[OpenWrt-Devel] [PATCH v4] ramips: add support for Planex MZK-DP150N

YuheiOKAWA tochiro.srchack at gmail.com
Wed Jul 15 11:22:33 EDT 2015


This patch add support for Planex MZK-DP150N.
a mini router on the MT7620A SoC with one Ethernet port and a 802.11n 2.4 GHz radio.

Signed-off-by: YuheiOKAWA <tochiro.srchack at gmail.com>
---
 target/linux/ramips/base-files/etc/board.d/01_leds |  3 +
 .../linux/ramips/base-files/etc/board.d/02_network |  7 ++
 target/linux/ramips/base-files/etc/diag.sh         |  3 +
 target/linux/ramips/base-files/lib/ramips.sh       |  3 +
 .../ramips/base-files/lib/upgrade/platform.sh      |  1 +
 target/linux/ramips/dts/MZK-DP150N.dts             | 98 ++++++++++++++++++++++
 target/linux/ramips/image/Makefile                 |  3 +
 target/linux/ramips/rt305x/profiles/planex.mk      | 17 ++++
 8 files changed, 135 insertions(+)
 create mode 100644 target/linux/ramips/dts/MZK-DP150N.dts
 create mode 100644 target/linux/ramips/rt305x/profiles/planex.mk

diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index fe3a79d..0672a22 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -265,6 +265,9 @@ case $board in
 	zte-q7)
 		set_wifi_led "zte:blue:status"
 		;;
+	mzk-dp150n)
+		ucidef_set_led_default "power" "power" "mzkdp150n:green:power" "1"
+		;;
 esac
 
 board_config_flush
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index 9fb3535..f896afa 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -261,6 +261,13 @@ ramips_setup_interfaces()
 		ucidef_add_switch_vlan "switch0" "1" "1 2 3 4 5t"
 		ucidef_add_switch_vlan "switch0" "2" "0 5t"
 		;;
+
+	mzk-dp150n)
+		ucidef_set_interface_lan "eth0.1"
+		ucidef_add_switch "switch0" "1" "1"
+		ucidef_add_switch_vlan "switch0" "1" "0 4 6t"
+		;;
+
 	*)
 		RT3X5X=`cat /proc/cpuinfo | egrep "(RT3.5|RT5350)"`
 		if [ -n "${RT3X5X}" ]; then
diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index 46e519a..319763e 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -249,6 +249,9 @@ get_status_led() {
 	zte-q7)
 		status_led="zte:red:status"
 		;;
+	mzk-dp150n)
+		status_led="mzkdp150n:green:power"
+		;;
 	esac
 }
 
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index 3d40ab9..d7fd5f9 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -421,6 +421,9 @@ ramips_board_detect() {
 	*"Mediatek MT7628AN evaluation board")
 		name="mt7628"
 		;;
+	*"Planex MZK-DP150N")
+		name="mzk-dp150n"
+		;;
 	*)
 		name="generic"
 		;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index 8f45a84..04af322 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -71,6 +71,7 @@ platform_check_image() {
 	mpr-a2 | \
 	mr-102n | \
 	mzk-w300nh2 | \
+	mzk-dp150n | \
 	nbg-419n | \
 	nw718 | \
 	omni-emb | \
diff --git a/target/linux/ramips/dts/MZK-DP150N.dts b/target/linux/ramips/dts/MZK-DP150N.dts
new file mode 100644
index 0000000..ae986f7
--- /dev/null
+++ b/target/linux/ramips/dts/MZK-DP150N.dts
@@ -0,0 +1,98 @@
+/dts-v1/;
+
+/include/ "rt5350.dtsi"
+
+/ {
+	compatible = "MZK-DP150N", "ralink,rt5350-soc";
+	model = "Planex MZK-DP150N";
+
+	palmbus at 10000000 {
+		gpio1: gpio at 660 {
+			status = "okay";
+		};
+
+		spi at b00 {
+			status = "okay";
+
+			m25p80 at 0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "s25fl064k";
+				reg = <0>;
+				linux,modalias = "m25p80", "s25fl064k";
+				spi-max-frequency = <10000000>;
+
+				partition at 0 {
+					label = "uboot";
+					reg = <0x0 0x30000>;
+					read-only;
+				};
+
+				partition at 30000 {
+					label = "uboot-env";
+					reg = <0x30000 0x10000>;
+					read-only;
+				};
+
+				factory: partition at 40000 {
+					label = "factory";
+					reg = <0x40000 0x10000>;
+					read-only;
+				};
+
+				partition at 50000 {
+					label = "firmware";
+					reg = <0x50000 0x3b0000>;
+				};
+			};
+
+			spidev at 1 {
+				compatible = "linux,spidev";
+				spi-max-frequency = <10000000>;
+				reg = <1>;
+			};
+		};
+	};
+
+	pinctrl {
+		state_default: pinctrl0 {
+			gpio {
+				ralink,group = "jtag", "uartf", "led";
+				ralink,function = "gpio";
+			};
+		};
+	};
+
+	ethernet at 10100000 {
+		mtd-mac-address = <&factory 0x4>;
+	};
+
+	esw at 10110000 {
+		ralink,portmap = <0x17>;
+	};
+
+	wmac at 10180000 {
+		ralink,mtd-eeprom = <&factory 0>;
+		ralink,led-polarity = <1>;
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		power {
+			label = "mzkdp150n:green:power";
+			gpios = <&gpio0 9 1>;
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <20>;
+		reset {
+			label = "reset";
+			gpios = <&gpio0 10 1>;
+			linux,code = <0x198>;
+		};
+	};
+};
diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile
index 2fe5fdd..b71d935 100644
--- a/target/linux/ramips/image/Makefile
+++ b/target/linux/ramips/image/Makefile
@@ -609,6 +609,8 @@ Image/Build/Profile/W502U=$(call BuildFirmware/Default8M/$(1),$(1),w502u,W502U)
 Image/Build/Profile/WCR150GN=$(call BuildFirmware/Default4M/$(1),$(1),wcr150gn,WCR150GN)
 
 
+Image/Build/Profile/MZK-DP150N=$(call BuildFirmware/Default4M/$(1),$(1),mzk-dp150n,MZK-DP150N)
+
 buffalo_whrg300n_mtd_size=3801088
 define BuildFirmware/WHRG300N/squashfs
 	$(call BuildFirmware/Default4M/$(1),$(1),whr-g300n,WHR-G300N)
@@ -772,6 +774,7 @@ define Image/Build/Profile/Default
 	$(call Image/Build/Profile/X5,$(1))
 	$(call Image/Build/Profile/X8,$(1))
 	$(call Image/Build/Profile/XDXRN502J,$(1))
+	$(call Image/Build/Profile/MZK-DP150N,$(1))
 
 endef
 endif
diff --git a/target/linux/ramips/rt305x/profiles/planex.mk b/target/linux/ramips/rt305x/profiles/planex.mk
new file mode 100644
index 0000000..d0d9ac9
--- /dev/null
+++ b/target/linux/ramips/rt305x/profiles/planex.mk
@@ -0,0 +1,17 @@
+#
+# Copyright (C) 2014 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/MZK-DP150N
+	NAME:=Planex MZK-DP150N
+	PACKAGES:= kmod-spi-dev
+endef
+
+define Profile/MZK-DP150N/Description
+	Package set optimized for the Planex MZK-DP150N.
+endef
+
+$(eval $(call Profile,MZK-DP150N))
-- 
1.9.1
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list