[RFC PATCH 2/5] ath79: add support for MikroTik RouterBOARD 960PGS (hEx PoE)
Oskari Lemmela
oskari at lemmela.net
Sun Dec 26 10:41:23 PST 2021
This patch adds support for the MikroTik RouterBOARD 960PGS (hEx PoE)
router. The device has a USB 2.0 port and a SFP port for adding optical
fiber connectivity. The ports 2-5 can power other PoE capable devices
with the same voltage as applied to the unit.
Specifications:
- SoC: Qualcomm Atheros QCA9557
- Flash: 16 MB (SPI)
- RAM: 128 MB
- 1x Ethernet SFP: 1000
- 1x Ethernet RJ45: 10/100/1000 port with passive POE in
- 4x Ethernet RJ45: 10/100/1000 ports with 802.3af/at PoE out
- 1x USB 2.0 host port
- 1x reset button
See https://mikrotik.com/product/RB960PGS for more details.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Oskari Lemmela <oskari at lemmela.net>
---
.../qca9557_mikrotik_routerboard-960pgs.dts | 279 ++++++++++++++++++
target/linux/ath79/image/mikrotik.mk | 9 +
.../base-files/etc/board.d/02_network | 14 +
.../lib/preinit/10_rename_interfaces.sh | 11 +
4 files changed, 313 insertions(+)
create mode 100644 target/linux/ath79/dts/qca9557_mikrotik_routerboard-960pgs.dts
create mode 100644 target/linux/ath79/mikrotik/base-files/lib/preinit/10_rename_interfaces.sh
diff --git a/target/linux/ath79/dts/qca9557_mikrotik_routerboard-960pgs.dts b/target/linux/ath79/dts/qca9557_mikrotik_routerboard-960pgs.dts
new file mode 100644
index 0000000000..273357cf39
--- /dev/null
+++ b/target/linux/ath79/dts/qca9557_mikrotik_routerboard-960pgs.dts
@@ -0,0 +1,279 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca955x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "mikrotik,routerboard-960pgs", "qca,qca9557";
+ model = "MikroTik RouterBOARD 960PGS";
+
+ aliases {
+ serial0 = &uart;
+ };
+
+ gpio_export {
+ compatible = "gpio-export";
+ #size-cells = <0>;
+
+ buzzer {
+ /* Beeper requires PWM for frequency selection */
+ gpio-export,name = "buzzer";
+ gpio-export,output = <0>;
+ gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ i2c: i2c {
+ compatible = "i2c-gpio";
+
+ i2c-gpio,delay-us = <5>;
+ i2c-gpio,timeout-ms = <1>;
+ sda-gpios = <&gpio 18 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio 19 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+
+ sfp_eeprom at 50 {
+ compatible = "at,24c04";
+ reg = <0x50>;
+ };
+
+ sfp_eeprom at 51 {
+ compatible = "at,24c04";
+ reg = <0x51>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ debounce-interval = <60>;
+ gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_user: user {
+ label = "green:user";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ };
+
+ led_sfp: sfp {
+ label = "green:sfp";
+ gpios = <&gpio 2 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ sfp1: sfp {
+ compatible = "sff,sfp";
+
+ i2c-bus = <&i2c>;
+ maximum-power-milliwatt = <1000>;
+ los-gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ tx-disable-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb_vbus {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "usb_vbus";
+ gpio = <&gpio 13 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ switch at 0 {
+ compatible = "qca,qca8337";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ label = "cpu";
+ ethernet = <ð0>;
+ phy-mode = "rgmii-id";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+ label = "lan1";
+ phy-mode = "internal";
+ phy-handle = <&phy_port1>;
+ };
+
+ port at 2 {
+ reg = <2>;
+ label = "lan2";
+ phy-mode = "internal";
+ phy-handle = <&phy_port2>;
+ };
+
+ port at 3 {
+ reg = <3>;
+ label = "lan3";
+ phy-mode = "internal";
+ phy-handle = <&phy_port3>;
+ };
+
+ port at 4 {
+ reg = <4>;
+ label = "lan4";
+ phy-mode = "internal";
+ phy-handle = <&phy_port4>;
+ };
+
+ port at 5 {
+ reg = <5>;
+ label = "lan5";
+ phy-mode = "internal";
+ phy-handle = <&phy_port5>;
+ };
+ };
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy_port1: phy at 0 {
+ reg = <0>;
+ };
+
+ phy_port2: phy at 1 {
+ reg = <1>;
+ };
+
+ phy_port3: phy at 2 {
+ reg = <2>;
+ };
+
+ phy_port4: phy at 3 {
+ reg = <3>;
+ };
+
+ phy_port5: phy at 4 {
+ reg = <4>;
+ };
+ };
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ pll-data = <0x8f000000 0xa0000101 0xa0001313>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&mdio1 {
+ status = "okay";
+
+ phy_sfp: ethernet-phy at 0 {
+ reg = <0>;
+ phy-mode = "sgmii";
+ sfp = <&sfp1>;
+ };
+};
+
+ð1 {
+ status = "okay";
+
+ phy-handle = <&phy_sfp>;
+ pll-data = <0x03000000 0x00000101 0x00001616>;
+ qca955x-sgmii-fixup;
+
+ gmac-config {
+ device = <&gmac>;
+ };
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&spi {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ compatible = "mikrotik,routerboot-partitions";
+ label = "RouterBoot";
+ reg = <0x0 0x20000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "bootloader1";
+ reg = <0x0 0x0>;
+ read-only;
+ };
+
+ hard_config {
+ read-only;
+ };
+
+ bios {
+ size = <0x1000>;
+ read-only;
+ };
+
+ partition at 10000 {
+ label = "bootloader2";
+ reg = <0x10000 0x0>;
+ read-only;
+ };
+
+ soft_config {
+ label = "soft_config";
+ };
+ };
+
+ partition at 20000 {
+ compatible = "mikrotik,minor";
+ label = "firmware";
+ reg = <0x020000 0xfe0000>;
+ };
+ };
+ };
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb_phy0 {
+ status = "okay";
+};
diff --git a/target/linux/ath79/image/mikrotik.mk b/target/linux/ath79/image/mikrotik.mk
index 095a1cbc84..44ea708f48 100644
--- a/target/linux/ath79/image/mikrotik.mk
+++ b/target/linux/ath79/image/mikrotik.mk
@@ -38,6 +38,15 @@ define Device/mikrotik_routerboard-922uags-5hpacd
endef
TARGET_DEVICES += mikrotik_routerboard-922uags-5hpacd
+define Device/mikrotik_routerboard-960pgs
+ $(Device/mikrotik_nor)
+ SOC := qca9557
+ DEVICE_MODEL := RouterBOARD 960PGS (hEX PoE)
+ IMAGE_SIZE := 16256k
+ DEVICE_PACKAGES += kmod-usb2 kmod-i2c-gpio kmod-sfp
+endef
+TARGET_DEVICES += mikrotik_routerboard-960pgs
+
define Device/mikrotik_routerboard-lhg-2nd
$(Device/mikrotik_nor)
SOC := qca9533
diff --git a/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network b/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network
index 4058742133..91a62e33c3 100644
--- a/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network
@@ -14,6 +14,9 @@ ath79_setup_interfaces()
ucidef_add_switch "switch1" \
"0 at eth1" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3"
;;
+ mikrotik,routerboard-960pgs)
+ ucidef_set_interface_lan "sfp lan1 lan2 lan3 lan4 lan5"
+ ;;
mikrotik,routerboard-912uag-2hpnd|\
mikrotik,routerboard-lhg-2nd|\
mikrotik,routerboard-sxt-5nd-r2|\
@@ -50,6 +53,17 @@ ath79_setup_macs()
lan_mac="$mac_base"
wan_mac=$(macaddr_add $mac_base 1)
;;
+ mikrotik,routerboard-960pgs)
+ label_mac=$mac_base
+ ucidef_set_bridge_device switch
+ ucidef_set_bridge_mac "$mac_base"
+ ucidef_set_network_device_mac "sfp" "$mac_base"
+ ucidef_set_network_device_mac "lan1" "$(macaddr_add $mac_base 1)"
+ ucidef_set_network_device_mac "lan2" "$(macaddr_add $mac_base 2)"
+ ucidef_set_network_device_mac "lan3" "$(macaddr_add $mac_base 3)"
+ ucidef_set_network_device_mac "lan4" "$(macaddr_add $mac_base 4)"
+ ucidef_set_network_device_mac "lan5" "$(macaddr_add $mac_base 5)"
+ ;;
*)
label_mac="$mac_base"
wan_mac="$mac_base"
diff --git a/target/linux/ath79/mikrotik/base-files/lib/preinit/10_rename_interfaces.sh b/target/linux/ath79/mikrotik/base-files/lib/preinit/10_rename_interfaces.sh
new file mode 100644
index 0000000000..66e7e24e5d
--- /dev/null
+++ b/target/linux/ath79/mikrotik/base-files/lib/preinit/10_rename_interfaces.sh
@@ -0,0 +1,11 @@
+. /lib/functions.sh
+
+set_interface_names() {
+ case $(board_name) in
+ mikrotik,routerboard-960pgs)
+ ip link set dev eth1 name sfp
+ ;;
+ esac
+}
+
+boot_hook_add preinit_main set_interface_names
--
2.25.1
More information about the openwrt-devel
mailing list