[PATCH 5/5] bcm27xx: add support for Raspberry Pi Zero 2
Stijn Tintel
stijn at linux-ipv6.be
Fri Nov 19 19:41:52 PST 2021
Updating the entire patchset from Raspberry Pi upstream would also add
the Raspberry Pi Zero 2 patch, but as that is a cumbersome process, just
import the required patch. Prefix it with 950 so it is clear that this
patch comes from the same source, but use a high number for the 2nd part
of the prefix so that it's clear the patch is not in the upstream order.
Signed-off-by: Stijn Tintel <stijn at linux-ipv6.be>
---
.../bcm27xx/base-files/etc/board.d/02_network | 1 +
target/linux/bcm27xx/base-files/etc/diag.sh | 1 +
target/linux/bcm27xx/image/Makefile | 18 +-
...0-9900-ARM-dts-Add-Pi-Zero-2-Support.patch | 229 ++++++++++++++++++
4 files changed, 243 insertions(+), 6 deletions(-)
create mode 100644 target/linux/bcm27xx/patches-5.10/950-9900-ARM-dts-Add-Pi-Zero-2-Support.patch
diff --git a/target/linux/bcm27xx/base-files/etc/board.d/02_network b/target/linux/bcm27xx/base-files/etc/board.d/02_network
index f279941e1e..b4d73bf967 100644
--- a/target/linux/bcm27xx/base-files/etc/board.d/02_network
+++ b/target/linux/bcm27xx/base-files/etc/board.d/02_network
@@ -23,6 +23,7 @@ raspberrypi,4-model-b)
ucidef_set_interface_lan "eth0"
;;
+raspberrypi,model-zero-2 |\
raspberrypi,model-zero-w)
ucidef_set_interface_lan "wlan0"
;;
diff --git a/target/linux/bcm27xx/base-files/etc/diag.sh b/target/linux/bcm27xx/base-files/etc/diag.sh
index f5e9ee0111..2a10aa9bdb 100644
--- a/target/linux/bcm27xx/base-files/etc/diag.sh
+++ b/target/linux/bcm27xx/base-files/etc/diag.sh
@@ -20,6 +20,7 @@ set_state() {
raspberrypi,3-compute-module |\
raspberrypi,model-b |\
raspberrypi,model-zero |\
+ raspberrypi,model-zero-2 |\
raspberrypi,model-zero-w)
status_led="led0"
;;
diff --git a/target/linux/bcm27xx/image/Makefile b/target/linux/bcm27xx/image/Makefile
index f0c3ae1272..3165a2d1e5 100644
--- a/target/linux/bcm27xx/image/Makefile
+++ b/target/linux/bcm27xx/image/Makefile
@@ -96,14 +96,17 @@ define Device/rpi-2
bcm2709-rpi-2-b bcm2710-rpi-2-b \
bcm2710-rpi-3-b bcm2710-rpi-3-b-plus \
bcm2711-rpi-4-b bcm2711-rpi-400 \
- bcm2710-rpi-cm3 bcm2711-rpi-cm4
+ bcm2710-rpi-cm3 bcm2711-rpi-cm4 \
+ bcm2710-rpi-zero-2
SUPPORTED_DEVICES := \
- rpi-2-b rpi-3-b rpi-3-b-plus rpi-cm \
+ rpi-2-b rpi-3-b rpi-3-b-plus rpi-cm rpi-zero-2 \
raspberrypi,2-model-b raspberrypi,2-model-b-rev2 \
raspberrypi,3-model-b raspberrypi,3-model-b-plus \
raspberrypi,3-compute-module raspberrypi,compute-module-3 \
- raspberrypi,400 raspberrypi,4-compute-module raspberrypi,4-model-b
+ raspberrypi,400 raspberrypi,4-compute-module raspberrypi,4-model-b \
+ raspberrypi,model-zero-2
DEVICE_PACKAGES := \
+ bcm43436-firmware \
cypress-firmware-43430-sdio \
cypress-nvram-43430-sdio-rpi-3b \
cypress-firmware-43455-sdio \
@@ -126,13 +129,16 @@ define Device/rpi-3
DEVICE_DTS := \
broadcom/bcm2710-rpi-2-b \
broadcom/bcm2710-rpi-3-b broadcom/bcm2710-rpi-3-b-plus \
- broadcom/bcm2710-rpi-cm3
+ broadcom/bcm2710-rpi-cm3 \
+ broadcom/bcm2710-rpi-zero-2
SUPPORTED_DEVICES := \
- rpi-3-b rpi-3-b-plus \
+ rpi-3-b rpi-3-b-plus rpi-zero-2 \
raspberrypi,2-model-b-rev2 \
raspberrypi,3-model-b raspberrypi,3-model-b-plus \
- raspberrypi,3-compute-module raspberrypi,compute-module-3
+ raspberrypi,3-compute-module raspberrypi,compute-module-3 \
+ raspberrypi,model-zero-2
DEVICE_PACKAGES := \
+ bcm43436-firmware \
cypress-firmware-43430-sdio \
cypress-nvram-43430-sdio-rpi-3b \
cypress-firmware-43455-sdio \
diff --git a/target/linux/bcm27xx/patches-5.10/950-9900-ARM-dts-Add-Pi-Zero-2-Support.patch b/target/linux/bcm27xx/patches-5.10/950-9900-ARM-dts-Add-Pi-Zero-2-Support.patch
new file mode 100644
index 0000000000..6c37045c80
--- /dev/null
+++ b/target/linux/bcm27xx/patches-5.10/950-9900-ARM-dts-Add-Pi-Zero-2-Support.patch
@@ -0,0 +1,229 @@
+From 84dc624be6ae704fdb3c413b7d86315cf49fbb0b Mon Sep 17 00:00:00 2001
+From: Phil Elwell <phil at raspberrypi.com>
+Date: Thu, 9 Sep 2021 10:37:15 +0100
+Subject: [PATCH] ARM: dts: Add Pi Zero 2 support
+
+Signed-off-by: Phil Elwell <phil at raspberrypi.com>
+---
+ arch/arm/boot/dts/Makefile | 1 +
+ arch/arm/boot/dts/bcm2710-rpi-zero-2.dts | 177 ++++++++++++++++++
+ arch/arm64/boot/dts/broadcom/Makefile | 1 +
+ .../boot/dts/broadcom/bcm2710-rpi-zero-2.dts | 1 +
+ 4 files changed, 180 insertions(+)
+ create mode 100644 arch/arm/boot/dts/bcm2710-rpi-zero-2.dts
+ create mode 100644 arch/arm64/boot/dts/broadcom/bcm2710-rpi-zero-2.dts
+
+diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
+index 12cd8bf582e1b..66956d0f2c187 100644
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
+ bcm2708-rpi-cm.dtb \
+ bcm2708-rpi-zero.dtb \
+ bcm2708-rpi-zero-w.dtb \
++ bcm2710-rpi-zero-2.dtb \
+ bcm2709-rpi-2-b.dtb \
+ bcm2710-rpi-2-b.dtb \
+ bcm2710-rpi-3-b.dtb \
+diff --git a/arch/arm/boot/dts/bcm2710-rpi-zero-2.dts b/arch/arm/boot/dts/bcm2710-rpi-zero-2.dts
+new file mode 100644
+index 0000000000000..42185a4506666
+--- /dev/null
++++ b/arch/arm/boot/dts/bcm2710-rpi-zero-2.dts
+@@ -0,0 +1,177 @@
++/dts-v1/;
++
++#include "bcm2710.dtsi"
++#include "bcm2709-rpi.dtsi"
++#include "bcm283x-rpi-csi1-2lane.dtsi"
++#include "bcm283x-rpi-i2c0mux_0_44.dtsi"
++#include "bcm2708-rpi-bt.dtsi"
++#include "bcm283x-rpi-cam1-regulator.dtsi"
++
++/ {
++ compatible = "raspberrypi,model-zero-2", "brcm,bcm2837";
++ model = "Raspberry Pi Zero 2";
++
++ chosen {
++ bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1";
++ };
++
++ aliases {
++ serial0 = &uart1;
++ serial1 = &uart0;
++ mmc1 = &mmcnr;
++ };
++};
++
++&gpio {
++ spi0_pins: spi0_pins {
++ brcm,pins = <9 10 11>;
++ brcm,function = <4>; /* alt0 */
++ };
++
++ spi0_cs_pins: spi0_cs_pins {
++ brcm,pins = <8 7>;
++ brcm,function = <1>; /* output */
++ };
++
++ i2c0_pins: i2c0 {
++ brcm,pins = <0 1>;
++ brcm,function = <4>;
++ };
++
++ i2c1_pins: i2c1 {
++ brcm,pins = <2 3>;
++ brcm,function = <4>;
++ };
++
++ i2s_pins: i2s {
++ brcm,pins = <18 19 20 21>;
++ brcm,function = <4>; /* alt0 */
++ };
++
++ sdio_pins: sdio_pins {
++ brcm,pins = <34 35 36 37 38 39>;
++ brcm,function = <7>; // alt3 = SD1
++ brcm,pull = <0 2 2 2 2 2>;
++ };
++
++ bt_pins: bt_pins {
++ brcm,pins = <43>;
++ brcm,function = <4>; /* alt0:GPCLK2 */
++ brcm,pull = <0>;
++ };
++
++ uart0_pins: uart0_pins {
++ brcm,pins = <30 31 32 33>;
++ brcm,function = <7>; /* alt3=UART0 */
++ brcm,pull = <2 0 0 2>; /* up none none up */
++ };
++
++ uart1_pins: uart1_pins {
++ brcm,pins;
++ brcm,function;
++ brcm,pull;
++ };
++
++ audio_pins: audio_pins {
++ brcm,pins = <>;
++ brcm,function = <>;
++ };
++};
++
++&mmcnr {
++ pinctrl-names = "default";
++ pinctrl-0 = <&sdio_pins>;
++ bus-width = <4>;
++ status = "okay";
++};
++
++&uart0 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&uart0_pins &bt_pins>;
++ status = "okay";
++};
++
++&uart1 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&uart1_pins>;
++ status = "okay";
++};
++
++&spi0 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
++
++ spidev0: spidev at 0{
++ compatible = "spidev";
++ reg = <0>; /* CE0 */
++ #address-cells = <1>;
++ #size-cells = <0>;
++ spi-max-frequency = <125000000>;
++ };
++
++ spidev1: spidev at 1{
++ compatible = "spidev";
++ reg = <1>; /* CE1 */
++ #address-cells = <1>;
++ #size-cells = <0>;
++ spi-max-frequency = <125000000>;
++ };
++};
++
++&i2c0if {
++ clock-frequency = <100000>;
++};
++
++&i2c1 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&i2c1_pins>;
++ clock-frequency = <100000>;
++};
++
++&i2c2 {
++ clock-frequency = <100000>;
++};
++
++&i2s {
++ pinctrl-names = "default";
++ pinctrl-0 = <&i2s_pins>;
++};
++
++&leds {
++ act_led: led-act {
++ label = "led0";
++ linux,default-trigger = "actpwr";
++ gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
++ };
++};
++
++&hdmi {
++ hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
++};
++
++&audio {
++ pinctrl-names = "default";
++ pinctrl-0 = <&audio_pins>;
++ brcm,disable-headphones = <1>;
++};
++
++&bt {
++ shutdown-gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
++};
++
++&minibt {
++ shutdown-gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
++};
++
++&cam1_reg {
++ gpio = <&gpio 40 GPIO_ACTIVE_HIGH>;
++};
++
++/ {
++ __overrides__ {
++ act_led_gpio = <&act_led>,"gpios:4";
++ act_led_activelow = <&act_led>,"gpios:8";
++ act_led_trigger = <&act_led>,"linux,default-trigger";
++ };
++};
+diff --git a/arch/arm64/boot/dts/broadcom/Makefile b/arch/arm64/boot/dts/broadcom/Makefile
+index 69809bf2f45df..e7c2c4fd59a87 100644
+--- a/arch/arm64/boot/dts/broadcom/Makefile
++++ b/arch/arm64/boot/dts/broadcom/Makefile
+@@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += bcm2837-rpi-3-a-plus.dtb \
+ bcm2837-rpi-3-b.dtb \
+ bcm2837-rpi-3-b-plus.dtb \
+ bcm2837-rpi-cm3-io3.dtb
++dtb-$(CONFIG_ARCH_BCM2835) += bcm2710-rpi-zero-2.dtb
+ dtb-$(CONFIG_ARCH_BCM2835) += bcm2710-rpi-2-b.dtb
+ dtb-$(CONFIG_ARCH_BCM2835) += bcm2710-rpi-3-b.dtb
+ dtb-$(CONFIG_ARCH_BCM2835) += bcm2710-rpi-3-b-plus.dtb
+diff --git a/arch/arm64/boot/dts/broadcom/bcm2710-rpi-zero-2.dts b/arch/arm64/boot/dts/broadcom/bcm2710-rpi-zero-2.dts
+new file mode 100644
+index 0000000000000..f76f553599ef2
+--- /dev/null
++++ b/arch/arm64/boot/dts/broadcom/bcm2710-rpi-zero-2.dts
+@@ -0,0 +1 @@
++#include "../../../../arm/boot/dts/bcm2710-rpi-zero-2.dts"
--
2.32.0
More information about the openwrt-devel
mailing list