[OpenWrt-Devel] [PATCH v2] comgt: Allow using non-TTY devices

Matti Laakso malaakso at elisanet.fi
Mon Jan 19 15:25:28 EST 2015


Some Huawei mobile broadband sticks utilizing the NCM protocol expose
the control channel as a cdc-wdm device node instead of a virtual TTY.
This device node does not support the terminal ioctls. This patch
adds a check whether the provided device is a TTY or not and does not
attempt to use the terminal ioctls if they are not supported.

v2: reduce diffstat by simplifying code a little
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
---
 .../utils/comgt/patches/004-check_tty.patch        | 68 ++++++++++++++++++++++
 1 file changed, 68 insertions(+)
 create mode 100644 package/network/utils/comgt/patches/004-check_tty.patch

diff --git a/package/network/utils/comgt/patches/004-check_tty.patch b/package/network/utils/comgt/patches/004-check_tty.patch
new file mode 100644
index 0000000..b81b051
--- /dev/null
+++ b/package/network/utils/comgt/patches/004-check_tty.patch
@@ -0,0 +1,68 @@
+--- a/comgt.c
++++ b/comgt.c
+@@ -91,6 +91,7 @@ unsigned long hstart,hset;
+ char NullString[]={ "" };
+ BOOL lastcharnl=1; /* Indicate that last char printed from getonebyte
+                                was a nl, so no new one is needed */
++BOOL tty=1;
+ 
+ 
+ //"open com \"/dev/modem\"\nset com 38400n81\nset senddelay 0.05\nsend \"ATi^m\"\nget 2 \" ^m\" $s\nprint \"Response : \",$s,\"\\n\"\nget 2 \" ^m\" $s\nprint \"Response :\",$s,\"\\n\"\nget 2 \" ^m\" $s\nprint \"Response : \",$s,\"\\n\"\n\n";
+@@ -920,7 +921,7 @@ BOOL getonoroff(void) {
+ void setcom(void) {
+   stbuf.c_cflag &= ~(CBAUD | CSIZE | CSTOPB | CLOCAL | PARENB);
+   stbuf.c_cflag |= (speed | bits | CREAD | clocal | parity | stopbits );
+-  if (ioctl(comfd, TCSETA, &stbuf) < 0) {
++  if (tty && ioctl(comfd, TCSETA, &stbuf) < 0) {
+     serror("Can't ioctl set device",1);
+   }
+ }
+@@ -1224,7 +1225,7 @@ void doclose(void) {
+   if(strcmp(token,"hardcom")==0) {
+     if(comfd== -1) serror("Com device not open",1);
+     vmsg("Closing device");
+-    if (ioctl(comfd, TCSETA, &svbuf) < 0) {
++    if (tty && ioctl(comfd, TCSETA, &svbuf) < 0) {
+       sprintf(msg,"Can't ioctl set device %s.\n",device);
+       serror(msg,1);
+     }
+@@ -1266,12 +1267,17 @@ void opengt(void) {
+       ext(1);
+     }
+   }
+-  if (ioctl (comfd, TCGETA, &svbuf) < 0) {
++  if (isatty (comfd))
++    tty=1;
++  else
++    tty=0;
++  if (tty && ioctl (comfd, TCGETA, &svbuf) < 0) {
+     sprintf(msg,"Can't control %s, please try again.\n",device);
+     serror(msg,1);
+   }
+   setenv("COMGTDEVICE",device,1);
+-  ioctl(comfd, TCGETA, &stbuf);
++  if (tty)
++    ioctl(comfd, TCGETA, &stbuf);
+   speed=stbuf.c_cflag & CBAUD;
+   if (high_speed == 0)  strcpy(cspeed,"115200");
+   else strcpy(cspeed,"57600");
+@@ -1302,12 +1308,16 @@ void opendevice(void) {
+     }
+   }
+   else comfd=0;
+-
+-  if (ioctl (comfd, TCGETA, &svbuf) < 0) {
++  if (isatty (comfd))
++    tty=1;
++  else
++    tty=0;
++  if (tty && ioctl (comfd, TCGETA, &svbuf) < 0) {
+     sprintf(msg,"Can't ioctl get device %s.\n",device);
+     serror(msg,1);
+   }
+-  ioctl(comfd, TCGETA, &stbuf);
++  if (tty)
++    ioctl(comfd, TCGETA, &stbuf);
+   speed=stbuf.c_cflag & CBAUD;
+   switch(speed) {
+     case B0: strcpy(cspeed,"0");break;
-- 
2.1.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list