[FS#2524] ath79-tiny: TP-Link TL-WR941ND v2.4: Marvel MV88E6060 regression between kernel v4.14 and v4.19
OpenWrt Bugs
openwrt-bugs at lists.openwrt.org
Fri Jul 10 00:00:44 EDT 2020
THIS IS AN AUTOMATED MESSAGE, DO NOT REPLY.
The following task has a new comment added:
FS#2524 - ath79-tiny: TP-Link TL-WR941ND v2.4: Marvel MV88E6060 regression between kernel v4.14 and v4.19
User who did this - Stefan Lippers-Hollmann (slh)
----------
U-Boot 1.1.4 (Jun 18 2009 - 15:08:27)
AP81 (ar7100) U-boot
DRAM:
32 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7100_enet_initialize...
No valid address in Flash. Using fixed address
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Autobooting in 1 secondsar7100>
ar7100> tftp 0x80800000 tiny.bin
set link to 100M full by lqm.
dup 1 speed 100
Using eth0 device
TFTP from server 192.168.1.169; our IP address is 192.168.1.10
Filename 'tiny.bin'.
Load address: 0x80800000
Loading: *
checksum bad
checksum bad
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
################
done
Bytes transferred = 3408133 (340105 hex)
ar7100> erase.b 0xbf020000 +0x3c0000
First 0x2 last 0x3d sector size 0x10000
[...]
Erased 60 sectors
ar7100> cp.b 0x80800000 0xbf020000 0x3c0000
Copy to Flash... write addr: bf020000
done
ar7100> reset
Resetting...
U-Boot 1.1.4 (Jun 18 2009 - 15:08:27)
AP81 (ar7100) U-boot
DRAM:
32 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7100_enet_initialize...
No valid address in Flash. Using fixed address
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Autobooting in 1 seconds## Booting image at bf020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos
Looking for OpenWrt image... found at 0xbf022000
Decompressing kernel... done!
Starting kernel at 80060000...
[ 0.000000] Linux version 5.4.50 (slh at trident) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13768-f632747704)) #0 Thu Jul 9 09:11:31 2020
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] MIPS: machine is TP-Link TL-WR941N/ND v2/v3
[ 0.000000] SoC: Atheros AR9132 rev 1
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 26412K/32768K available (3856K kernel code, 141K rwdata, 580K rodata, 1240K init, 186K bss, 6356K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] random: get_random_bytes called from 0x804da9ac with crng_init=0
[ 0.000000] CPU clock: 400.000 MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000013] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.008262] Calibrating delay loop... 264.70 BogoMIPS (lpj=132352)
[ 0.024799] pid_max: default: 32768 minimum: 301
[ 0.029950] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.037668] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.051147] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.061415] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.068671] pinctrl core: initialized pinctrl subsystem
[ 0.075621] NET: Registered protocol family 16
[ 0.114157] clocksource: Switched to clocksource MIPS
[ 0.121119] NET: Registered protocol family 2
[ 0.126950] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.135759] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.143817] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.151238] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.158134] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.165049] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.172738] NET: Registered protocol family 1
[ 0.177386] PCI: CLS 0 bytes, default 32
[ 0.186848] workingset: timestamp_bits=30 max_order=13 bucket_order=0
[ 0.203402] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.209547] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.237410] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.245228] printk: console [ttyS0] disabled
[ 0.249835] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 6250000) is a 8250
[ 0.258752] printk: console [ttyS0] enabled
[ 0.258752] printk: console [ttyS0] enabled
[ 0.267335] printk: bootconsole [early0] disabled
[ 0.267335] printk: bootconsole [early0] disabled
[ 0.288109] spi-nor spi0.0: 320s33b (4096 Kbytes)
[ 0.292934] 3 fixed-partitions partitions found on MTD device spi0.0
[ 0.299287] Creating 3 MTD partitions on "spi0.0":
[ 0.304095] 0x000000000000-0x000000020000 : "u-boot"
[ 0.310549] 0x000000020000-0x0000003f0000 : "firmware"
[ 0.320726] 2 tplink-fw partitions found on MTD device firmware
[ 0.326703] Creating 2 MTD partitions on "firmware":
[ 0.331687] 0x000000000000-0x00000017970e : "kernel"
[ 0.338062] 0x000000179710-0x0000003d0000 : "rootfs"
[ 0.344449] mtd: device 3 (rootfs) set to be root filesystem
[ 0.352623] 1 squashfs-split partitions found on MTD device rootfs
[ 0.358874] 0x000000340000-0x0000003d0000 : "rootfs_data"
[ 0.365709] 0x0000003f0000-0x000000400000 : "art"
[ 0.373110] libphy: Fixed MDIO Bus: probed
[ 0.478152] random: fast init done
[ 0.699376] libphy: ag71xx_mdio: probed
[ 0.704949] ag71xx 19000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[ 0.714973] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rmii
[ 0.724759] NET: Registered protocol family 10
[ 0.735953] Segment Routing with IPv6
[ 0.739852] NET: Registered protocol family 17
[ 0.744705] 8021q: 802.1Q VLAN Support v1.8
[ 0.768482] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 0.783333] Freeing unused kernel memory: 1240K
[ 0.787881] This architecture does not have kernel memory protection.
[ 0.794311] Run /sbin/init as init process
[ 5.814655] init: Console is alive
[ 5.818490] init: - watchdog -
[ 7.464587] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 7.738899] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 7.756768] init: - preinit -
[ 11.116652] random: jshn: uninitialized urandom read (4 bytes read)
[ 11.228695] random: jshn: uninitialized urandom read (4 bytes read)
[ 11.377953] random: jshn: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 13.495238] random: crng init done
[ 13.498645] random: 3 urandom warning(s) missed due to ratelimiting
[ 22.220372] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 22.259337] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 22.302326] procd: - early -
[ 22.305415] procd: - watchdog -
[ 23.143298] procd: - watchdog -
[ 23.146918] procd: - ubus -
[ 24.311577] procd: - init -
Please press Enter to activate this console.
[ 26.094584] kmodloader: loading kernel modules from /etc/modules.d/*
[ 26.144284] Loading modules backported from Linux version v5.7-rc3-0-g6a8b55ed4056
[ 26.151878] Backport generated by backports.git v5.7-rc3-1-0-gc0c7d2bb
[ 26.230413] xt_time: kernel timezone is -0000
[ 26.630877] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a1 mem=0xb80c0000, irq=2
[ 27.165691] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 27.343970] urngd: v1.0.2 started.
[ 100.571206] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 100.592204] jffs2_build_filesystem(): unlocking the mtd device...
[ 100.592213] done.
[ 100.600331] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 105.854607] done.
[ 105.864086] jffs2: notice: (1060) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 106.381356] overlayfs: upper fs does not support tmpfile.
BusyBox v1.31.1 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r13768-f632747704
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root at OpenWrt:/# uname -a
Linux OpenWrt 5.4.50 #0 Thu Jul 9 09:11:31 2020 mips GNU/Linux
root at OpenWrt:/# ip a
1: lo: mtu 65536 qdisc noqueue state UNKNOWN qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 00:21:27:ff:51:a6 brd ff:ff:ff:ff:ff:ff
3: wlan0: mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 00:21:27:ff:51:a6 brd ff:ff:ff:ff:ff:ff
root at OpenWrt:/# zcat /proc/config.gz | grep DSA
CONFIG_HAVE_NET_DSA=y
CONFIG_NET_DSA=y
# CONFIG_NET_DSA_TAG_8021Q is not set
# CONFIG_NET_DSA_TAG_BRCM is not set
# CONFIG_NET_DSA_TAG_BRCM_PREPEND is not set
# CONFIG_NET_DSA_TAG_GSWIP is not set
# CONFIG_NET_DSA_TAG_DSA is not set
# CONFIG_NET_DSA_TAG_EDSA is not set
# CONFIG_NET_DSA_TAG_MTK is not set
# CONFIG_NET_DSA_TAG_KSZ is not set
# CONFIG_NET_DSA_TAG_QCA is not set
# CONFIG_NET_DSA_TAG_LAN9303 is not set
# CONFIG_NET_DSA_TAG_SJA1105 is not set
CONFIG_NET_DSA_TAG_TRAILER=y
# CONFIG_NET_DSA_BCM_SF2 is not set
# CONFIG_NET_DSA_LOOP is not set
# CONFIG_NET_DSA_LANTIQ_GSWIP is not set
# CONFIG_NET_DSA_MT7530 is not set
CONFIG_NET_DSA_MV88E6060=y
# CONFIG_NET_DSA_MICROCHIP_KSZ9477 is not set
# CONFIG_NET_DSA_MICROCHIP_KSZ8795 is not set
# CONFIG_NET_DSA_MV88E6XXX is not set
# CONFIG_NET_DSA_SJA1105 is not set
# CONFIG_NET_DSA_QCA8K is not set
# CONFIG_NET_DSA_REALTEK_SMI is not set
# CONFIG_NET_DSA_SMSC_LAN9303_MDIO is not set
# CONFIG_NET_DSA_VITESSE_VSC73XX_SPI is not set
# CONFIG_NET_DSA_VITESSE_VSC73XX_PLATFORM is not set
# CONFIG_CRYPTO_ECRDSA is not set
----------
More information can be found at the following URL:
https://bugs.openwrt.org/index.php?do=details&task_id=2524#comment8545
You are receiving this message because you have requested it from the Flyspray bugtracking system. If you did not expect this message or don't want to receive mails in future, you can change your notification settings at the URL shown above.
More information about the openwrt-bugs
mailing list