[OpenWrt-Devel] [PATCH] ath79: add support for gl-e750
koen.vandeputte at ncentric.com
Wed May 27 10:01:16 EDT 2020
On 27.05.20 15:33, Koen Vandeputte wrote:
> On 07.05.20 13:46, Luochongjun wrote:
>> The gl-e750 is a portable travel router that gives you safe access to
>> the internet while traveling.
>> - SoC: Qualcomm Atheros AR9531 (650MHz)
>> - RAM: 128 MB DDR2
>> - Flash: 16 MB SPI NOR (W25Q128FVSG) + 128 MB SPI NAND (GD5F1GQ4UFYIG)
>> - Ethernet: 10/100: 1xLAN
>> - Wireless: QCA9531 2.4GHz (bgn) + QCA9887 5GHz (ac)
>> - USB: 1x USB 2.0 port
>> - Switch: 1x switch
>> - Button: 1x reset button
>> - OLED Screen: 128*64 px
>> Flash instruction:
>> Support for sysupgrade directive upgrades, as well as luci upgrades.
> I retested this patch just to be sure I didn't miss anything before.
> Did you test this patch on actual hardware before sending this?
> I've got 2x e750-Mudi devices which:
> - I first flashed to the latest Gl.inet firmware (18.06 based) (works
> - Tried sysupgrade --> results in platform_check failure
> - Tried forced sysupgrade --> does not boot afterwards
> - Tried uboot recovery (both sysupgrade and factory images) --> does
> not boot
> Using gl.inet official img, the uboot recovery mode works fine.
I just soldered UART to the board.
Ethernet is not coming up properly.
[ 0.551090] libphy: Fixed MDIO Bus: probed
[ 0.872975] ag71xx 19000000.eth: Could not connect to PHY device.
[ 0.881098] ag71xx 1a000000.eth: invalid MAC address, using random
[ 1.139873] random: fast init done
[ 1.520295] libphy: ag71xx_mdio: probed
[ 1.525811] libphy: ar8xxx-mdio: probed
[ 1.538905] switch0: Atheros AR8229 rev. 1 switch registered on mdio.0
[ 1.587451] ag71xx 1a000000.eth: connected to PHY at fixed-0:00
[uid=00000000, driver=Generic PHY]
[ 1.597499] eth0: Atheros AG71xx at 0xba000000, irq 5, mode: gmii
[ 1.605610] NET: Registered protocol family 10
[ 1.614929] Segment Routing with IPv6
[ 1.618900] NET: Registered protocol family 17
[ 1.623601] 8021q: 802.1Q VLAN Support v1.8
[ 1.631247] PCI host bridge /ahb/pcie-controller at 180c0000 ranges:
[ 1.637642] MEM 0x0000000010000000..0x0000000013ffffff
[ 1.643057] IO 0x0000000000000000..0x0000000000000000
[ 1.648655] PCI host bridge to bus 0000:00
[ 1.652937] pci_bus 0000:00: root bus resource [mem
[ 1.660051] pci_bus 0000:00: root bus resource [io 0x0000]
[ 1.665824] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 1.672845] pci_bus 0000:00: No busn resource found for root bus,
will use [bus 00-ff]
[ 1.682374] pci 0000:00:00.0: BAR 0: assigned [mem
[ 1.690010] pci 0000:00:00.0: BAR 6: assigned [mem
[ 2.013961] ag71xx 19000000.eth: connected to PHY at mdio.0:1f:04
[uid=004dd042, driver=Generic PHY]
[ 2.024473] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode: mii
[ 10.293731] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 11.325088] eth0: link up (1000Mbps/Full duplex)
[ 11.329934] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 17.716093] eth0: link down
this device also only has 1 ethernet port exposed on the board.
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
More information about the openwrt-devel