-ipkg - git-20.313.59566-7460e9d-1
luci-lib-jsonc - git-20.247.75781-0d0ab01-1
luci-lib-nixio - git-20.247.75781-0d0ab01-1
luci-mod-admin-full - git-20.247.75781-0d0ab01-1
luci-mod-network - git-20.247.75781-0d0ab01-1
luci-mod-status - git-20.247.75781-0d0ab01-1
luci-mod-system - git-20.247.75781-0d0ab01-1
luci-proto-ipv6 - git-20.247.75781-0d0ab01-1
luci-proto-ppp - git-20.247.75781-0d0ab01-1
luci-ssl - git-20.313.59566-7460e9d-1
luci-theme-bootstrap - git-20.247.75781-0d0ab01-1
mtd - 24
netifd - 2019-08-05-5e02f944-1
netperf - 2.7.0-1
odhcp6c - 2019-01-11-e199804b-16
odhcpd-ipv6only - 2020-05-03-49e4949c-3
openssl-util - 1.1.1h-1
openwrt-keyring - 2019-07-25-8080ef34-1
opkg - 2020-05-07-f2166a89-1
ppp - 2.4.7.git-2019-05-25-3
ppp-mod-pppoa - 2.4.7.git-2019-05-25-3
ppp-mod-pppoe - 2.4.7.git-2019-05-25-3
procd - 2020-03-07-09b9bd82-1
px5g-mbedtls - 9
rpcd - 2020-05-26-67c8a3fd-1
rpcd-mod-file - 2020-05-26-67c8a3fd-1
rpcd-mod-iwinfo - 2020-05-26-67c8a3fd-1
rpcd-mod-luci - 20191114
rpcd-mod-rrdns - 20170710
speedtest-netperf - 1.0.0-1
swconfig - 12
ubi-utils - 2.1.1-1
ubox - 2019-06-16-4df34a4d-3
ubus - 2019-12-27-041c9d1c-1
ubusd - 2019-12-27-041c9d1c-1
uci - 2019-09-01-415f9e48-3
uclient-fetch - 2020-06-17-51e16ebf-1
uhttpd - 2020-03-13-975dce23-1
urandom-seed - 1.0-1
urngd - 2020-01-21-c7f7b6b6-1
usbutils - 007-10
usign - 2020-05-23-f1f65026-1
wget - 1.20.3-4
wireless-regdb - 2019.06.03-1
wpad-basic - 2019-08-08-ca8c2bd2-4
zlib - 1.2.11-3


Hope this helps. Thank you!

-Gamma
----------

More information can be found at the following URL:
https://bugs.openwrt.org/index.php?do=details&task_id=2431#comment9049

You are receiving this message because you have requested it from the Flyspray bugtracking system.  If you did not expect this message or don't want to receive mails in future, you can change your notification settings at the URL shown above.



More information about the openwrt-bugs mailing list