[OpenWrt-Devel] [PATCH] ath79: switch to kernel 5.4

Hauke Mehrtens hauke at hauke-m.de
Wed Jul 1 18:49:17 EDT 2020

On 7/1/20 6:50 PM, Henrique de Moraes Holschuh wrote:
> On 12/05/2020 18:46, Hauke Mehrtens wrote:
>> On 5/12/20 12:24 PM, Bjørn Mork wrote:
>>> Hauke Mehrtens <hauke at hauke-m.de> writes:
>>>> I also get this problem with mainline kernel.
>>>> See here for some more details:
>>>> https://bugs.openwrt.org/index.php?do=details&task_id=2928
>>>> https://gcc.gnu.org/bugzilla/show_bug.cgi?id=94506
>>> Hello,
>>> I wondered what the current state of this is?  Reading that GCC bug it
>>> looks like all the results we've seen are just arbitrary, and either
>>> triggering a latent bug or not.
>>> How do we proceed from there?
>>> FWIW, I just built current master (146e18af568a) with 5.4 kernel using
>>> GCC 9.3.  And like others have reported, this booted just fine without
>>> any other tricks.
>>> But it seems a bit too fragile for any release if it could break any
>>> time we do a GCC or kernel update...
>> Hi,
>> I would prefer if we know the root cause, more code could be compiled
>> wrong and just silently fail.
> Here's a data point.   We *do* have a bug in the toolchain that causes
> it to generate broken binaries (maybe only the kernel?) in certain
> situations, and it is *not* new.
> Since 18.06 (maybe earlier), I can 100% reproduce a broken image here
> that will crash-loop on boot on ar71xx *or* ath79 if I do the following
> steps:
> 0. Arch is ar71xx (18.06) or ath79 (19.07).   Target device tplink
> Archer C7v4 (MIPS 74kc).
> 1. Clean the toolchain and build tree so that it is going to be rebuilt
> from scratch
> 2. enable TARGET_OPTIONS using menuconfig
> 3. change CONFIG_TARGET_OPTIMIZATION, replace -mtune=24kc with -mtune=74kc
> build.  The resulting image will crash-loop if installed.  Note: I did
> not try with the default options though.  I enable LuCi and a few other
> packages as built-in, etc.  If anyone fails to reproduce, I can send my
> standard .config.
> DISABLE TARGET_OPTIONS (so that defaults are used), clean everything (so
> that the toolchain and all binaries will be rebuilt). rebuild, so that
> the toolchain is built without TARGET_OPTIONS.
> it works.
> Enable (2) and (3) again, do a new build, this time *not* rebuilding the
> toolchain.  i.e. only the kernel and packages are rebuilt with
> TARGET_OPTIONS enabled, and -mtune=74kc.
> it works.
> So, the problem seems to be on the toolchain build itself, that creates
> a faulty toolchain when TARGET_OPTIONS is active (I don't recall if it
> causes trouble if you just enable TARGET_OPTIONS but don't touch

I think some MIPS hazard handling in the kernel is wrong. This would
also explain why we see this only on the MIPS 74K CPU which is an out of
order CPU and not on the MIPS 24K CPUs.

When I add a call to ehb(); at the end of the configure_status()
function the kernel does not crash any more.
This adds the ehb instruction, but it also generates a little bit
different instructions for the configure_exception_vector() function.

If the ST0_MX bit goes into effect only some instructions later, this
should not be a problem as it takes pretty long till we call the first
DSP instruction.

I think the problem is somewhere in the configure_exception_vector()


-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.openwrt.org/pipermail/openwrt-devel/attachments/20200702/0c272116/attachment.sig>

More information about the openwrt-devel mailing list