[PATCH v2 2/2] ipq806x: add support for TP-Link Talon AD7200
Paul Fertser
fercerpav at gmail.com
Mon Jan 4 12:27:50 EST 2021
From: Gary Cooper <gaco at bitmessage.de>
Device hardware: https://deviwiki.com/wiki/TP-LINK_AD7200_(Talon)
The Talon AD7200 is basically an Archer C2600 with a third PCIe lane
and an 802.11ad radio. It looks like the Archers C2600/5400 but the
housing is slightly larger.
Specifications
--------------
- IPQ8064 dual-core 1400MHz
- QCA9988 2.4GHz WiFi
- QCA9990 5GHz WiFi
- QCA9500 60GHz WiFi
- 32MB SPI Flash
- 512MiB RAM
- 5 GBit Ports (QCA8337)
Installation
------------
Installation is possible from the OEM web interface.
Sysupgrade is possible.
TFTP recovery is possible.
- Image: AD7200_1.0_tp_recovery.bin
Notes
- This will be the first 802.11ad device supported by mainline.
Signed-off-by: Gary Cooper <gaco at bitmessage.de>
---
package/firmware/linux-firmware/qca.mk | 8 +
package/kernel/mac80211/ath.mk | 13 +-
.../ipq806x/base-files/etc/board.d/01_leds | 9 +
.../ipq806x/base-files/etc/board.d/02_network | 1 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 2 +
.../base-files/lib/upgrade/platform.sh | 1 +
.../arch/arm/boot/dts/qcom-ipq8064-ad7200.dts | 440 ++++++++++++++++++
target/linux/ipq806x/image/Makefile | 15 +
tools/firmware-utils/src/tplink-safeloader.c | 44 ++
9 files changed, 532 insertions(+), 1 deletion(-)
create mode 100644 target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ad7200.dts
diff --git a/package/firmware/linux-firmware/qca.mk b/package/firmware/linux-firmware/qca.mk
index 23fcc0905a..71b484d5c7 100644
--- a/package/firmware/linux-firmware/qca.mk
+++ b/package/firmware/linux-firmware/qca.mk
@@ -37,3 +37,11 @@ define Package/carl9170-firmware/install
$(INSTALL_DATA) $(PKG_BUILD_DIR)/carl9170-1.fw $(1)/lib/firmware
endef
$(eval $(call BuildPackage,carl9170-firmware))
+
+Package/wil6210-firmware = $(call Package/firmware-default,wil6210 firmware)
+define Package/wil6210-firmware/install
+ $(INSTALL_DIR) $(1)/lib/firmware
+ $(INSTALL_DATA) $(PKG_BUILD_DIR)/wil6210.fw $(1)/lib/firmware
+ $(INSTALL_DATA) $(PKG_BUILD_DIR)/wil6210.brd $(1)/lib/firmware
+endef
+$(eval $(call BuildPackage,wil6210-firmware))
diff --git a/package/kernel/mac80211/ath.mk b/package/kernel/mac80211/ath.mk
index 957c9da939..f8245e24e1 100644
--- a/package/kernel/mac80211/ath.mk
+++ b/package/kernel/mac80211/ath.mk
@@ -1,6 +1,6 @@
PKG_DRIVERS += \
ath ath5k ath6kl ath6kl-sdio ath6kl-usb ath9k ath9k-common ath9k-htc ath10k \
- carl9170 owl-loader ar5523
+ carl9170 wil6210 owl-loader ar5523
PKG_CONFIG_DEPENDS += \
CONFIG_PACKAGE_ATH_DEBUG \
@@ -20,6 +20,7 @@ ifdef CONFIG_PACKAGE_MAC80211_DEBUGFS
ATH9K_HTC_DEBUGFS \
ATH10K_DEBUGFS \
CARL9170_DEBUGFS \
+ WIL6210_DEBUGFS \
ATH5K_DEBUG \
ATH6KL_DEBUG
endif
@@ -29,6 +30,7 @@ ifdef CONFIG_PACKAGE_MAC80211_TRACING
ATH10K_TRACING \
ATH6KL_TRACING \
ATH_TRACEPOINTS \
+ WIL6210_TRACING \
ATH5K_TRACER
endif
@@ -66,6 +68,7 @@ config-$(call config_package,ath6kl-sdio) += ATH6KL_SDIO
config-$(call config_package,ath6kl-usb) += ATH6KL_USB
config-$(call config_package,carl9170) += CARL9170
+config-$(call config_package,wil6210) += WIL6210
config-$(call config_package,ar5523) += AR5523
define KernelPackage/ath/config
@@ -285,6 +288,14 @@ define KernelPackage/carl9170
AUTOLOAD:=$(call AutoProbe,carl9170)
endef
+define KernelPackage/wil6210
+ $(call KernelPackage/mac80211/Default)
+ TITLE:=QCA/Wilocity 60g WiFi card wil6210 support
+ DEPENDS+= @PCI_SUPPORT +kmod-mac80211 +wil6210-firmware
+ FILES:=$(PKG_BUILD_DIR)/drivers/net/wireless/ath/wil6210/wil6210.ko
+ AUTOLOAD:=$(call AutoProbe,wil6210)
+endef
+
define KernelPackage/owl-loader
$(call KernelPackage/mac80211/Default)
TITLE:=Owl loader for initializing Atheros PCI(e) Wifi chips
diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds
index fed821663a..a03a056d83 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds
@@ -39,6 +39,15 @@ netgear,r7800)
ucidef_set_led_switch "wan" "WAN" "white:wan" "switch0" "0x20"
ucidef_set_led_ide "esata" "eSATA" "white:esata"
;;
+tplink,ad7200)
+ ucidef_set_led_usbport "usb1" "USB 1" "blue:usb_1" "usb1-port1" "usb2-port1"
+ ucidef_set_led_usbport "usb2" "USB 2" "blue:usb_3" "usb3-port1" "usb4-port1"
+ ucidef_set_led_switch "wan" "wan" "blue:wan" "switch0" "0x02"
+ ucidef_set_led_switch "lan" "lan" "blue:lan" "switch0" "0x3c"
+ ucidef_set_led_wlan "wlan2g" "wlan2g" "blue:wlan2g" "phy2tpt"
+ ucidef_set_led_wlan "wlan5g" "wlan5g" "blue:wlan5g" "phy1tpt"
+ ucidef_set_led_netdev "wlan60g" "wlan60g" "blue:wlan60g" "wlan0"
+ ;;
tplink,c2600)
ucidef_set_led_usbport "usb1" "USB 1" "white:usb_2" "usb1-port1" "usb2-port1"
ucidef_set_led_usbport "usb2" "USB 2" "white:usb_4" "usb3-port1" "usb4-port1"
diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network
index 10b2ec0148..fbf56c5e0c 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
@@ -51,6 +51,7 @@ nec,wg2600hp3)
"2:lan" "3:lan" "4:lan" "5:lan" "0 at eth1" "1:wan" "6 at eth0"
;;
netgear,r7800 |\
+tplink,ad7200 |\
tplink,c2600)
ucidef_add_switch "switch0" \
"1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "6 at eth1" "5:wan" "0 at eth0"
diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 8788fc92f6..3befc40630 100644
--- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -35,6 +35,7 @@ case "$FIRMWARE" in
caldata_extract "art" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x6) +1)
;;
+ tplink,ad7200 |\
tplink,c2600)
caldata_extract "radio" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary default-mac 0x8) -1)
@@ -74,6 +75,7 @@ case "$FIRMWARE" in
caldata_extract "art" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x6) +2)
;;
+ tplink,ad7200 |\
tplink,c2600)
caldata_extract "radio" 0x5000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary default-mac 0x8)
diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
index f5d6c5d55d..4dc612492c 100644
--- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
@@ -43,6 +43,7 @@ platform_do_upgrade() {
linksys,ea8500)
platform_do_upgrade_linksys "$1"
;;
+ tplink,ad7200 |\
tplink,c2600)
PART_NAME="os-image:rootfs"
MTD_CONFIG_ARGS="-s 0x200000"
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ad7200.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ad7200.dts
new file mode 100644
index 0000000000..e5bdc32114
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8064-ad7200.dts
@@ -0,0 +1,440 @@
+//SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+#include "qcom-ipq8064-v2.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "TP-Link Talon AD7200";
+ compatible = "tplink,ad7200", "qcom,ipq8064";
+
+ memory at 0 {
+ reg = <0x42000000 0x1e000000>;
+ device_type = "memory";
+ };
+
+ aliases {
+ mdio-gpio0 = &mdio0;
+
+ led-boot = &power;
+ led-failsafe = &power;
+ led-running = &power;
+ led-upgrade = &power;
+ label-mac-device = &gmac2;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&button_pins>;
+ pinctrl-names = "default";
+
+ wifi {
+ label = "wifi";
+ gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&qcom_pinmux 7 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ ledgeneral {
+ label = "ledswitch";
+ gpios = <&qcom_pinmux 53 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_LIGHTS_TOGGLE>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&led_pins>;
+ pinctrl-names = "default";
+
+ lan {
+ label = "blue:lan";
+ gpios = <&qcom_pinmux 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ usb1 {
+ label = "blue:usb_1";
+ gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ usb3 {
+ label = "blue:usb_3";
+ gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
+ };
+
+ wps {
+ label = "blue:wps";
+ gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>;
+ };
+
+ wan_orange {
+ label = "orange:wan";
+ gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
+ };
+
+ wan_blue {
+ label = "blue:wan";
+ gpios = <&qcom_pinmux 33 GPIO_ACTIVE_LOW>;
+ };
+
+ power: status {
+ label = "blue:status";
+ gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan2g {
+ label = "blue:wlan2g";
+ gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>;
+
+ };
+
+ wlan5g {
+ label = "blue:wlan5g";
+ gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>;
+
+ };
+
+ wlan60g {
+ label = "blue:wlan60g";
+ gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&qcom_pinmux {
+ button_pins: button_pins {
+ mux {
+ pins = "gpio53", "gpio54", "gpio67";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ led_pins: led_pins {
+ mux {
+ pins = "gpio2", "gpio8", "gpio15", "gpio16", "gpio17", "gpio26",
+ "gpio33", "gpio55", "gpio56", "gpio66";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ bias-pull-down;
+ };
+
+ data {
+ pins = "gpio18", "gpio19";
+ drive-strength = <10>;
+ };
+
+ cs {
+ pins = "gpio20";
+ function = "gpio";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ clk {
+ pins = "gpio21";
+ drive-strength = <12>;
+ };
+ };
+
+ usb0_pwr_en_pin: usb0_pwr_en_pin {
+ mux {
+ pins = "gpio25";
+ function = "gpio";
+ drive-strength = <10>;
+ bias-pull-up;
+ output-high;
+ };
+ };
+
+ usb1_pwr_en_pin: usb1_pwr_en_pin {
+ mux {
+ pins = "gpio23";
+ function = "gpio";
+ drive-strength = <10>;
+ bias-pull-up;
+ output-high;
+ };
+ };
+};
+
+&gsbi5 {
+ qcom,mode = <GSBI_PROT_SPI>;
+ status = "okay";
+
+ spi4: spi at 1a280000 {
+ status = "okay";
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+ m25p80 at 0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+
+ SBL1 at 0 {
+ label = "SBL1";
+ reg = <0x0 0x20000>;
+ read-only;
+ };
+
+ MIBIB at 20000 {
+ label = "MIBIB";
+ reg = <0x20000 0x20000>;
+ read-only;
+ };
+
+ SBL2 at 40000 {
+ label = "SBL2";
+ reg = <0x40000 0x20000>;
+ read-only;
+ };
+
+ SBL3 at 60000 {
+ label = "SBL3";
+ reg = <0x60000 0x30000>;
+ read-only;
+ };
+
+ DDRCONFIG at 90000 {
+ label = "DDRCONFIG";
+ reg = <0x90000 0x10000>;
+ read-only;
+ };
+
+ SSD at a0000 {
+ label = "SSD";
+ reg = <0xa0000 0x10000>;
+ read-only;
+ };
+
+ TZ at b0000 {
+ label = "TZ";
+ reg = <0xb0000 0x30000>;
+ read-only;
+ };
+
+ RPM at e0000 {
+ label = "RPM";
+ reg = <0xe0000 0x20000>;
+ read-only;
+ };
+
+ fs-uboot at 100000 {
+ label = "fs-uboot";
+ reg = <0x100000 0x70000>;
+ read-only;
+ };
+
+ uboot-env at 170000 {
+ label = "uboot-env";
+ reg = <0x170000 0x40000>;
+ read-only;
+ };
+
+ radio at 1b0000 {
+ label = "radio";
+ reg = <0x1b0000 0x40000>;
+ read-only;
+ };
+
+ os-image at 1f0000 {
+ label = "os-image";
+ reg = <0x1f0000 0x400000>;
+ };
+
+ rootfs at 5f0000 {
+ label = "rootfs";
+ reg = <0x5f0000 0x1900000>;
+ };
+
+ defaultmac: default-mac at 1ef0000 {
+ label = "default-mac";
+ reg = <0x1ef0000 0x00200>;
+ read-only;
+ };
+
+ pin at 1ef0200 {
+ label = "pin";
+ reg = <0x1ef0200 0x00200>;
+ read-only;
+ };
+
+ device-id at 1ef0400 {
+ label = "device-id";
+ reg = <0x1ef0400 0x00200>;
+ read-only;
+ };
+
+ product-info at 1ef0600 {
+ label = "product-info";
+ reg = <0x1ef0600 0x0fa00>;
+ read-only;
+ };
+
+ partition-table at 1f00000 {
+ label = "partition-table";
+ reg = <0x1f00000 0x10000>;
+ read-only;
+ };
+
+ soft-version at 1f10000 {
+ label = "soft-version";
+ reg = <0x1f10000 0x10000>;
+ read-only;
+ };
+
+ support-list at 1f20000 {
+ label = "support-list";
+ reg = <0x1f20000 0x10000>;
+ read-only;
+ };
+
+ profile at 1f30000 {
+ label = "profile";
+ reg = <0x1f30000 0x10000>;
+ read-only;
+ };
+
+ default-config at 1f40000 {
+ label = "default-config";
+ reg = <0x1f40000 0x10000>;
+ read-only;
+ };
+
+ user-config at 1f50000 {
+ label = "user-config";
+ reg = <0x1f50000 0x40000>;
+ read-only;
+ };
+
+ qos-db at 1f90000 {
+ label = "qos-db";
+ reg = <0x1f90000 0x40000>;
+ read-only;
+ };
+
+ usb-config at 1fd0000 {
+ label = "usb-config";
+ reg = <0x1fd0000 0x10000>;
+ read-only;
+ };
+
+ log at 1fe0000 {
+ label = "log";
+ reg = <0x1fe0000 0x20000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&usb3_0 {
+ status = "okay";
+
+ pinctrl-0 = <&usb0_pwr_en_pin>;
+ pinctrl-names = "default";
+};
+
+&usb3_1 {
+ status = "okay";
+
+ pinctrl-0 = <&usb1_pwr_en_pin>;
+ pinctrl-names = "default";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+ max-link-speed = <1>;
+};
+
+&pcie2 {
+ status = "okay";
+ max-link-speed = <1>;
+};
+
+&mdio0 {
+ status = "okay";
+
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x00004 0x7600000 /* PAD0_MODE */
+ 0x00008 0x1000000 /* PAD5_MODE */
+ 0x0000c 0x80 /* PAD6_MODE */
+ 0x000e4 0x6a545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x4e /* PORT0_STATUS */
+ 0x00094 0x4e /* PORT6_STATUS */
+ >;
+ };
+
+ phy4: ethernet-phy at 4 {
+ reg = <4>;
+ };
+};
+
+&gmac1 {
+ status = "okay";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ mtd-mac-address = <&defaultmac 0x8>;
+ mtd-mac-address-increment = <1>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+
+ mtd-mac-address = <&defaultmac 0x8>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&adm_dma {
+ status = "okay";
+};
diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile
index 80bfec5ad9..876f337bba 100644
--- a/target/linux/ipq806x/image/Makefile
+++ b/target/linux/ipq806x/image/Makefile
@@ -333,6 +333,21 @@ define Device/qcom_ipq8064-db149
endef
TARGET_DEVICES += qcom_ipq8064-db149
+define Device/tplink_ad7200
+ $(call Device/TpSafeImage)
+ DEVICE_VENDOR := TP-Link
+ DEVICE_MODEL := Talon AD7200
+ DEVICE_VARIANT := v1
+ SOC := qcom-ipq8064
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ BOARD_NAME := ad7200
+ SUPPORTED_DEVICES += ad7200
+ TPLINK_BOARD_ID := AD7200
+ DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct kmod-wil6210
+endef
+TARGET_DEVICES += tplink_ad7200
+
define Device/tplink_c2600
$(call Device/TpSafeImage)
DEVICE_VENDOR := TP-Link
diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c
index deba84c6d1..785ff39642 100644
--- a/tools/firmware-utils/src/tplink-safeloader.c
+++ b/tools/firmware-utils/src/tplink-safeloader.c
@@ -668,6 +668,50 @@ static struct device_info boards[] = {
.last_sysupgrade_partition = "support-list",
},
+ /** Firmware layout for the AD7200 */
+ {
+ .id = "AD7200",
+ .vendor = "",
+ .support_list =
+ "SupportList:\r\n"
+ "{product_name:Talon AD7200,product_ver:1.0.0,special_id:00000000}\r\n",
+ .part_trail = 0x00,
+ .soft_ver = NULL,
+
+ .partitions = {
+ {"SBL1", 0x00000, 0x20000},
+ {"MIBIB", 0x20000, 0x20000},
+ {"SBL2", 0x40000, 0x20000},
+ {"SBL3", 0x60000, 0x30000},
+ {"DDRCONFIG", 0x90000, 0x10000},
+ {"SSD", 0xa0000, 0x10000},
+ {"TZ", 0xb0000, 0x30000},
+ {"RPM", 0xe0000, 0x20000},
+ {"fs-uboot", 0x100000, 0x70000},
+ {"uboot-env", 0x170000, 0x40000},
+ {"radio", 0x1b0000, 0x40000},
+ {"os-image", 0x1f0000, 0x400000},
+ {"file-system", 0x5f0000, 0x1900000},
+ {"default-mac", 0x1ef0000, 0x00200},
+ {"pin", 0x1ef0200, 0x00200},
+ {"device-id", 0x1ef0400, 0x00200},
+ {"product-info", 0x1ef0600, 0x0fa00},
+ {"partition-table", 0x1f00000, 0x10000},
+ {"soft-version", 0x1f10000, 0x10000},
+ {"support-list", 0x1f20000, 0x10000},
+ {"profile", 0x1f30000, 0x10000},
+ {"default-config", 0x1f40000, 0x10000},
+ {"user-config", 0x1f50000, 0x40000},
+ {"qos-db", 0x1f90000, 0x40000},
+ {"usb-config", 0x1fd0000, 0x10000},
+ {"log", 0x1fe0000, 0x20000},
+ {NULL, 0, 0}
+ },
+
+ .first_sysupgrade_partition = "os-image",
+ .last_sysupgrade_partition = "file-system"
+ },
+
/** Firmware layout for the C2600 */
{
.id = "C2600",
--
2.20.1
More information about the openwrt-devel
mailing list