[OpenWrt-Devel] [PATCH] ramips: add support for Intenso Memory 2 Move USB 3.0

Christian Lamparter chunkeey at googlemail.com
Thu Jan 15 16:47:19 EST 2015


This adds support for a rt5350-based "portable nas" solution
from Intenso. The board comes with 32M RAM and 8M Flash, the
built-in HDD is connected/accessible via a usb3.0<->sata
bridge VLI VL701.

The device has 1 Ethernet port (100M/10M), 1 micro b usb 3.0
socket (for charging the battery, or accessing the hdd directly).
Wireless connectivity is provided by the rt5350 SoC [i.e.:
802.11n 1x1 2.4 GHz with a pcb antenna.]

Serial, leds, wifi, ethernet and usb are tested and
as far as I can tell: they are working fine (tm).

Signed-off-by: Christian Lamparter <chunkeey at googlemail.com>
---
Any comments/suggestions or wishes? Most of the work is
based/taken from other devices. So apart from some non-obvious
stuff, it should all be fine too. 

What is a bit unique: the way of flashing the device. This
will require a tftp server [hardcoded to 192.168.1.201]
and a few cables to the uart. I'll write a "how to flash 
openwrt on a m2m" once this patch [or a better version] is
accepted.

Regards,
Christian
---
 target/linux/ramips/base-files/etc/board.d/01_leds |   4 +
 .../linux/ramips/base-files/etc/board.d/02_network |   5 +
 target/linux/ramips/base-files/etc/diag.sh         |   3 +
 target/linux/ramips/base-files/lib/ramips.sh       |   3 +
 .../ramips/base-files/lib/upgrade/platform.sh      |   1 +
 target/linux/ramips/dts/M2M.dts                    | 113 +++++++++++++++++++++
 target/linux/ramips/image/Makefile                 |   3 +
 target/linux/ramips/rt305x/profiles/m2m.mk         |  21 ++++
 8 files changed, 153 insertions(+)
 create mode 100644 target/linux/ramips/dts/M2M.dts
 create mode 100644 target/linux/ramips/rt305x/profiles/m2m.mk

diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index 405a6c0..7b29ac0 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -148,6 +148,10 @@ case $board in
 	nw718)
 		set_usb_led "nw718:amber:usb"
 		;;
+	m2m)
+		set_wifi_led "m2m:blue:wifi"
+		ucidef_set_led_netdev "eth" "Ethernet" "m2m:green:wan" "eth0"
+		;;
 	omni-emb-hpm)
 		ucidef_set_led_default "power" "POWER" "emb:orange:power" "1"
 		ucidef_set_led_netdev "eth" "ETH" "emb:green:eth" "eth0"
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index a86466e..e425510 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -62,6 +62,11 @@ ramips_setup_interfaces()
 		ucidef_set_interface_lan "eth0.2"
 		;;
 
+	m2m)
+		ucidef_add_switch "switch0" "4"
+		ucidef_set_interface_lan "eth0"
+		;;
+
 	wizard8800 | \
 	wl-330n | \
 	wmr300)
diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index 103dfcd..c43cb54 100755
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -79,6 +79,9 @@ get_status_led() {
 	hw550-3g)
 		status_led="hw550-3g:green:status"
 		;;
+	m2m)
+		status_led="m2m:blue:wifi"
+		;;
 	m3)
 		status_led="m3:blue:status"
 		;;
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index 540da33..f783065 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -211,6 +211,9 @@ ramips_board_detect() {
 	*"NW718")
 		name="nw718"
 		;;
+	*"Intenso Memory 2 Move")
+		name="m2m"
+		;;
 	*"Omnima EMB HPM")
 		name="omni-emb-hpm"
 		;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index 95cad63..2d48192 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -55,6 +55,7 @@ platform_check_image() {
 	ht-tm02 | \
 	hw550-3g | \
 	ip2202 | \
+	m2m | \
 	m3 | \
 	m4 | \
 	mlw221 | \
diff --git a/target/linux/ramips/dts/M2M.dts b/target/linux/ramips/dts/M2M.dts
new file mode 100644
index 0000000..aa98991
--- /dev/null
+++ b/target/linux/ramips/dts/M2M.dts
@@ -0,0 +1,113 @@
+/dts-v1/;
+
+/include/ "rt5350.dtsi"
+
+/ {
+	compatible = "M2M", "ralink,rt5350-soc";
+	model = "Intenso Memory 2 Move";
+
+	chosen {
+		bootargs = "console=ttyS1,57600n8 root=/dev/mtdblock5";
+	};
+
+	palmbus at 10000000 {
+		uart at 500 {
+			status = "okay";
+		};
+
+		spi at b00 {
+			status = "okay";
+			m25p80 at 0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "mx25l6405d";
+				reg = <0 0>;
+				linux,modalias = "m25p80", "mx25l6405d";
+				spi-max-frequency = <10000000>;
+
+				partition at 0 {
+					label = "Bootloader";
+					reg = <0x0 0x30000>;
+					read-only;
+				};
+
+				partition at 30000 {
+					label = "Config";
+					reg = <0x30000 0x10000>;
+					read-only;
+				};
+
+				factory: partition at 40000 {
+					label = "Factory";
+					reg = <0x40000 0x10000>;
+					read-only;
+				};
+
+				partition at 50000 {
+					label = "firmware";
+					reg = <0x50000 0x7b0000>;
+				};
+			};
+		};
+	};
+
+	pinctrl {
+		state_default: pinctrl0 {
+			gpio {
+				ralink,group = "i2c", "jtag", "uartf";
+				ralink,function = "gpio";
+			};
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		wifi {
+			label = "m2m:blue:wifi";
+			gpios = <&gpio0 7 1>;
+		};
+		wan {
+			label = "m2m:green:wan";
+			gpios = <&gpio0 12 1>;
+		};
+	};
+
+	gpio-keys-polled {
+		gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <20>;
+			power {
+				label = "power";
+				gpios = <&gpio0 1 1>;
+				linux,code = <0x116>;
+			};
+			reset {
+				label = "reset";
+				gpios = <&gpio0 10 1>;
+				linux,code = <0x198>;
+			};
+		};
+	};
+
+	ethernet at 10100000 {
+		mtd-mac-address = <&factory 0x28>;
+	};
+
+	esw at 10110000 {
+		ralink,portmap = <0x2f>;
+	};
+
+	ehci at 101c0000 {
+		status = "okay";
+	};
+
+	ohci at 101c1000 {
+		status = "okay";
+	};
+
+	wmac at 10180000 {
+		ralink,mtd-eeprom = <&factory 0x0>;
+	};
+};
diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile
index 82cadd7..e385966 100644
--- a/target/linux/ramips/image/Makefile
+++ b/target/linux/ramips/image/Makefile
@@ -546,6 +546,8 @@ Image/Build/Profile/NCS601W=$(call BuildFirmware/Default8M/$(1),$(1),ncs601W,NCS
 nw718_mtd_size=3801088
 Image/Build/Profile/NW718=$(call BuildFirmware/CustomFlashFactory/$(1),$(1),nw718m,NW718,$(nw718_mtd_size),ARA1B4NCRNW718;1,factory)
 
+Image/Build/Profile/M2M=$(call BuildFirmware/Default8M/$(1),$(1),m2m,M2M,Linux Kernel Image)
+
 Image/Build/Profile/OMNI-EMB=$(call BuildFirmware/Default8M/$(1),$(1),omni-emb,OMNI-EMB)
 
 Image/Build/Profile/OMNI-PLUG=$(call BuildFirmware/Default8M/$(1),$(1),omni-plug,OMNI-PLUG)
@@ -694,6 +696,7 @@ define Image/Build/Profile/Default
 	$(call Image/Build/Profile/HT-TM02,$(1))
 	$(call Image/Build/Profile/HW550-3G,$(1))
 	$(call Image/Build/Profile/IP2202,$(1))
+	$(call Image/Build/Profile/M2M,$(1))
 	$(call Image/Build/Profile/M3,$(1))
 	$(call Image/Build/Profile/M4,$(1))
 	$(call Image/Build/Profile/MOFI3500-3GN,$(1))
diff --git a/target/linux/ramips/rt305x/profiles/m2m.mk b/target/linux/ramips/rt305x/profiles/m2m.mk
new file mode 100644
index 0000000..e5cb6b8
--- /dev/null
+++ b/target/linux/ramips/rt305x/profiles/m2m.mk
@@ -0,0 +1,20 @@
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/M2M
+	NAME:=Intenso Memory 2 Move
+	PACKAGES:=\
+		kmod-ledtrig-netdev kmod-ledtrig-timer kmod-leds-gpio \
+		kmod-usb-core kmod-usb2 kmod-usb-storage kmod-scsi-core \
+		kmod-fs-ext4 kmod-fs-vfat block-mount
+endef
+
+define Profile/M2M/Description
+	Package set for Intenso Memory 2 Move USB 3.0
+endef
+
+$(eval $(call Profile,M2M))
-- 
2.1.4
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list