[PATCH] ipq40xx: add support for GL.iNet GL-B2200
Li Zhang
li.zhang at gl-inet.com
Mon Sep 13 01:02:00 PDT 2021
This patch adds supports for GL-B2200.
Specifications:
- SOC: Qualcomm IPQ4019 ARM Quad-Core
- RAM: 512 MiB
- Flash: 16 MiB NOR - SPI0
- EMMC: 8GB EMMC
- ETH: Qualcomm QCA8075
- WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2
- WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2
- WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2
- INPUT: Reset, WPS
- LED: Power, Internet
- UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
- UART2: On board with BLE module
- SPI1: On board socket for Zigbee module
Update firmware instructions
============================
Pleae update firmware on uboot web(default 192.168.1.1).
Signed-off-by: Li Zhang <li.zhang at gl-inet.com>
---
package/firmware/ipq-wifi/Makefile | 2 +
.../ipq-wifi/board-glinet_gl-b2200.qca4019 | Bin 0 -> 24308 bytes
.../ipq-wifi/board-glinet_gl-b2200.qca9888 | Bin 0 -> 12200 bytes
target/linux/ipq40xx/Makefile | 2 +-
.../ipq40xx/base-files/etc/board.d/02_network | 5 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 3 +
.../arch/arm/boot/dts/qcom-ipq4019-gl-b2200.dts | 364 +++++++++++++++++++++
target/linux/ipq40xx/image/generic.mk | 27 ++
.../patches-5.4/901-arm-boot-add-dts-files.patch | 3 +-
9 files changed, 404 insertions(+), 2 deletions(-)
create mode 100644 package/firmware/ipq-wifi/board-glinet_gl-b2200.qca4019
create mode 100644 package/firmware/ipq-wifi/board-glinet_gl-b2200.qca9888
create mode 100644 target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-gl-b2200.dts
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index e3b25bb..c7a388e 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -39,6 +39,7 @@ ALLWIFIBOARDS:= \
engenius_emr3500 \
ezviz_cs-w3-wd1200g-eup \
glinet_gl-ap1300 \
+ glinet_gl-b2200 \
glinet_gl-s1300 \
linksys_ea8300 \
linksys_mr8300-v0 \
@@ -124,6 +125,7 @@ $(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1))
$(eval $(call generate-ipq-wifi-package,engenius_emr3500,EnGenius EMR3500))
$(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP))
$(eval $(call generate-ipq-wifi-package,glinet_gl-ap1300,GL.iNet GL-AP1300))
+$(eval $(call generate-ipq-wifi-package,glinet_gl-b2200,GL.iNet GL-B2200))
$(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300))
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
$(eval $(call generate-ipq-wifi-package,linksys_mr8300-v0,Linksys MR8300))
diff --git a/package/firmware/ipq-wifi/board-glinet_gl-b2200.qca4019 b/package/firmware/ipq-wifi/board-glinet_gl-b2200.qca4019
new file mode 100644
index 0000000000000000000000000000000000000000..ac1850160aead29cee0fb96664272b8a620a4e6a
GIT binary patch
literal 24308
zcmeHPdr(tX8b1jj>SE!BfCzXAAv{7MK%g2V@)iT6U{R3(i$E30tx+C^hoKAYC{l=s
zKrI*|Xc?48Q$)ta7qM7dJEP40v48CBA8ltJ-I;aQcC<U~%<kfzdy at +xB$^0pdE76Y
zbG~!#_nq^d-#tn0&G~WPN{9=N+an4KO%0AukIP5|GMNlODGtGN0JgwXC@<e$P+S;P
zD3b=iT`VmLmLAw1O4JIE7L*;ptNhTQih?p}!I5LzcZ!4K`TWpOnT!T~S+E~gh^UxG
z12(mch)lfCz#f?81F+uS2`T_E0eCH(&`f7sE*tL(fbj6}AD=#@37Koa&woA>Lna&8
z!7IvLW4{*NNZ>gXcuZf at TlE@SlXXWzx%bckIO$*H5j;jxpDANrJ>r>8pthc<;p4LO
zFWA5$8ub~IVOWb{+S}XP+1c3`2mp8RnOZ0=(9STq!n$Fyu$yT!M<~;kWv-Mo58=y3
zFS92zKBQ`@KA4 at FEEvD0YO9uI?@5jyA5fiYER(*Kyk&e4YUR?5<TrkXa{o)NKN$Z+
z)mUAaoeU2St6Hk1*}IaX$NO<J*d~AuO^ub=;^Zj8;emf37{97I4M%u0Idc3{=ztLp
zeXx__>{LMj?5?%CBs)V8s(0|89p6i8)lgnyGW#&)FdGlkwUvO9>6tCB*50Oq%E*KM
znVzW=ZDqAdGTwfd_&Woook^zx%G~lh2Xi_jPqE6K3;G%h<dKDbyEiA_ZaGr3LmHIh
z68%Mg^+)Nac;%blzByRg`DRmarDxIT>Ef#BgWOCc@)op9#CSQ*(U<$A9iqn9D?N&D
zd{WUJQtMUXoWHzKqM{`cu(MzHs|}8bv&+U!9-GMze1j7IjD3;7e&7WWp3&)a8lKzO
zz^~;sda=J!mlf*v;N4w(l*93Xf4*#QZy&Zdo1JO9*65mq42dci5rM3%j5Ide3y$#9
zPfx#}n!>Mu1YBPqUE6=Y|KoRtZMflP2Yb4$?SG-2BRpX<{?DF0d91Tt#BhnOONQX}
z2-Heyn}_g(HwNk at 0E!<6m!+u at 6EMmU6hY$9I3x at WLrUbwYfpU8+}1Hy0Ybgpwn|~3
z3?Abl193;)dG2B-)CqAz<I#9t{KI%81x?|lh-1-MM1=BDK9B#9k8DG?@wSOW(NIKy
zP6wgBWLlk$Nhq9-ic;sCA4?!{MxCEHBOa&+&qJJmCOk<%QqfdisyG}Ce-e&Fp;5dj
zvF;=o=EP7s=odZ5mu<-h>LJ7AJ5MqAYB8xAy;bH_T?yBu)Eq2X0u)LVN at ftCmWCN%
zW;L%$lx877RVV}~1SkY31SkY31XeKu8~Ga%FUC&(P9&YNmA at 5<VXP$uWE8eu8o6hf
zlehlXm2<~fN6LbYv5HS2HFYZycs56@>|n9X at vQ|*#8Nv;`dUIZ;@o28=pz7NS*7e5
zePmn)2Et#z;m_Y}7NxC343^MRG#N at PK!Edi+&TclfFI=NctJK02U4NfFyUnjBMh+F
zo}O$YX@~7|TiNW~HVzO9XyC`A0JPg9wAcs$0 at flx2!yuzYY;$pp|8({rIQn}>1Z-0
zs&Qo?@O;>TNv9uxI}mVpnQpuGBPbW4kh2?uGM_ea7W{DS8U4y!>F?*u`6ZKX=T5g*
zr`w$q at 7j}<n}48K+0x$8)zf=rXn1t&&S&?(dSv|pgMB>fu3VRmH6Zpu#f%1WCzRL&
z6~{M_yP(AWr<mVB?toekqFIlXkM6Qr1}iI2OZJS at GV_X>&t2%#T-SbSPG4E5%*=*4
z#Y8+&PoAfk2@<Cg5iu&}iN%Q^Vk!a=qC%cf9I;^c*E6G9qq*{35tNa{PeRfdTlia$
zXh!yV{57`^@_UXfm&+}VwS4=q7xL|+ at 6%|IY+uzvu)ke;AR76Qw{2es6 at tJ0V!pj(
z(fIb)hyV<-7xL{5>}IPk=i8%*p@)w5ZokIH&UTvl4#4&2*3$4z^6d==!vB}SKo)@K
z&tx(Io=9<Zbp?1L#mf2yD5UGFmTa)bjB6~jhxt3^T^E+?F4sEO;h8AS*c&(hLnogb
zx6iJ3bxlro^*A`prozm&v8J{vw{fXSTe3u!AWD{my)ZUN0|2|>2ejOc4le(mMx=UJ
z)_+R_RUA4P7@~v0AL!uGm<@O$v;~fLY(dO+JAk;@*x4^k2vjc=0u%zP4uKiIyeYo@
zzyJQ1Z@>BG4-gd{2OsC#KmX_7{`C0qUtya$zP(Tw5vt?sPfh*nhlS_ho8sFC=>@0V
z<BWSYdjU254hHOb-kPZeM)B=+cbB(kZZcP)YRPXWhD>{%PC%wZYteIj?HY3Jaebb2
zdtY%@@$8!mqnfGri(%W>BieR#g(6cD^7Rd^N?oJKlL)le)#ntYk|cqzc0|*wRA3T;
zC;mTTx9|D~0O-)BmMiv3c$34Lv&y4bhD4wlRrg?+Bux;c{jIuHA(O-lSh&NT34eb;
zm|==cMdsv9O_x%R?UroS+*F>!%0!6*K6GeP93~ycC;Yi!^0wxJvI6$|hIUx<v9bn}
zNQ4@#QiUB8?FeuqMtBFy(S at X)fFVuZ(5Te!DP`CW?N!Ysbt806)7(;aVih7$fQNQW
z{UH&O7ar2xdjVVkr`oMKqn0c4VMuEANoA=*qPeQ>#$=*6LCEAS%_U_uwol-$bKv^n
zb7)l`R~9MK;K2*ZDr}b|1P0QnkV{ep+{x>j^U5+TUBtm1KAYe|l&)zz)#b`OMdIWb
zJXo&C#Zq9H7a^9h0u&zYQdeRLqD_RueK-eeWC>pCQz2P$0x6Uzl*}No5|)OUsZq_V
z7J-hDBbQ^^gBv_5E^2<QN<8CVv+2mOb4e$-rS63eNq2h>p5CtTIkZu7apc(L__mM+
z5BbP&kviq<>%Z|hdZs6{IqWzKb4>f9|8Q$;ov&<Do^p6^x8ST-4FhZF&+FpXqjE;!
z*p<?AvF~%s7<=yxNZVrSd=9(i)eP>v5ZvHi at mj&aaOKCb%>gwVi<PRhlVQhP_HEd4
zqrb3qTP^Dymz>XUC<fA1{_nZUG*{)9q8iy1jQx$B>Gcs6ZW0I4wZZ)#3f}jUx#aa}
zq}_>USaKx4f3RFFJjpI~l8knjH7C>r$y_rYe45e}RK2OlX<z^Fp`N5x&T(c@$H0*b
zF^zsz%!13E(uQbx;34PKzAH!1N1gB~W9FUjFX)VG at -AoOwf9NS3+sK#opVn&?|U}_
zW9KkpM+VBf(oP3dx*c4#3x}FGg}@3xV7^b^fX~315fgX}H{=VPh^KG(`f}hOeDVg%
z$J?9joe7rA(>LaF;Yqsv+6CLIpF0Lgw_mqlW0-)SYN8M at iNGAX{WBvoOUWJ!ZD$n5
zYOB7CZ%;g92LFwkO=%Pc|NnJB^6dQ}i>4P+hd2%}K^9Cb<lnFF<<{XTWn!izIP-K{
zJ!c-!5+PqdFp^Wc+TPbIVZJyY-WKxVvpTNaUkpC{Vq;{EXHT~Ol3aUyY>IDB>~+0r
mM)B=m6*<ap$s%CMp0PQOy<z*3o!~qJqxklV{jK at p{{IJ at zCWk{
literal 0
HcmV?d00001
diff --git a/package/firmware/ipq-wifi/board-glinet_gl-b2200.qca9888 b/package/firmware/ipq-wifi/board-glinet_gl-b2200.qca9888
new file mode 100644
index 0000000000000000000000000000000000000000..4f0a521f35935d4be1fb01b66dd9954a48eade52
GIT binary patch
literal 12200
zcmeHNT~HHO6uyZ%qC#Pp0P^Dsh-5(sVex0>pJ+8D3jzj85S3pID+VNxf)UhC)x=qn
z6hu*pVibldri{aMtZm0Sj1_0p=|dl!=}RB_?1Ob2UrKs6Vfj-usnGhfXLI+Sd+zzp
zx%b-*>~hH8log+)lqX6R at v?1M1)IVC{rdqFCV at QzPzqZ`lQylsvL;Sft*NSONK0H#
zR>oCT>uM^i)1=aM>*KUd71|bUWA*;{aSth!Db@*JXw{WB)Rb!))3#FaGJ=pw1u%X%
z%oU#S=Pv>Qy0)m<g0gu7{s2Ny20+snLUsuJ01zgzig3{awwo!Hm4FQeKvGiDv!_o5
z3XwN(I2;*VTOgW=aC`jwOizn5lYouym^nB5*w;BV^1vJJ#dUDL>>61;co}D5`;0|G
zrw9as1)Kmd<jnZy&D at w+*-~dvHgEX&F*OUTPmh){eK^zEov}zH0&L?XFfb6XjS~;Y
zK2SL5``)wn%%uGL-LydQ2+afBp^Il}URZJ`DDT5Fz%#%z;3)%rW&!XL2!sp0;0G%1
z;Hk1I#`5cLk6GWx4)&SqmO}&^dvN$hhs^QFQRY|*hCwepI9Upx!A`?g1bzD*9TWZ*
zi>^eeq_&X2&(G_r%bSc at y(%(tB^-zrKYuYc763JujWw?DUMyU=@NZ~a3?E)0zRZR9
z at ez*W_v|Sta at j&c{QX at q=ki=XSZ^AH0qYN&2HD2Oj+-K}v3N9wv4(d~dle4|h9Fs3
z7Ltf1BK1uN4}WDeb#}k3fYfpM(IW-LPzm|~MMAI;NeJbK`60_O877m+9>|bvEL)OI
zWn!6#93wD7LOdXlWGq>dOi3{*LShq(u-aa&POK?4bz)V#`qK4rhZ29x|A{{miiJu-
zsZH3XCz}ujrjRJ8BrNGk5|V<YNKz=*MVNYargBj~@8?(DyKie_OdY*9ZjL;he7l&g
zy(vCpr#n<SGJkoj-bQ!H)nwuFIA(x0sA|b<JkfehZ>06|0y6Uj6d=aMfccj0WC8dF
zeII>B)dB&r%yqh5RYxjtDPz-{>7#NbDRTmF7GR at Ks5E2_PB2$#GlVLauYnq)(vo at j
zI_q`)N&1j{`#2y*j05X{-lS5?Rd^iJPa7eW!V_T-Bg_DU*oPPsU8ho#NfS%5_A+L=
zo;6v&(HrPyxq?iFK at 9Xk`8G1me#zRdSJNeOi4zbbjs;d5(@7s-0n8=6iEfkUkm>fT
z3`1*Fg(PwNvh^6#NGs*IYY$>Eun#g8IGIOEVFn}JBF`o_+WVN}bPa2JG-&^tsikvN
zgbNUh1A9MQQUi>ZXuYCuhZ%Col-o9|QC~~%mXnYA>_&#B6)LF{5R1pW=`u~5=U-Q*
z(J{+_XK5B<rkQz`rqMCWfM;nIVt6ypz-t&db8&A+f^J1MlHb$yX>*)9xX?TG%hR75
z at Y>*=pJbowDK*OUE6M{3u3gl25<09B&A)y|(IVL!R_L?wO3%J_NnO}3KgBJZ#{AjQ
z at M@9rl8rv4I1!}@+Sz56>k{^cDSeWM&K+WswNVuTd0iJuPG%emt3<b->`|FAj;>UT
zRQ+9A;|5LSu0U$Uw$m727q%P8869e|=9&^(eU&}ERpyj7aXqTM*R3^B%@I2S6sOLq
z3~2|U-?owKx$O!1P&Ha|-d5h3d^q|5qC8~EZ(FrHFvlnT?D;AtQ@=(NQ270gmdgpp
zutvWM>xF7dYO7d-<}t>dEqG~Aw(rIhUB$=ACcMT!?}x!JtkPDj7Ts~DztWt3B&Go^
zywYCRCM{o)i=+&n)fsd3L at m12+_le`bug9=R=tK=eu`&+XW$)YVA0|w%Y1wh|A3(2
z(CP1GuF=~rf5=cq`i-{c5!mY0QSh at WG9r9cL_}mn5%6Lwqv5!e%#`O9m#OQUj~Fc7
zy#qrxe;yqj<<|1H`Q5<>5kbgGbStqH*@kW)HXs?O7bl>gqQiD$Wa^oF_4llQImZ%C
z<}8Ohd*yw223Q83KY#x0*|Wc<$P8ZG`g=9R%(dT)WqfQys#MJkKLh~w%}np`!<jt}
zB|17PDl(GScn<#i``}~yKJxpWWWX`xEm|n70>#|}cLng at -_Ag}1cmds3FU2UT%7sp
zsbcuUwRiabY`r*ob=3daT$MXlt<F`Qqw<u+rDauW#&W8=r}xUh;Lz~RpYGhf|IqV^
zDRn&0o?PD>Z{VzhQmBEeggR at Wl+3_YL7nwaiZE~$P|r!674hM-``+9JAJ#(MsTt=M
z?b>5HeWBm}-R*m`=^qv=le-a(iI6ZXOcF+kz~-^d2!&A+irNg;j;%#fu~bPawRX<l
muP3v5q6HFx2!?JUwjjCadSX42j+UHbkC$W2*YCagjQbD3Sk|Nf
literal 0
HcmV?d00001
diff --git a/target/linux/ipq40xx/Makefile b/target/linux/ipq40xx/Makefile
index 4006123..6bb5ded 100644
--- a/target/linux/ipq40xx/Makefile
+++ b/target/linux/ipq40xx/Makefile
@@ -3,7 +3,7 @@ include $(TOPDIR)/rules.mk
ARCH:=arm
BOARD:=ipq40xx
BOARDNAME:=Qualcomm Atheros IPQ40XX
-FEATURES:=squashfs fpu ramdisk nand
+FEATURES:=squashfs fpu ramdisk nand boot-part rootfs-part
CPU_TYPE:=cortex-a7
CPU_SUBTYPE:=neon-vfpv4
SUBTARGETS:=generic mikrotik
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index a675acc..c9ca20e 100644
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -101,6 +101,11 @@ ipq40xx_setup_interfaces()
ucidef_add_switch "switch0" \
"0u at eth0" "3:lan" "4:lan"
;;
+ glinet,gl-b2200)
+ ucidef_set_interfaces_lan_wan "eth0" "eth1"
+ ucidef_add_switch "switch0" \
+ "0u at eth0" "1:lan" "2:lan" "3:lan" "5:lan" "0u at eth1" "4:wan"
+ ;;
mobipromo,cm520-79f)
ucidef_add_switch "switch0" \
"0u at eth0" "3:lan:2" "4:lan:1"
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 87876ad..36a199c 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -35,6 +35,7 @@ case "$FIRMWARE" in
caldata_extract "ART" 0x9000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x32)
;;
+ glinet,gl-b2200 |\
engenius,eap2200 |\
openmesh,a62 |\
plasmacloud,pa2200)
@@ -57,6 +58,7 @@ case "$FIRMWARE" in
ezviz,cs-w3-wd1200g-eup |\
glinet,gl-ap1300 |\
glinet,gl-b1300 |\
+ glinet,gl-b2200 |\
glinet,gl-s1300 |\
linksys,ea6350v3 |\
mobipromo,cm520-79f |\
@@ -170,6 +172,7 @@ case "$FIRMWARE" in
ezviz,cs-w3-wd1200g-eup |\
glinet,gl-ap1300 |\
glinet,gl-b1300 |\
+ glinet,gl-b2200 |\
glinet,gl-s1300 |\
linksys,ea6350v3 |\
mobipromo,cm520-79f |\
diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-gl-b2200.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-gl-b2200.dts
new file mode 100644
index 0000000..f258e35
--- /dev/null
+++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-gl-b2200.dts
@@ -0,0 +1,364 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "GL.iNet GL-B2200";
+ compatible = "glinet,gl-b2200";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>;
+ };
+
+ chosen {
+ bootargs-append = " root=/dev/mmcblk0p2 rw rootwait clk_ignore_unused";
+ };
+
+ soc {
+ rng at 22000 {
+ status = "okay";
+ };
+
+ mdio at 90000 {
+ status = "okay";
+ };
+
+ ess-psgmii at 98000 {
+ status = "okay";
+ };
+
+ tcsr at 1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr at 194b000 {
+ /* select hostmode */
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ status = "okay";
+ };
+
+ ess_tcsr at 1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr at 1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ crypto at 8e3a000 {
+ status = "okay";
+ };
+
+ ess-switch at c000000 {
+ status = "okay";
+ switch_lan_bmp = <0x2e>;
+ switch_wan_bmp = <0x10>;
+ };
+
+ edma at c080000 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ linux,input-type = <1>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ linux,input-type = <1>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power_blue {
+ label = "power:blue";
+ gpios = <&tlmm 57 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ internet_blue {
+ label = "internet:blue";
+ gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>;
+ };
+ power_white {
+ label = "power:white";
+ gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
+ };
+ internet_white {
+ label = "internet:white";
+ gpios = <&tlmm 66 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&gmac1 {
+ qcom,phy_mdio_addr = <3>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <2 0x10>;
+};
+
+&gmac0 {
+ vlan_tag = <1 0x2e>;
+};
+
+&vqmmc {
+ status = "okay";
+};
+
+&sdhci {
+ status = "okay";
+ pinctrl-0 = <&sd_pins>;
+ pinctrl-names = "default";
+ cd-gpios = <&tlmm 3 GPIO_ACTIVE_LOW>;
+ vqmmc-supply = <&vqmmc>;
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "SBL1";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "MIBIB";
+ reg = <0x40000 0x20000>;
+ read-only;
+ };
+
+ partition at 60000 {
+ label = "QSEE";
+ reg = <0x60000 0x60000>;
+ read-only;
+ };
+
+ partition at c0000 {
+ label = "CDT";
+ reg = <0xc0000 0x10000>;
+ read-only;
+ };
+
+ partition at d0000 {
+ label = "DDRPARAMS";
+ reg = <0xd0000 0x10000>;
+ read-only;
+ };
+
+ partition at e0000 {
+ label = "APPSBLENV";
+ reg = <0xe0000 0x10000>;
+ read-only;
+ };
+
+ partition at f0000 {
+ label = "APPSBL";
+ reg = <0xf0000 0x80000>;
+ read-only;
+ };
+
+ partition at 170000 {
+ label = "ART";
+ reg = <0x170000 0x10000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&blsp1_spi2 {
+ pinctrl-0 = <&spi_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ spidev1: spi at 0 {
+ compatible = "siliconlabs,si3210";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&blsp1_uart2 {
+ pinctrl-0 = <&serial_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ serial_1_pins: serial1_pinmux {
+ mux {
+ pins = "gpio8", "gpio9",
+ "gpio10", "gpio11";
+ function = "blsp_uart1";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pinmux {
+ function = "blsp_spi0";
+ pins = "gpio13", "gpio14", "gpio15";
+ };
+ pinmux_cs {
+ function = "gpio";
+ pins = "gpio12";
+ };
+ pinconf {
+ pins = "gpio13", "gpio14", "gpio15";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pinconf_cs {
+ pins = "gpio12";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ spi_1_pins: spi_1_pinmux {
+ mux {
+ pins = "gpio44", "gpio46", "gpio47";
+ function = "blsp_spi1";
+ bias-disable;
+ };
+ cs {
+ pins = "gpio45";
+ function = "gpio";
+ bias-pull-up;
+ };
+ reset {
+ pins = "gpio43";
+ function = "gpio";
+ output-high;
+ };
+ mux_2 {
+ pins = "gpio35";
+ function = "gpio";
+ output-high;
+ };
+ host_int {
+ pins = "gpio2";
+ function = "gpio";
+ input;
+ };
+ wake {
+ pins = "gpio48";
+ function = "gpio";
+ output-high;
+ };
+ };
+
+ sd_pins: sd_pins {
+ pinmux {
+ function = "sdio";
+ pins = "gpio23", "gpio24", "gpio25", "gpio26",
+ "gpio29", "gpio30", "gpio31", "gpio32";
+ drive-strength = <10>;
+ };
+
+ pinmux_sd_clk {
+ function = "sdio";
+ pins = "gpio27";
+ drive-strength = <16>;
+ };
+
+ pinmux_sd7 {
+ function = "sdio";
+ pins = "gpio28";
+ drive-strength = <10>;
+ bias-disable;
+ };
+ };
+
+};
+
+&pcie0 {
+ status = "okay";
+ perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+ bridge at 0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi2: wifi at 1,0 {
+ status = "okay";
+ compatible = "qcom,ath10k";
+ reg = <0x00010000 0 0 0 0>;
+ qcom,ath10k-calibration-variant = "GL-B2200";
+ };
+ };
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "GL-B2200";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "GL-B2200";
+};
diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk
index 18f5d23..b0d6cf5 100644
--- a/target/linux/ipq40xx/image/generic.mk
+++ b/target/linux/ipq40xx/image/generic.mk
@@ -81,6 +81,17 @@ define Build/qsdk-ipq-factory-nand-askey
@mv $@.new $@
endef
+define Build/qsdk-ipq-app-gpt
+ cp $@ $@.tmp 2>/dev/null || true
+ ptgen -g -o $@.tmp -a 1 -l 1024 \
+ -t 0x2e -N 0:HLOS -r -p 32M \
+ -t 0x83 -N rootfs -r -p 128M \
+ -N rootfs_data -p 512M \
+ -N user_data -p 6766M
+ cat $@.tmp >> $@
+ rm $@.tmp
+endef
+
define Build/SenaoFW
-$(STAGING_DIR_HOST)/bin/mksenaofw \
-n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \
@@ -506,6 +517,22 @@ define Device/glinet_gl-b1300
endef
TARGET_DEVICES += glinet_gl-b1300
+define Device/glinet_gl-b2200
+ $(call Device/FitImage)
+ DEVICE_VENDOR := GL.iNet
+ DEVICE_MODEL := GL-B2200
+ SOC := qcom-ipq4019
+ DEVICE_DTS_CONFIG := config at ap.dk04.1-c3
+ KERNEL_INITRAMFS_SUFFIX := -recovery.itb
+ IMAGES := sdcard.img.gz
+ IMAGE/sdcard.img.gz := qsdk-ipq-app-gpt |\
+ pad-to 1024k | append-kernel |\
+ pad-to 33792k | append-rootfs |\
+ append-metadata | gzip
+ DEVICE_PACKAGES := ipq-wifi-glinet_gl-b2200 kmod-fs-ext4 kmod-mmc kmod-spi-dev mkf2fs e2fsprogs kmod-fs-f2fs
+endef
+TARGET_DEVICES += glinet_gl-b2200
+
define Device/glinet_gl-s1300
$(call Device/FitImage)
DEVICE_VENDOR := GL.iNet
diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
index 0447fb6..9af5055 100644
--- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john at phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -837,11 +837,61 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -837,11 +837,62 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@@ -67,6 +67,7 @@ Signed-off-by: John Crispin <john at phrozen.org>
+ qcom-ipq4029-ap-303h.dtb \
+ qcom-ipq4029-ap-365.dtb \
+ qcom-ipq4029-gl-b1300.dtb \
++ qcom-ipq4019-gl-b2200.dtb \
+ qcom-ipq4029-gl-s1300.dtb \
+ qcom-ipq4029-mr33.dtb \
qcom-ipq8064-ap148.dtb \
--
2.7.4
More information about the openwrt-devel
mailing list