ath79: add Embedded Wireless Balin Platform

Catrinel Catrinescu cc at 80211.de
Tue Nov 30 08:06:18 PST 2021


Add the Embedded Wireless "Balin" platform, it is in ar71xx too
 SoC: QCA AR9344 or AR9350
 RAM: DDR2-RAM 64MBytes
 Flash: SPI-NOR 16MBytes
 WLAN: 2 x 2 MIMO 2.4 & 5 GHz IEEE802.11 a/b/g/n
 Ethernet: 3 x 10/100 Mb/s
 USB: 1 x USB2.0 Host/Device bootstrap-pin at power-up
 PCI-Express: 1 x lane PCIe 1.2
 UART: 1 x Normal, 1 x High-Speed
 JTAG: 1 x EJTAG
 GPIO: 10 x Input/Output multiplexed

The module comes already with the current vanilla OpenWrt firmware.
To update, use "sysupgrade" image directly in vendor firmware.

Signed-off-by: Catrinel Catrinescu <cc at 80211.de>

---
 .../dts/ar9344_embeddedwireless_balin.dts     | 136 ++++++++++++++++++
 .../generic/base-files/etc/board.d/02_network |   4 +
 target/linux/ath79/image/generic.mk           |   9 ++
 3 files changed, 149 insertions(+)
 create mode 100644 target/linux/ath79/dts/ar9344_embeddedwireless_balin.dts

diff --git a/target/linux/ath79/dts/ar9344_embeddedwireless_balin.dts b/target/linux/ath79/dts/ar9344_embeddedwireless_balin.dts
new file mode 100644
index 0000000000..a18f665341
--- /dev/null
+++ b/target/linux/ath79/dts/ar9344_embeddedwireless_balin.dts
@@ -0,0 +1,136 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9344.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Embedded Wireless Balin";
+	compatible = "embeddedwireless,balin", "qca,ar9344";
+
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	aliases {
+		led-boot = &led_system;
+		led-failsafe = &led_system;
+		led-running = &led_system;
+		led-upgrade = &led_system;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_system: system {
+			label = "green:system";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
+			debounce-interval = <60>;
+		};
+	};
+};
+
+&ref {
+	clock-frequency = <40000000>;
+};
+
+&spi {
+	status = "okay";
+
+	flash at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			uboot: partition at 0 {
+				label = "u-boot";
+				reg = <0x000000 0x040000>;
+				read-only;
+			};
+
+			partition at 40000 {
+				label = "u-boot-env";
+				reg = <0x040000 0x010000>;
+			};
+
+			partition at 50000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x050000 0xfa0000>;
+			};
+
+			art: partition at ff0000 {
+				label = "art";
+				reg = <0xff0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+/*
+&pcie {
+	status = "okay";
+
+	ath9k: wifi at 0,0 {
+		compatible = "pci168c,0030";
+		reg = <0x0000 0 0 0 0>;
+		nvmem-cells = <&macaddr_art_c>;
+		nvmem-cell-names = "mac-address";
+		qca,no-eeprom;
+		#gpio-cells = <2>;
+		gpio-controller;
+	};
+};
+*/
+&builtin_switch {
+
+	/delete-property/qca,phy4-mii-enable;
+};
+
+&eth1 {
+	status = "okay";
+
+	nvmem-cells = <&macaddr_art_1002>;
+	nvmem-cell-names = "mac-address";
+	mac-address-increment-byte = <3>;
+	mac-address-increment = <0x40>;
+
+	gmac-config {
+		device = <&gmac>;
+		switch-phy-swap = <0>;
+		switch-only-mode = <1>;
+	};
+};
+
+&wmac {
+	status = "okay";
+
+	mtd-cal-data = <&art 0x1000>;
+};
+
+&art {
+	compatible = "nvmem-cells";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	macaddr_art_1002: macaddr at 1002 {
+		reg = <0x1002 0x6>;
+	};
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index 01e364a8fe..8c09932bd7 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -265,6 +265,10 @@ ath79_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0 at eth0" "2:lan:4" "3:lan:3" "4:lan:2" "5:lan:1" "1:wan"
 		;;
+	embeddedwireless,balin)
+		ucidef_add_switch "switch0" \
+			"0 at eth0" "5:lan:1" "4:lan:2" "3:wan"
+		;;
 	embeddedwireless,dorin)
 		ucidef_add_switch "switch0" \
 			"0 at eth0" "1:wan" "2:lan:3" "3:lan:2"
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 39f616b010..c259db94af 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -1028,6 +1028,15 @@ define Device/elecom_wrc-300ghbk2-i
 endef
 TARGET_DEVICES += elecom_wrc-300ghbk2-i
 
+define Device/embeddedwireless_balin
+  SOC := ar9344
+  DEVICE_VENDOR := Embedded Wireless
+  DEVICE_MODEL := Balin
+  DEVICE_PACKAGES := kmod-usb-chipidea2
+  IMAGE_SIZE := 16000k
+endef
+TARGET_DEVICES += embeddedwireless_balin
+
 define Device/embeddedwireless_dorin
   SOC := ar9331
   DEVICE_VENDOR := Embedded Wireless
-- 
2.17.1



More information about the openwrt-devel mailing list