[OpenWrt-Devel] [PATCH 2/2] ipq40xx: 5.4: fix ethernet driver

Robert Marko robert.marko at sartura.hr
Tue Mar 3 14:19:31 EST 2020


In 5.4 kernel old u32 array way of setting network features was dropped and linkmode is now the only way.
So lets migrate the EDMA driver to support linkmode.
Also, old get/set settings API for ethtool is also dropped so lets convert to new ksettings API while at it as it demands linkmode.

Now, gigabit works properly as well as ethtool.
Previously you would get this in ethtool:
root at OpenWrt:/# ethtool eth1
Settings for eth1:
        Supports Wake-on: d
        Wake-on: d
        Current message level: 0x00000000 (0)

        Link detected: yes

Now, features are properly advertised:
root at OpenWrt:/# ethtool eth1
Settings for eth1:
        Supported ports: [ TP MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  10baseT/Half 10baseT/Full
                                             100baseT/Half 100baseT/Full
                                             1000baseT/Full
        Link partner advertised pause frame use: No
        Link partner advertised auto-negotiation: No
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 4
        Transceiver: internal
        Auto-negotiation: on
        MDI-X: Unknown
        Supports Wake-on: d
        Wake-on: d
        Current message level: 0x00000000 (0)

        Link detected: yes

Signed-off-by: Robert Marko <robert.marko at sartura.hr>
---
 .../ethernet/qualcomm/essedma/edma_ethtool.c  | 65 ++++++++++---------
 1 file changed, 36 insertions(+), 29 deletions(-)

diff --git a/target/linux/ipq40xx/files-5.4/drivers/net/ethernet/qualcomm/essedma/edma_ethtool.c b/target/linux/ipq40xx/files-5.4/drivers/net/ethernet/qualcomm/essedma/edma_ethtool.c
index 8f6e3833b6..1270e20a90 100644
--- a/target/linux/ipq40xx/files-5.4/drivers/net/ethernet/qualcomm/essedma/edma_ethtool.c
+++ b/target/linux/ipq40xx/files-5.4/drivers/net/ethernet/qualcomm/essedma/edma_ethtool.c
@@ -180,9 +180,8 @@ static uint32_t edma_get_msglevel(struct net_device *netdev)
 /* edma_get_settings()
  *	Get edma settings
  */
-#if 0
 static int edma_get_settings(struct net_device *netdev,
-			     struct ethtool_cmd *ecmd)
+			     struct ethtool_link_ksettings *cmd)
 {
 	struct edma_adapter *adapter = netdev_priv(netdev);
 
@@ -196,38 +195,46 @@ static int edma_get_settings(struct net_device *netdev,
 
 		phydev = adapter->phydev;
 
-		ecmd->advertising = phydev->advertising;
-		ecmd->autoneg = phydev->autoneg;
+		linkmode_copy(cmd->link_modes.advertising, phydev->advertising);
+		linkmode_copy(cmd->link_modes.supported, phydev->supported);
+
+		cmd->base.autoneg = phydev->autoneg;
 
 		if (adapter->link_state == __EDMA_LINKDOWN) {
-			ecmd->speed =  SPEED_UNKNOWN;
-			ecmd->duplex = DUPLEX_UNKNOWN;
+			cmd->base.speed =  SPEED_UNKNOWN;
+			cmd->base.duplex = DUPLEX_UNKNOWN;
 		} else {
-			ecmd->speed = phydev->speed;
-			ecmd->duplex = phydev->duplex;
+			cmd->base.speed = phydev->speed;
+			cmd->base.duplex = phydev->duplex;
 		}
 
-		ecmd->phy_address = adapter->phy_mdio_addr;
+		cmd->base.phy_address = adapter->phy_mdio_addr;
 
 		phyreg = (uint16_t)phy_read(adapter->phydev, MII_LPA);
 		if (phyreg & LPA_10HALF)
-			ecmd->lp_advertising |= ADVERTISED_10baseT_Half;
+			linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT_Half_BIT, 
+								cmd->link_modes.lp_advertising);
 
 		if (phyreg & LPA_10FULL)
-			ecmd->lp_advertising |= ADVERTISED_10baseT_Full;
+			linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, 
+								cmd->link_modes.lp_advertising);
 
 		if (phyreg & LPA_100HALF)
-			ecmd->lp_advertising |= ADVERTISED_100baseT_Half;
+			linkmode_set_bit(ETHTOOL_LINK_MODE_100baseT_Half_BIT, 
+								cmd->link_modes.lp_advertising);
 
 		if (phyreg & LPA_100FULL)
-			ecmd->lp_advertising |= ADVERTISED_100baseT_Full;
+			linkmode_set_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT, 
+								cmd->link_modes.lp_advertising);
 
 		phyreg = (uint16_t)phy_read(adapter->phydev, MII_STAT1000);
 		if (phyreg & LPA_1000HALF)
-			ecmd->lp_advertising |= ADVERTISED_1000baseT_Half;
+			linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseT_Half_BIT, 
+								cmd->link_modes.lp_advertising);
 
 		if (phyreg & LPA_1000FULL)
-			ecmd->lp_advertising |= ADVERTISED_1000baseT_Full;
+			linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT, 
+								cmd->link_modes.lp_advertising);
 	} else {
 		/* If the speed/duplex for this GMAC is forced and we
 		 * are not polling for link state changes, return the
@@ -238,14 +245,14 @@ static int edma_get_settings(struct net_device *netdev,
 		if (!(adapter->poll_required)) {
 			if (adapter->forced_speed != SPEED_UNKNOWN) {
 				/* set speed and duplex */
-				ethtool_cmd_speed_set(ecmd, SPEED_1000);
-				ecmd->duplex = DUPLEX_FULL;
+				cmd->base.speed = SPEED_1000;
+				cmd->base.duplex = DUPLEX_FULL;
 
 				/* Populate capabilities advertised by self */
-				ecmd->advertising = 0;
-				ecmd->autoneg = 0;
-				ecmd->port = PORT_TP;
-				ecmd->transceiver = XCVR_EXTERNAL;
+				linkmode_zero(cmd->link_modes.advertising);
+				cmd->base.autoneg = 0;
+				cmd->base.port = PORT_TP;
+				cmd->base.transceiver = XCVR_EXTERNAL;
 			} else {
 				/* non link polled and non
 				 * forced speed/duplex interface
@@ -262,7 +269,7 @@ static int edma_get_settings(struct net_device *netdev,
  *	Set EDMA settings
  */
 static int edma_set_settings(struct net_device *netdev,
-			     struct ethtool_cmd *ecmd)
+			    const struct ethtool_link_ksettings *cmd)
 {
 	struct edma_adapter *adapter = netdev_priv(netdev);
 	struct phy_device *phydev = NULL;
@@ -272,16 +279,16 @@ static int edma_set_settings(struct net_device *netdev,
 		return -EPERM;
 
 	phydev = adapter->phydev;
-	phydev->advertising = ecmd->advertising;
-	phydev->autoneg = ecmd->autoneg;
-	phydev->speed = ethtool_cmd_speed(ecmd);
-	phydev->duplex = ecmd->duplex;
+	linkmode_copy(phydev->advertising, cmd->link_modes.advertising);
+	linkmode_copy(phydev->supported, cmd->link_modes.supported);
+	phydev->autoneg = cmd->base.autoneg;
+	phydev->speed = cmd->base.speed;
+	phydev->duplex = cmd->base.duplex;
 
 	genphy_config_aneg(phydev);
 
 	return 0;
 }
-#endif
 
 /* edma_get_coalesce
  *	get interrupt mitigation
@@ -356,8 +363,8 @@ static const struct ethtool_ops edma_ethtool_ops = {
 	.get_msglevel = &edma_get_msglevel,
 	.nway_reset = &edma_nway_reset,
 	.get_wol = &edma_get_wol,
-//	.get_settings = &edma_get_settings,
-//	.set_settings = &edma_set_settings,
+	.get_link_ksettings = &edma_get_settings,
+	.set_link_ksettings = &edma_set_settings,
 	.get_strings = &edma_get_strings,
 	.get_sset_count = &edma_get_strset_count,
 	.get_ethtool_stats = &edma_get_ethtool_stats,
-- 
2.24.1


_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list