[OpenWrt-Devel] lantiq v3.18
Roger Pueyo Centelles
rogerpueyo at rogerpueyo.com
Sun Feb 22 14:40:26 EST 2015
Sure.
U-Boot 2013.10-openwrt5-00014-g0b78b5c-dirty (Mar 11 2014 - 22:56:27) arv7519rw
Board: Lantiq ARV7519RW VRX200 Family Board
SoC: Lantiq VRX288 v1.1
CPU: 500 MHz
IO: 250 MHz
BUS: 250 MHz
BOOT: NOR
DRAM: 128 MiB
Flash: 32 MiB
In: serial
Out: serial
Err: serial
Net: ltq-eth
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at b0080000 ...
Image Name: MIPS OpenWrt Linux-3.18.7
Created: 2015-02-22 11:56:23 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1546993 Bytes = 1.5 MiB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.18.7 (lordroger at xeon) (gcc version
4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r44507) ) #1 Sun Feb 22 12:56:14
CET 2015
[ 0.000000] SoC: VR9 rev 1.1
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019555 (MIPS 34Kc)
[ 0.000000] MIPS: machine is ARV7519RW22 - Astoria Networks ARV7519RW22-A-LT
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases,
linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 32512
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00044751
[ 0.000000] Readback ErrCtl register=00044751
[ 0.000000] Memory: 125044K/131072K available (3312K kernel code,
147K rwdata, 932K rodata, 196K init, 205K bss, 6028K reserved)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 500MHz
[ 0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[ 0.032000] pid_max: default: 32768 minimum: 301
[ 0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.044000] pinctrl core: initialized pinctrl subsystem
[ 0.048000] NET: Registered protocol family 16
[ 0.056000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7,
channels: 28
[ 0.064000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[ 0.088000] usbcore: registered new interface driver usbfs
[ 0.092000] usbcore: registered new interface driver hub
[ 0.096000] usbcore: registered new device driver usb
[ 0.100000] Switched to clocksource MIPS
[ 0.104000] NET: Registered protocol family 2
[ 0.108000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.116000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.124000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.128000] TCP: reno registered
[ 0.132000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.136000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.144000] NET: Registered protocol family 1
[ 0.148000] gptu: totally 6 16-bit timers/counters
[ 0.152000] gptu: misc_register on minor 63
[ 0.156000] gptu: succeeded to request irq 126
[ 0.164000] gptu: succeeded to request irq 127
[ 0.168000] gptu: succeeded to request irq 128
[ 0.172000] gptu: succeeded to request irq 129
[ 0.176000] gptu: succeeded to request irq 130
[ 0.180000] gptu: succeeded to request irq 131
[ 0.184000] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy22f_a1x.bin
[ 0.192000] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 7900000
[ 0.200000] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 7900000
[ 0.308000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.316000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.320000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.332000] msgmni has been set to 244
[ 0.336000] io scheduler noop registered
[ 0.340000] io scheduler deadline registered (default)
[ 0.344000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112,
base_baud = 0) is a lantiq,asc
[ 0.352000] console [ttyLTQ0] enabled
[ 0.352000] console [ttyLTQ0] enabled
[ 0.360000] bootconsole [early0] disabled
[ 0.360000] bootconsole [early0] disabled
[ 0.368000] lantiq nor flash device: 02000000 at 10000000
[ 0.372000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank.
Manufacturer ID 0x0000c2 Chip ID 0x00227e
[ 0.384000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.388000] Amd/Fujitsu Extended Query version 1.3.
[ 0.392000] number of CFI chips: 1
[ 0.396000] lantiq nor flash device: 02000000 at 16000000
[ 0.404000] ltq-nor 10000000.nor-boot: probing failed
[ 0.512000] libphy: lantiq,xrx200-mdio: probed
[ 0.532000] net-xrx200: invalid MAC, using random
[ 0.600000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3]
(phy_addr=0:00, irq=-1)
[ 0.668000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4]
(phy_addr=0:13, irq=-1)
[ 0.736000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4]
(phy_addr=0:14, irq=-1)
[ 0.804000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4]
(phy_addr=0:11, irq=-1)
[ 0.872000] eth0: attached PHY [Lantiq XWAY XRX PHY22F v1.4]
(phy_addr=0:12, irq=-1)
[ 0.880000] wdt 1f8803f0.watchdog: Init done
[ 0.884000] TCP: cubic registered
[ 0.884000] NET: Registered protocol family 17
[ 0.888000] bridge: automatic filtering via arp/ip/ip6tables has
been deprecated. Update your scripts to load br_netfilter if you need
this.
[ 0.904000] 8021q: 802.1Q VLAN Support v1.8
[ 0.908000] UBIFS error (pid 1): ubifs_mount: cannot open
"ubi0:rootfs", error -19
[ 0.916000] VFS: Cannot open root device "(null)" or
unknown-block(0,0): error -6
[ 0.924000] Please append a correct "root=" boot option; here are
the available partitions:
[ 0.932000] Kernel panic - not syncing: VFS: Unable to mount root
fs on unknown-block(0,0)
[ 0.932000] ---[ end Kernel panic - not syncing: VFS: Unable to
mount root fs on unknown-block(0,0)
[ 33.092000] random: nonblocking pool is initialized
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list