[OpenWrt-Devel] ar71xx update to v3.18

Sun Feb 15 19:17:42 EST 2015

It builds oke now,

but its doesn't boot on my device. i don't get to see any (informative)
boot error's (see log).

John Crispin schreef op 15-2-2015 om 22:16:
> 
> 
> On 15/02/2015 21:44, Michaël Zweers wrote:
>>
>> Hello,
>>
>> I got a error message (kernel compile log included) when building v3.18
>> for wr703n.
>>
>> If you need additional info let me know.
>>
>>
> 
> please retry, i just pushed a fix
> 
-------------- next part --------------

*********************************************
*        U-Boot 1.1.4MGZ MOD_V1  (Jun 24 2014)        *
*********************************************

AP121 (AR9331) U-Boot for TL-WR703N

DRAM:   32 MB DDR 16-bit
FLASH:  Winbond W25Q128 (16 MB)
CLOCKS: 400/400/200/33 MHz (CPU/RAM/AHB/SPI)

LED on during eth initialization...

## Error: MDIO_BUSY!
Hit any key to stop autobooting:  0

Booting image at: 0x9F020000

   Image name:   OpenWrt r44459
   Image type:   MIPS Linux Kernel Image (lzma compressed)
   Data size:    1205904 Bytes = 1.2 MB
   Load address: 0x80060000
   Entry point:  0x80060000

Uncompressing kernel image... OK!
Starting kernel...

[    0.000000] Linux version 3.18.7 (user at HartOfGold) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r44457) ) #1 Mon Feb 16 00:49:34 CET 2015
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 28324K/32768K available (2627K kernel code, 131K rwdata, 544K rodata, 208K init, 193K bss, 4444K reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.100000] NET: Registered protocol family 16
[    0.100000] MIPS: machine is TP-LINK TL-WR703N v1
[    0.380000] Switched to clocksource MIPS
[    0.380000] NET: Registered protocol family 2
[    0.390000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.390000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.390000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.400000] TCP: reno registered
[    0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.420000] NET: Registered protocol family 1
[    0.420000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.440000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.450000] msgmni has been set to 55
[    0.450000] io scheduler noop registered
[    0.460000] io scheduler deadline registered (default)
[    0.460000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.470000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a AR933X UART
[    0.480000] console [ttyATH0] enabled
[    0.480000] console [ttyATH0] enabled
[    0.490000] bootconsole [early0] disabled
[    0.490000] bootconsole [early0] disabled
[    0.500000] m25p80 spi0.0: found w25q128, expected m25p80
[    0.500000] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.510000] 5 tp-link partitions found on MTD device spi0.0
[    0.510000] Creating 5 MTD partitions on "spi0.0":
[    0.520000] 0x000000000000-0x000000020000 : "u-boot"
[    0.520000] 0x000000020000-0x000000146890 : "kernel"
[    0.530000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.540000] 0x000000146890-0x000000ff0000 : "rootfs"
[    0.540000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.560000] mtd: device 2 (rootfs) set to be root filesystem
[    0.560000] 1 squashfs-split partitions found on MTD device rootfs
[    0.570000] 0x000000400000-0x000000ff0000 : "rootfs_data"
[    0.580000] 0x000000ff0000-0x000001000000 : "art"
[    0.580000] 0x000000020000-0x000000ff0000 : "firmware"
[    0.620000] libphy: ag71xx_mdio: probed
[    1.220000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    1.230000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    1.230000] TCP: cubic registered
[    1.230000] NET: Registered protocol family 17
[    1.240000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.250000] Bridge firewalling registered
[    1.250000] 8021q: 802.1Q VLAN Support v1.8
[    1.270000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.280000] Freeing unused kernel memory: 208K (8039c000 - 803d0000)
procd: Console is alive
procd: - watchdog -
[    3.690000] usbcore: registered new interface driver usbfs
[    3.700000] usbcore: registered new interface driver hub
[    3.700000] usbcore: registered new device driver usb
[    3.710000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.720000] ehci-platform: EHCI generic platform driver
[    3.720000] ehci-platform ehci-platform: EHCI Host Controller
[    3.730000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    3.740000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    3.760000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    3.760000] hub 1-0:1.0: USB hub found
[    3.760000] hub 1-0:1.0: 1 port detected
[    3.770000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.780000] ohci-platform: OHCI generic platform driver
procd: - preinit -
procd: Failed to start preinit
procd: - early -
procd: - watchdog -
procd: - ubus -
[    6.120000] random: ubusd urandom read with 10 bits of entropy available
procd: - init -
Please press Enter to activate this console.
procd: - init complete -
[   81.930000] random: nonblocking pool is initialized

Failed to execute Please press Enter to activate this console.

Failed to execute

Please press Enter
Please press EnterPlease press Enter to activate this console.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/openwrt-devel/attachments/20150216/86405c19/attachment.sig>
-------------- next part --------------
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel