[PATCH] ipq40xx: add support for Wallystech DR40x9
Robert Marko
robimarko at gmail.com
Thu Mar 16 03:04:42 PDT 2023
On Wed, 15 Mar 2023 at 15:22, Koen Vandeputte
<koen.vandeputte at citymesh.com> wrote:
>
> From: Robert Marko <robert.marko at sartura.hr>
>
> Adds support for the Wallys DR40x9 series boards.
> They come in IPQ4019 and IPQ4029 versions.
> IPQ4019/4029 only differ in that that IPQ4029 is the industrial version that is rated to higher temperatures.
>
> Specifications are:
> * CPU: Qualcomm IPQ40x9 (4x ARMv7A Cortex A7) at 716 MHz
> * RAM: 512 MB
> * Storage: 2MB of SPI-NOR, 128 MB of parallel NAND
> * USB 3.0 TypeA port for users
> * MiniPCI-E with PCI-E 2.0 link
> * MiniPCI-E for LTE modems with only USB2.0 link
> * 2 SIM card slots that are selected via GPIO11
> * MicroSD card slot
> * Ethernet: 2x GBe with 24~48V passive POE
> * SFP port (Does not work, I2C and GPIO's not connected on hardware)
> * DC Jack
> * UART header
> * WLAN: In-SoC 2x2 802.11b/g/n and 2x2 802.11a/n/ac
> * 4x MMCX connectors for WLAN
> * Reset button
> * 8x LED-s
>
> Installation instructions:
> Connect to UART, pins are like this:
> -> 3.3V | TX | RX | GND
>
> Settings are 115200 8n1
>
> Boot initramfs from TFTP:
> tftpboot 0x84000000 openwrt-ipq40xx-generic-wallys_dr40x9-initramfs-fit-uImage.itb
>
> bootm
>
> Then copy the sysupgrade image to the /tmp folder and execute sysupgrade -n <image_name>
>
> Signed-off-by: Robert Marko <robert.marko at sartura.hr>
> [Fixup dts for 2 missing crypto options]
> [Remove sfp from dts]
> [Add 'config' partition]
> [Update to latest wifi board bin files - received from Wallystech R&D]
> [Extensively tested on DR4029-V04]
> Signed-off-by: Koen Vandeputte <koen.vandeputte at citymesh.com>
> ---
> package/firmware/ipq-wifi/Makefile | 2 +
> .../ipq-wifi/board-wallys_dr40x9.qca4019 | Bin 0 -> 24316 bytes
> .../ipq40xx/base-files/etc/board.d/02_network | 1 +
> .../base-files/etc/board.d/03_gpio_switches | 3 +
> .../base-files/lib/upgrade/platform.sh | 3 +-
> .../arch/arm/boot/dts/qcom-ipq40x9-dr40x9.dts | 425 ++++++++++++++++++
> target/linux/ipq40xx/image/generic.mk | 13 +
> 7 files changed, 446 insertions(+), 1 deletion(-)
> create mode 100644 package/firmware/ipq-wifi/board-wallys_dr40x9.qca4019
> create mode 100644 target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq40x9-dr40x9.dts
>
> diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
> index 8e7fc4da39..6feac277b3 100644
> --- a/package/firmware/ipq-wifi/Makefile
> +++ b/package/firmware/ipq-wifi/Makefile
> @@ -47,6 +47,7 @@ ALLWIFIBOARDS:= \
> redmi_ax6 \
> sony_ncp-hg100-cellular \
> teltonika_rutx \
> + wallys_dr40x9 \
> xiaomi_ax3600 \
> xiaomi_ax9000 \
> zte_mf18a \
> @@ -147,6 +148,7 @@ $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac-c2,Qxwlan E2600AC C2))
> $(eval $(call generate-ipq-wifi-package,redmi_ax6,Redmi AX6))
> $(eval $(call generate-ipq-wifi-package,sony_ncp-hg100-cellular,Sony NCP-HG100/Cellular))
> $(eval $(call generate-ipq-wifi-package,teltonika_rutx,Teltonika RUTX))
> +$(eval $(call generate-ipq-wifi-package,wallys_dr40x9,Wallys DR40X9))
> $(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600))
> $(eval $(call generate-ipq-wifi-package,xiaomi_ax9000,Xiaomi AX9000))
> $(eval $(call generate-ipq-wifi-package,zte_mf18a,ZTE MF18A))
> diff --git a/package/firmware/ipq-wifi/board-wallys_dr40x9.qca4019 b/package/firmware/ipq-wifi/board-wallys_dr40x9.qca4019
> new file mode 100644
> index 0000000000000000000000000000000000000000..f23ecdfabbb90dc8d293676c4449a5fa9e90e721
> GIT binary patch
> literal 24316
> zcmeHPdr(tX8b1jj%4*?;fV{kf at JeV1A*2{2@{BY<3KkU!un1I<q(pfb9)>R1 at j)RX
> z0<|DS&^joOrihHi2gGV^?Tj+*&i=8pf3%%_bZ6FG+tKc{GrNm>?hSzi5={iA0qz&h
> zIp6v2`Of*yFDJ>p_x!kTCdP-x?-Ye|QbQBc<1>UnE|&u+C1F?&Kr~E+ii)iT#f7Xw
> zxis{xVrglpbnjLUUMoCUP`($dayhKZf^uoWfkRt&7nGFLRD=pMc$};#ISKmHU|+N_
> zk%&YBc6Ah9Cf09AFU;}*aB_5k3IJ39UWvdp(;1UV$GQR_A|m3aCr?NM>KgFNUrxp9
> zlO62fCFS;9zZTs{;29KnY`Qkx>f+qi`nof�%|#kfeL*k6<zC_1QA^<s+W$1Zqxr
> z4I8(Cta}+9h7~Hs&=N~^baZrZaIiBF0LHPIS}1O?ondl^b;D#~H#5zgq0Cg4xl-CZ
> zge{wCF`mrCP*+pUzU<Uw{>0U;wi<c%&g6uNfvyvc<<d8kBPRx-Rw2zue(e`1_r72T
> zgNcv28fyx(li|VPu9g~U_V(nMiGHjZwDF-sQ)5-OI5`@3xE~w>Ca!dygd at C>95wMV
> zbdcc=eXx__>{LDjcGp@{nw`PtOgjV{$M=F-4U`u&F+NN<7~^5Owh~Y>J+tLyz1UPx
> z6}2xo(<k*#TX|iQoV~{_VSJ#hGwB4Q+#|npFsC!>1g*lgps%q&5mgwpV^i|2mIJlh
> zq^umbn9uubK1e^ouGsX}jlrtUH=07Le2PX-7FWmYV`d^zH(@)WjGf~ebE!|-A!>ZJ
> z%DedbN0mKcb-typ`O6C>B3eBH4vy=7v%wj0b=&Cay-ELtZ%|_2vCk9O4?H2lGBTM=
> z!g4!1__MrbS{yIeXK_64zq6f-1_b!Szd*X5pFiD?PS3PoJLjB49}-b6Ap%)h8EJI7
> zFC5|LpP&3NHHDo4 at tJ}CI@^DL_|x}>Hmu>M^^RnF`~Sgq&hQPJ^?&;G at grT^B at 7qu
> zx^xJhk3g-ou6YPcm at zVv$I~UKa5-#NNF-KWu*QRZaPeLiN5dyDCqqyKiAUp+a5Nk#
> zRUEE6`d)Ke$9x3{rsbAZ3I(OGDGw-!7wX0K61$)-hzFX0Ca at D8Bp@kh3Ohv{hsGfy
> zl#6oN+y`7_3%Z59Ma)4t2p^pZLVdxsIunyXFcTG_&U=3>fy5Pcee8;Oquy+9aUz=d
> zI1x!jQ`xEF2sGkx1QLx#v!lhjH^DH+htfg6<T<u%OW#uu8K%Gmios8dNp;RgWkJ=I
> za863h!IC9FphTc#1_5Gem;uJfyed&LLV&0c2oMMm2oMMm2oMOYVgxpFHzK~2*SW7F
> z>6Fdf%}6X|tzJMzVe5sFyN0>`(%-sr{ut}@vS?$h;<u2Px|Ik#ohMdyuvE>BSqtVz
> zv9z7}9&GZ6IJa0e`VatER;zkPAI>e|J#Xx$H=D(>O%2{dkDR%iPH0x6VUvr}AgDNi
> z0N3xC^#Fu}Ajr at 0g>0YzNQI)qgq1Cna6qT~_|WG_JG9TY(&@Qv0YJbffu9Zn(C&zk
> z;&=cs)*?Uv1oruB5I}Y#JLSUC#RcDVG>C*yR~iD(hSyWc<h^hQ0`4x8?bm()<vbMq
> zJjb9c#3s&yU#`8QUz#g}g8~D7&7|A8)9uyicIU*~cV^}0?=4ofw0Cs(Uc5XsJUTZ1
> z>Af!>T7SS`AJ4io*JaZh;QOFrN`rnU6yF0CCp74HLGk at hF}Fd#18O~pW<6Fuy31x6
> ztgJvS*)vYd%qwa>bFNQwP5Xs8ePy9CI~(d074boR*gj$^5KajZF)C(@#X`WF;voW5
> zz!r#ki*|iIJE}FBJJ%gSDM{QUB#jcujYMK7*=MoW{66%*bNX_*T;f>ExetFK=iWg>
> zB0<7^bqme_ck6|S<U{VZV?9)G4)^mp_mU;!++W25Fvy<Exi at HMtiG6Yk0OR1I_|sU
> z8aoI38TLB>*PdBR#diWnXz>8!+|#CChNED*agU3@^`}y)084stcXtO^(u<Y#4N&y1
> zFI&>V8Z)kO)L!aW)Z1<}_wDZW?!&WDnrT1R{7;>HHrH-k at 9v(Q?CxE^-k1(!+{T*P
> zs@%#YCT+<Qu|bq9343wcAPoTQfM3uG4>Gv)2NIr+!}9odBv2hd1_MK6F!&=GJRGwF
> zj|KL?dE6evZgl{No1KH>;)Fo-LLfjOu<8()<;<Jn-2dkvfBo*;Z~q8U(edyx&i%80
> z{r%669{mm4%yI4o0v<=l*`J#F_m7Lu!?%cYkL^0>IQI+ErkVB}7He at dQwxmX-0Q9|
> zZ_Qq4u0qw4`zMBMd!3F$rbBDVb8PJz^6fEwft33|aTa!?d;FpC6~=7M)aS*}_RWa4
> zU0tcnl!SeAUE8IuRpv?f+H2}F$}&k3KTtcOxu{agBzzz2|HN+H4rT!8(56->cS+cj
> z!<y5ogR%?>Uo)!imB}P&e3teTb*oY?N#N5khw(eX!2oY2Q)VhNCvRxFRSMY-$!5(B
> z)frj2NXX|xhc;!2-eKZSFcVDP(wtLO!hT=V4r at MC)ygCifkvz9k{uFlV|d^rye-So
> zg`~X$Lz=v<=~5q2$z|KLS2P#YjnFwwb5qqRs}zYC-r6zs`*=vcSV*_;GME5PwMTPG
> ztx)B|kksm9sxqZSb4A at FlZ)c{VUssC7gRN}-Fz>d12YJlL#z6*sz{jz51vz1%eG6x
> zU?81Jg(Q{FoV=zvt16eJivlo*Pwy}xN>{a=>Izk!QaCvV4^}91WhpSs^AO88J_?U^
> ztE*&*B2V1m9-M<UVuPppL`asrfdonfN at fsP2}{Gw)ClvcMWAEkz@^ys&<5|y^P1mw
> z2~P#rdLB4*Cg~`%%&TyH((Q};PHt8D at 82jnKXT|&LR(maw_;?tNS$)})!%s^Jk^`o
> z9DbN4b58rbzoa#;K2YwNryAbX!$0j?OOZA7=XG<BqY6sl*yXY_aqlwADZB0tNZVrT
> z{YyOZY6o|n3vKYKe5GJuxaz~WW=8GCVpUh#vG7A~yEkmR-e1_drH=NtTh3?Kl>_Nr
> z!AIQXnk$M6(T(&<%AUr~^y9or56ODb)xkaQ^WXKAyXEz1q&>n at GzF61KUkp_9HW=H
> zNJe|gn-gnUa`%k;AEz|2YCMZvcJ~kO?@ekAI7}_-7&ve)wlS!hT5zdT+7P1%+3%X#
> zclqGi=%fDS)V#C(1)cFteif9w_CD!Z!Eyfz*W8oMyWio-=sA?Qk%5Ztw3Cb~kA16l
> z;Sdui5Lf{SEc6K+ at HtqsVgirhhJ3yY{sfM|zySCMpT0r!_w%FsWdfUd0>^wlyq<Eu
> zcG33h=Z~SM+^<`-F-*Wum<R++A~26~|8!0>O9>x~-EK}8tF8KC&OP>s7!E6hf#3YL
> zISuFBV-Lh(Olu)CnyuLI=j$+nu)F<upf;u1`g*4Ugfwbb;^YI%?sTQ6i+wn7taqXr
> zCkGnN$%h<#f0!^nzCH;cS3kjl`FohYhUu&6^tG+en}`qY3qnr3J><k^bzHt at iW5Hy
> zWiBV)8rxE1Y>sQMxBr at adu(iibC2(Jy=+Es?q3!;!p~+Auw>8J9M9g+ZnG0yU|<C2
> MeyM*opWpxg0S16$b^rhX
>
> literal 0
> HcmV?d00001
>
> diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
> index 3625938e38..37b9ca268b 100644
> --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
> +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
> @@ -39,6 +39,7 @@ ipq40xx_setup_interfaces()
> mikrotik,cap-ac|\
> netgear,wac510|\
> sony,ncp-hg100-cellular|\
> + wallys,dr40x9|\
> zte,mf18a|\
> zte,mf289f)
> ucidef_set_interfaces_lan_wan "lan" "wan"
> diff --git a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches
> index 4918e2ccc1..f76fe9402d 100644
> --- a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches
> +++ b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches
> @@ -32,6 +32,9 @@ mikrotik,hap-ac3-lte6-kit)
> sony,ncp-hg100-cellular)
> ucidef_add_gpio_switch "uart_dbgcon_en" "debug console enable" "427" "1"
> ;;
> +wallys,dr40x9)
> + ucidef_add_gpio_switch "sim_card_select" "SIM card select" "423" "0"
> + ;;
> zte,mf286d|\
> zte,mf289f)
> ucidef_add_gpio_switch "power_btn_block" "Power button blocker" "421" "0"
> diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
> index 2012213a56..988921fa8c 100644
> --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
> @@ -119,7 +119,8 @@ platform_do_upgrade() {
> netgear,wac510 |\
> p2w,r619ac-64m |\
> p2w,r619ac-128m |\
> - qxwlan,e2600ac-c2)
> + qxwlan,e2600ac-c2 |\
> + wallys,dr40x9)
> nand_do_upgrade "$1"
> ;;
> glinet,gl-b2200)
> diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq40x9-dr40x9.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq40x9-dr40x9.dts
> new file mode 100644
> index 0000000000..e71f783387
> --- /dev/null
> +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq40x9-dr40x9.dts
> @@ -0,0 +1,425 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +
> +#include "qcom-ipq4019.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/soc/qcom,tcsr.h>
> +
> +/ {
> + model = "Wallystech DR40X9";
> + compatible = "wallys,dr40x9";
> +
> + aliases {
> + ethernet1 = &swport5;
> + };
You can remove this as MAC is passed as NVMEM cell.
> +
> + chosen {
> + bootargs-append = " ubi.mtd=ubi root=/dev/ubiblock0_1";
> + };
> +
> + soc {
> + rng at 22000 {
> + status = "okay";
> + };
> +
> + mdio at 90000 {
> + status = "okay";
> +
> + pinctrl-0 = <&mdio_pins>;
> + pinctrl-names = "default";
> + reset-gpios = <&tlmm 41 GPIO_ACTIVE_LOW>;
> + reset-delay-us = <2000>;
> + };
Please use the existing label for RNG and MDIO instead of putting them in soc.
> +
> + counter at 4a1000 {
> + compatible = "qcom,qca-gcnt";
> + reg = <0x4a1000 0x4>;
> + };
> +
> + tcsr at 1949000 {
> + compatible = "qcom,tcsr";
> + reg = <0x1949000 0x100>;
> + qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
> + };
> +
> + tcsr at 194b000 {
> + status = "okay";
> +
> + /* select hostmode */
> + compatible = "qcom,tcsr";
> + reg = <0x194b000 0x100>;
> + qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
> + };
> +
> + ess_tcsr at 1953000 {
> + compatible = "qcom,tcsr";
> + reg = <0x1953000 0x1000>;
> + qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
> + };
> +
> + tcsr at 1957000 {
> + compatible = "qcom,tcsr";
> + reg = <0x1957000 0x100>;
> + qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
> + };
> +
> + usb2: usb2 at 60f8800 {
> + status = "okay";
> + };
> +
> + usb3: usb3 at 8af8800 {
> + status = "okay";
> + };
> +
> + crypto at 8e3a000 {
> + status = "okay";
> + };
> +
> + watchdog at b017000 {
> + status = "okay";
> + };
Please use the existing labels for crypto, WDT, and USB nodes instead
of putting them in soc.
Regards,
Robert
> + };
> +
> + keys {
> + compatible = "gpio-keys";
> +
> + reset {
> + label = "reset";
> + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_RESTART>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + wlan2g {
> + label = "dr4029:green:wlan2g";
> + gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "phy0tpt";
> + };
> +
> + wlan5g {
> + label = "dr4029:green:wlan5g";
> + gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "phy1tpt";
> + };
> +
> + wlan2g-strength {
> + label = "dr4029:green:wlan2g-strength";
> + gpios = <&tlmm 36 GPIO_ACTIVE_LOW>;
> + };
> +
> + wlan5g-strength {
> + label = "dr4029:green:wlan5g-strength";
> + gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> +
> +&tlmm {
> + mdio_pins: mdio_pinmux {
> + mux_1 {
> + pins = "gpio6";
> + function = "mdio";
> + bias-pull-up;
> + };
> + mux_2 {
> + pins = "gpio7";
> + function = "mdc";
> + bias-pull-up;
> + };
> + };
> +
> + serial0_pins: serial0_pinmux {
> + mux {
> + pins = "gpio16", "gpio17";
> + function = "blsp_uart0";
> + bias-disable;
> + };
> + };
> +
> + serial1_pins: serial1_pinmux {
> + mux {
> + pins = "gpio8", "gpio9";
> + function = "blsp_uart1";
> + bias-disable;
> + };
> + };
> +
> + spi_0_pins: spi_0_pinmux {
> + pinmux {
> + function = "blsp_spi0";
> + pins = "gpio13", "gpio14", "gpio15";
> + drive-strength = <12>;
> + bias-disable;
> + };
> + pinmux_cs {
> + function = "gpio";
> + pins = "gpio12";
> + drive-strength = <2>;
> + bias-disable;
> + output-high;
> + };
> + };
> +
> + nand_pins: nand_pins {
> + pullups {
> + pins = "gpio52", "gpio53", "gpio58", "gpio59";
> + function = "qpic";
> + bias-pull-up;
> + };
> +
> + pulldowns {
> + pins = "gpio54", "gpio55", "gpio56", "gpio57",
> + "gpio60", "gpio62", "gpio63", "gpio64",
> + "gpio65", "gpio66", "gpio67", "gpio68",
> + "gpio69";
> + function = "qpic";
> + bias-pull-down;
> + };
> + };
> +
> + sd_pins: sd_pins {
> + pinmux {
> + function = "sdio";
> + pins = "gpio23", "gpio24", "gpio25", "gpio26",
> + "gpio28", "gpio29", "gpio30", "gpio31";
> + drive-strength = <10>;
> + };
> + pinmux_sd_clk {
> + function = "sdio";
> + pins = "gpio27";
> + drive-strength = <16>;
> + };
> + pinmux_sd7 {
> + function = "sdio";
> + pins = "gpio32";
> + drive-strength = <10>;
> + bias-disable;
> + };
> + };
> +};
> +
> +&blsp_dma {
> + status = "okay";
> +};
> +
> +&blsp1_spi1 {
> + status = "okay";
> +
> + pinctrl-0 = <&spi_0_pins>;
> + pinctrl-names = "default";
> +
> + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
> +
> + flash at 0 {
> + compatible = "jedec,spi-nor";
> + spi-max-frequency = <24000000>;
> + reg = <0>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition0 at 0 {
> + label = "0:SBL1";
> + reg = <0x00000000 0x00040000>;
> + read-only;
> + };
> +
> + partition1 at 40000 {
> + label = "0:MIBIB";
> + reg = <0x00040000 0x00020000>;
> + read-only;
> + };
> +
> + partition2 at 60000 {
> + label = "0:QSEE";
> + reg = <0x00060000 0x00060000>;
> + read-only;
> + };
> +
> + partition3 at c0000 {
> + label = "0:CDT";
> + reg = <0x000c0000 0x00010000>;
> + read-only;
> + };
> +
> + partition4 at d0000 {
> + label = "0:DDRPARAMS";
> + reg = <0x000d0000 0x00010000>;
> + read-only;
> + };
> +
> + partition5 at e0000 {
> + label = "0:APPSBLENV"; /* uboot env */
> + reg = <0x000e0000 0x00010000>;
> + read-only;
> + };
> +
> + partition6 at f0000 {
> + label = "0:APPSBL"; /* uboot */
> + reg = <0x000f0000 0x00080000>;
> + read-only;
> + };
> +
> + partition7 at 170000 {
> + label = "0:ART";
> + reg = <0x00170000 0x00010000>;
> + read-only;
> + compatible = "nvmem-cells";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + precal_art_1000: precal at 1000 {
> + reg = <0x1000 0x2f20>;
> + };
> +
> + precal_art_5000: precal at 5000 {
> + reg = <0x5000 0x2f20>;
> + };
> +
> + macaddr_art_0: mac-address at 0 {
> + reg = <0x0 0x6>;
> + };
> +
> + macaddr_art_6: mac-address at 6 {
> + reg = <0x6 0x6>;
> + };
> +
> + macaddr_art_1006: mac-address at 1006 {
> + reg = <0x1006 0x6>;
> + };
> +
> + macaddr_art_5006: mac-address at 5006 {
> + reg = <0x5006 0x6>;
> + };
> +
> + };
> +
> + partition8 at 180000 {
> + label = "0:CONFIG";
> + reg = <0x00180000 0x00010000>;
> + read-only;
> + };
> + };
> + };
> +};
> +
> +&qpic_bam {
> + status = "okay";
> +};
> +
> +&nand {
> + status = "okay";
> +
> + pinctrl-0 = <&nand_pins>;
> + pinctrl-names = "default";
> +
> + nand at 0 {
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition at 0 {
> + label = "ubi";
> + reg = <0x00000000 0x04000000>;
> + };
> + };
> + };
> +};
> +
> +&blsp1_uart1 {
> + status = "okay";
> +
> + pinctrl-0 = <&serial0_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&blsp1_uart2 {
> + status = "okay";
> +
> + pinctrl-0 = <&serial1_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&cryptobam {
> + num-channels = <4>;
> + qcom,num-ees = <2>;
> +
> + status = "okay";
> +};
> +
> +&pcie0 {
> + status = "okay";
> +
> + perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
> + wake-gpio = <&tlmm 40 GPIO_ACTIVE_LOW>;
> +
> + /* Unpolulated slot */
> + bridge at 0,0 {
> + reg = <0x00000000 0 0 0 0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + ranges;
> + };
> +};
> +
> +&vqmmc {
> + status = "okay";
> +};
> +
> +&sdhci {
> + pinctrl-0 = <&sd_pins>;
> + pinctrl-names = "default";
> + cd-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
> + vqmmc-supply = <&vqmmc>;
> + status = "okay";
> +};
> +
> +&gmac {
> + status = "okay";
> +};
> +&switch {
> + status = "okay";
> +};
> +&swport4 {
> + status = "okay";
> + label = "wan";
> + nvmem-cells = <&macaddr_art_0>;
> + nvmem-cell-names = "mac-address";
> +};
> +&swport5 {
> + status = "okay";
> + label = "lan";
> + nvmem-cells = <&macaddr_art_6>;
> + nvmem-cell-names = "mac-address";
> +};
> +&wifi0 {
> + status = "okay";
> + nvmem-cells = <&precal_art_1000>, <&macaddr_art_1006>;
> + nvmem-cell-names = "pre-calibration", "mac-address";
> + qcom,ath10k-calibration-variant = "Wallys-DR40X9";
> +};
> +
> +&wifi1 {
> + status = "okay";
> + nvmem-cell-names = "pre-calibration", "mac-address";
> + nvmem-cells = <&precal_art_5000>, <&macaddr_art_5006>;
> + qcom,ath10k-calibration-variant = "Wallys-DR40X9";
> +};
> +
> +&usb3_ss_phy {
> + status = "okay";
> +};
> +
> +&usb3_hs_phy {
> + status = "okay";
> +};
> +
> +&usb2_hs_phy {
> + status = "okay";
> +};
> diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk
> index a0ad63cfce..159a2dadbc 100644
> --- a/target/linux/ipq40xx/image/generic.mk
> +++ b/target/linux/ipq40xx/image/generic.mk
> @@ -1120,6 +1120,19 @@ endef
> # Missing DSA Setup
> #TARGET_DEVICES += unielec_u4019-32m
>
> +define Device/wallys_dr40x9
> + $(call Device/FitImage)
> + $(call Device/UbiFit)
> + DEVICE_VENDOR := Wallys
> + DEVICE_MODEL := DR40X9
> + SOC := qcom-ipq40x9
> + DEVICE_DTS_CONFIG := config at ap.dk07.1-c1
> + BLOCKSIZE := 128k
> + PAGESIZE := 2048
> + DEVICE_PACKAGES := ipq-wifi-wallys_dr40x9
> +endef
> +TARGET_DEVICES += wallys_dr40x9
> +
> define Device/zte_mf18a
> $(call Device/FitImage)
> DEVICE_VENDOR := ZTE
> --
> 2.34.1
>
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list