[PATCH] ath79: add support for TP-Link TL-WA1201 v2
balasr at iis.ee.ethz.ch
balasr at iis.ee.ethz.ch
Thu Sep 2 08:07:14 PDT 2021
From: Robert Balas <balasr at iis.ee.ethz.ch>
This device is a wireless access point working on the 2.4 GHz and 5 GHz
band, based on Qualcomm/Atheros QCA9563 + QCA9886.
Specification
- 775 MHz CPU
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- QCA9563: 2.4 GHz 3x3
- QCA9886: 5 GHz
- AR8033: 1x 1 Gbs Ethernet
- 4x LED, WPS factory reset and power button
- bare UART on PCB (accessible through testpoints)
Methods for Flashing:
- Apply factory image in OEM firmware web-gui. Wait a minute after the
progress bar completes and restart the device.
- Sysupgrade on top of existing OpenWRT image
- Solder wires onto UART testpoints and attach a terminal.
Boot the device and press enter to enter u-boot's menu. Then issue the
following commands
1. setenv serverip your-server-ip
setenv ipaddr your-device-ip
2. tftp 0x80060000 openwrt-squashfs.bin (Rembember output of size in
hex, henceforth "sizeinhex")
3. erase 0x9f030000 +"sizeinhex"
4. cp.b 0x80060000 0x9f030000 0x"sizeinhex"
5. reboot
Recover:
- U-boot serial console
Signed-off-by: Robert Balas <balasr at iis.ee.ethz.ch>
---
.../ath79/dts/qca9563_tplink_tl-wa1201-v2.dts | 148 ++++++++++++++++++
.../generic/base-files/etc/board.d/01_leds | 3 +-
.../generic/base-files/etc/board.d/02_network | 1 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 3 +-
target/linux/ath79/image/generic-tp-link.mk | 11 ++
tools/firmware-utils/src/tplink-safeloader.c | 45 +++++-
6 files changed, 208 insertions(+), 3 deletions(-)
create mode 100644 target/linux/ath79/dts/qca9563_tplink_tl-wa1201-v2.dts
diff --git a/target/linux/ath79/dts/qca9563_tplink_tl-wa1201-v2.dts b/target/linux/ath79/dts/qca9563_tplink_tl-wa1201-v2.dts
new file mode 100644
index 0000000000..066bde7866
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_tplink_tl-wa1201-v2.dts
@@ -0,0 +1,148 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca956x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "tplink,tl-wa1201-v2", "qca,qca9563";
+ model = "TP-Link TL-WA1201 v2";
+
+ aliases {
+ label-mac-device = ð0;
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ mdio-gpio0 = &mdio2;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "green:power";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ wlan2g {
+ label = "green:wlan2g";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ wlan5g {
+ label = "green:wlan5g";
+ gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ lan {
+ label = "green:lan";
+ gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "Reset button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+
+ wps {
+ label = "WPS button";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+
+ mdio2: mdio {
+ compatible = "virtual,mdio-gpio";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpios = <&gpio 3 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio 4 GPIO_ACTIVE_HIGH>; /* MDIO */
+
+ phy4: ethernet-phy at 4 {
+ reg = <4>;
+
+ eee-broken-100tx;
+ eee-broken-1000t;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+ð0 {
+ status = "okay";
+
+ phy-mode = "sgmii";
+ phy-handle = <&phy4>;
+
+ mtd-mac-address = <&info 0x8>;
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+ mtd-mac-address = <&info 0x8>;
+};
+
+&spi {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x000000 0x020000>;
+ read-only;
+ };
+
+ info: partition at 20000 {
+ label = "info";
+ reg = <0x020000 0x010000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x030000 0xce0000>;
+ };
+
+ partition at d10000 {
+ label = "tplink";
+ reg = <0xd10000 0x2e0000>;
+ read-only;
+ };
+
+ art: partition at ff0000 {
+ label = "art";
+ reg = <0xff0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 8715a57213..ffc6f3086e 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -19,7 +19,8 @@ glinet,gl-ar300m-lite|\
glinet,gl-ar300m16|\
pcs,cap324|\
tplink,cpe610-v1|\
-tplink,cpe610-v2)
+tplink,cpe610-v2|\
+tplink,tl-wa1201-v2)
ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0"
;;
alfa-network,n2q)
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index 9cec8d5098..e2c6f9feac 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -72,6 +72,7 @@ ath79_setup_interfaces()
tplink,re450-v2|\
tplink,re450-v3|\
tplink,re455-v1|\
+ tplink,tl-wa1201-v2|\
tplink,tl-wr902ac-v1|\
ubnt,bullet-ac|\
ubnt,bullet-m-ar7240|\
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index a01cd9f6f8..5ba1a7a8ff 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -229,7 +229,8 @@ case "$FIRMWARE" in
tplink,archer-c60-v2|\
tplink,archer-c60-v3|\
tplink,archer-c6-v2|\
- tplink,archer-c6-v2-us)
+ tplink,archer-c6-v2-us|\
+ tplink,tl-wa1201-v2)
caldata_extract "art" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) -1)
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk
index 16494b111f..b6755fe547 100644
--- a/target/linux/ath79/image/generic-tp-link.mk
+++ b/target/linux/ath79/image/generic-tp-link.mk
@@ -510,6 +510,17 @@ define Device/tplink_tl-mr6400-v1
endef
TARGET_DEVICES += tplink_tl-mr6400-v1
+define Device/tplink_tl-wa1201-v2
+ $(Device/tplink-safeloader-uimage)
+ SOC := qca9563
+ IMAGE_SIZE := 13184k
+ DEVICE_MODEL := TL-WA1201
+ DEVICE_VARIANT := v2
+ TPLINK_BOARD_ID := TL-WA1201-V2
+ DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
+endef
+TARGET_DEVICES += tplink_tl-wa1201-v2
+
define Device/tplink_tl-wdr3500-v1
$(Device/tplink-8mlzma)
SOC := ar9344
diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c
index bd4d4b562e..597c48b9d4 100644
--- a/tools/firmware-utils/src/tplink-safeloader.c
+++ b/tools/firmware-utils/src/tplink-safeloader.c
@@ -1619,6 +1619,48 @@ static struct device_info boards[] = {
.last_sysupgrade_partition = "file-system"
},
+ /** Firmware layout for the TL-WA1201 v2 */
+ {
+ .id = "TL-WA1201-V2",
+ .vendor = "",
+ .support_list =
+ "SupportList:\n"
+ "{product_name:TL-WA1201,product_ver:2.0.0,special_id:45550000}\n"
+ "{product_name:TL-WA1201,product_ver:2.0.0,special_id:55530000}\n",
+ .part_trail = 0x00,
+ .soft_ver = "soft_ver:1.0.1 Build 20200709 rel.66244\n",
+
+ .partitions = {
+ {"fs-uboot", 0x00000, 0x20000},
+ {"default-mac", 0x20000, 0x00200},
+ {"pin", 0x20200, 0x00100},
+ {"product-info", 0x20300, 0x00200},
+ {"device-id", 0x20500, 0x0fb00},
+ {"firmware", 0x30000, 0xce0000},
+ {"portal-logo", 0xd10000, 0x20000},
+ {"portal-back", 0xd30000, 0x200000},
+ {"soft-version", 0xf30000, 0x00200},
+ {"extra-para", 0xf30200, 0x00200},
+ {"support-list", 0xf30400, 0x00200},
+ {"profile", 0xf30600, 0x0fa00},
+ {"apdef-config", 0xf40000, 0x10000},
+ {"ap-config", 0xf50000, 0x10000},
+ {"redef-config", 0xf60000, 0x10000},
+ {"re-config", 0xf70000, 0x10000},
+ {"multidef-config", 0xf80000, 0x10000},
+ {"multi-config", 0xf90000, 0x10000},
+ {"clientdef-config", 0xfa0000, 0x10000},
+ {"client-config", 0xfb0000, 0x10000},
+ {"partition-table", 0xfc0000, 0x10000},
+ {"user-config", 0xfd0000, 0x10000},
+ {"certificate", 0xfe0000, 0x10000},
+ {"radio", 0xff0000, 0x10000},
+ {NULL, 0, 0}
+ },
+ .first_sysupgrade_partition = "os-image",
+ .last_sysupgrade_partition = "file-system",
+ },
+
/** Firmware layout for the TL-WA850RE v2 */
{
.id = "TLWA850REV2",
@@ -2995,7 +3037,8 @@ static void build_image(const char *output,
const uint8_t extra_para[2] = {0x01, 0x00};
parts[5] = make_extra_para(info, extra_para,
sizeof(extra_para));
- } else if (strcasecmp(info->id, "ARCHER-C6-V2") == 0) {
+ } else if (strcasecmp(info->id, "ARCHER-C6-V2") == 0 ||
+ strcasecmp(info->id, "TL-WA1201-V2") == 0) {
const uint8_t extra_para[2] = {0x00, 0x01};
parts[5] = make_extra_para(info, extra_para,
sizeof(extra_para));
--
2.32.0
More information about the openwrt-devel
mailing list