[OpenWrt-Devel] [PATCH 02/10] imx6: Add 4.3 support

Pushpal Sidhu psidhu at gateworks.com
Mon Dec 21 17:25:12 EST 2015


Build and boot tested on the following hardware:
 * GW54xx
 * GW53xx
 * GW52xx
 * GW51xx
 * GW552x
 * GW551x

Signed-off-by: Pushpal Sidhu <psidhu at gateworks.com>
---
 target/linux/imx6/config-4.3                       |  410 ++++++++
 .../linux/imx6/files-4.3/drivers/net/phy/gw16083.c | 1046 ++++++++++++++++++++
 .../linux/imx6/files-4.3/drivers/net/phy/gw16083.h |  123 +++
 ...-ventana-set-GW54xx-PMIC-swbst-regulator-.patch |   28 +
 ...mx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch |   37 +
 ...mx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch |   76 ++
 target/linux/imx6/patches-4.3/100-bootargs.patch   |   13 +
 ...-add-i210-i211-support-for-phy-read-write.patch |  131 +++
 ...-phy-read-write-functions-that-accept-phy.patch |  266 +++++
 ...egister-mii_bus-for-SerDes-w-external-phy.patch |  314 ++++++
 ...ver-for-GW16083-Ethernet-Expansion-Mezzan.patch |   31 +
 ...-imx-ventana-added-GW16083-to-device-tree.patch |   64 ++
 12 files changed, 2539 insertions(+)
 create mode 100644 target/linux/imx6/config-4.3
 create mode 100644 target/linux/imx6/files-4.3/drivers/net/phy/gw16083.c
 create mode 100644 target/linux/imx6/files-4.3/drivers/net/phy/gw16083.h
 create mode 100644 target/linux/imx6/patches-4.3/035-ARM-dts-imx-ventana-set-GW54xx-PMIC-swbst-regulator-.patch
 create mode 100644 target/linux/imx6/patches-4.3/036-ARM-dts-imx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch
 create mode 100644 target/linux/imx6/patches-4.3/037-ARM-dts-imx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch
 create mode 100644 target/linux/imx6/patches-4.3/100-bootargs.patch
 create mode 100644 target/linux/imx6/patches-4.3/202-net-igb-add-i210-i211-support-for-phy-read-write.patch
 create mode 100644 target/linux/imx6/patches-4.3/203-net-igb-add-phy-read-write-functions-that-accept-phy.patch
 create mode 100644 target/linux/imx6/patches-4.3/204-net-igb-register-mii_bus-for-SerDes-w-external-phy.patch
 create mode 100644 target/linux/imx6/patches-4.3/205-phy-add-driver-for-GW16083-Ethernet-Expansion-Mezzan.patch
 create mode 100644 target/linux/imx6/patches-4.3/206-ARM-imx-ventana-added-GW16083-to-device-tree.patch

diff --git a/target/linux/imx6/config-4.3 b/target/linux/imx6/config-4.3
new file mode 100644
index 0000000..ae4f797
--- /dev/null
+++ b/target/linux/imx6/config-4.3
@@ -0,0 +1,410 @@
+CONFIG_AHCI_IMX=y
+CONFIG_ALIGNMENT_TRAP=y
+CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
+CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
+CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
+CONFIG_ARCH_HAS_RESET_CONTROLLER=y
+CONFIG_ARCH_HAS_SG_CHAIN=y
+CONFIG_ARCH_HAS_TICK_BROADCAST=y
+CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
+CONFIG_ARCH_MULTIPLATFORM=y
+# CONFIG_ARCH_MULTI_CPU_AUTO is not set
+CONFIG_ARCH_MULTI_V6_V7=y
+CONFIG_ARCH_MULTI_V7=y
+CONFIG_ARCH_MXC=y
+CONFIG_ARCH_NR_GPIO=0
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
+CONFIG_ARCH_SUPPORTS_UPROBES=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARCH_USE_BUILTIN_BSWAP=y
+CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
+CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
+CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
+CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
+CONFIG_ARM=y
+# CONFIG_ARM_BIG_LITTLE_CPUFREQ is not set
+# CONFIG_ARM_CCI500_PMU is not set
+# CONFIG_ARM_CPU_SUSPEND is not set
+CONFIG_ARM_ERRATA_754322=y
+CONFIG_ARM_ERRATA_764369=y
+CONFIG_ARM_ERRATA_775420=y
+CONFIG_ARM_GIC=y
+CONFIG_ARM_HAS_SG_CHAIN=y
+CONFIG_ARM_HEAVY_MB=y
+CONFIG_ARM_IMX6Q_CPUFREQ=y
+CONFIG_ARM_L1_CACHE_SHIFT=6
+CONFIG_ARM_L1_CACHE_SHIFT_6=y
+# CONFIG_ARM_LPAE is not set
+CONFIG_ARM_PATCH_PHYS_VIRT=y
+CONFIG_ARM_PMU=y
+CONFIG_ARM_THUMB=y
+# CONFIG_ARM_THUMBEE is not set
+CONFIG_ARM_VIRT_EXT=y
+CONFIG_ATA=y
+CONFIG_ATAGS=y
+# CONFIG_ATA_SFF is not set
+CONFIG_AUTO_ZRELADDR=y
+CONFIG_CACHE_L2X0=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_CLKDEV_LOOKUP=y
+CONFIG_CLKSRC_IMX_GPT=y
+CONFIG_CLKSRC_MMIO=y
+CONFIG_CLKSRC_OF=y
+CONFIG_CLONE_BACKWARDS=y
+CONFIG_COMMON_CLK=y
+CONFIG_CPUFREQ_DT=y
+CONFIG_CPU_32v6K=y
+CONFIG_CPU_32v7=y
+CONFIG_CPU_ABRT_EV7=y
+# CONFIG_CPU_BPREDICT_DISABLE is not set
+CONFIG_CPU_CACHE_V7=y
+CONFIG_CPU_CACHE_VIPT=y
+CONFIG_CPU_COPY_V6=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+CONFIG_CPU_FREQ=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
+CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
+CONFIG_CPU_FREQ_GOV_COMMON=y
+CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+CONFIG_CPU_FREQ_GOV_POWERSAVE=y
+CONFIG_CPU_FREQ_GOV_USERSPACE=y
+CONFIG_CPU_FREQ_STAT=y
+CONFIG_CPU_FREQ_STAT_DETAILS=y
+CONFIG_CPU_HAS_ASID=y
+# CONFIG_CPU_ICACHE_DISABLE is not set
+CONFIG_CPU_PABRT_V7=y
+CONFIG_CPU_RMAP=y
+CONFIG_CPU_THERMAL=y
+CONFIG_CPU_TLB_V7=y
+CONFIG_CPU_V7=y
+CONFIG_CRC16=y
+CONFIG_CRYPTO_CRC32C=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_WORKQUEUE=y
+CONFIG_CRYPTO_XZ=y
+CONFIG_DCACHE_WORD_ACCESS=y
+CONFIG_DEBUG_IMX_UART_PORT=1
+CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
+# CONFIG_DEBUG_UART_8250 is not set
+# CONFIG_DEBUG_USER is not set
+CONFIG_DECOMPRESS_BZIP2=y
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_DECOMPRESS_LZO=y
+CONFIG_DECOMPRESS_XZ=y
+CONFIG_DMADEVICES=y
+CONFIG_DMA_ENGINE=y
+CONFIG_DMA_OF=y
+CONFIG_DTC=y
+# CONFIG_DW_DMAC_PCI is not set
+CONFIG_EDAC_ATOMIC_SCRUB=y
+CONFIG_EDAC_SUPPORT=y
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_FEC=y
+CONFIG_FIX_EARLYCON_MEM=y
+CONFIG_FRAME_POINTER=y
+# CONFIG_FSL_PQ_MDIO is not set
+CONFIG_FS_MBCACHE=y
+CONFIG_FS_POSIX_ACL=y
+CONFIG_GENERIC_ALLOCATOR=y
+CONFIG_GENERIC_BUG=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
+CONFIG_GENERIC_IDLE_POLL_SETUP=y
+CONFIG_GENERIC_IO=y
+CONFIG_GENERIC_IRQ_CHIP=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
+CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GENERIC_SCHED_CLOCK=y
+CONFIG_GENERIC_SMP_IDLE_THREAD=y
+CONFIG_GENERIC_STRNCPY_FROM_USER=y
+CONFIG_GENERIC_STRNLEN_USER=y
+# CONFIG_GIANFAR is not set
+CONFIG_GLOB=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_DEVRES=y
+CONFIG_GPIO_GENERIC=y
+CONFIG_GPIO_MXC=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_HANDLE_DOMAIN_IRQ=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT_MAP=y
+# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
+CONFIG_HAVE_ARCH_AUDITSYSCALL=y
+CONFIG_HAVE_ARCH_BITREVERSE=y
+CONFIG_HAVE_ARCH_JUMP_LABEL=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_HAVE_ARCH_PFN_VALID=y
+CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
+CONFIG_HAVE_ARCH_TRACEHOOK=y
+CONFIG_HAVE_ARM_SCU=y
+CONFIG_HAVE_ARM_TWD=y
+# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
+CONFIG_HAVE_BPF_JIT=y
+CONFIG_HAVE_CC_STACKPROTECTOR=y
+CONFIG_HAVE_CLK=y
+CONFIG_HAVE_CLK_PREPARE=y
+CONFIG_HAVE_CONTEXT_TRACKING=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_HAVE_DEBUG_KMEMLEAK=y
+CONFIG_HAVE_DMA_API_DEBUG=y
+CONFIG_HAVE_DMA_ATTRS=y
+CONFIG_HAVE_DMA_CONTIGUOUS=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_HAVE_HW_BREAKPOINT=y
+CONFIG_HAVE_IDE=y
+CONFIG_HAVE_IMX_ANATOP=y
+CONFIG_HAVE_IMX_GPC=y
+CONFIG_HAVE_IMX_MMDC=y
+CONFIG_HAVE_IMX_SRC=y
+CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_LZ4=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_HAVE_KERNEL_LZO=y
+CONFIG_HAVE_KERNEL_XZ=y
+CONFIG_HAVE_MEMBLOCK=y
+CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
+CONFIG_HAVE_NET_DSA=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_OPTPROBES=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_HAVE_PERF_REGS=y
+CONFIG_HAVE_PERF_USER_STACK_DUMP=y
+CONFIG_HAVE_PROC_CPU=y
+CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
+CONFIG_HAVE_SMP=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
+CONFIG_HAVE_UID16=y
+CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
+# CONFIG_HSU_DMA_PCI is not set
+CONFIG_HZ_FIXED=0
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_IMX=y
+CONFIG_IMX2_WDT=y
+CONFIG_IMX_DMA=y
+CONFIG_IMX_SDMA=y
+CONFIG_IMX_THERMAL=y
+# CONFIG_IMX_WEIM is not set
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_IOMMU_HELPER=y
+CONFIG_IRQCHIP=y
+CONFIG_IRQ_DOMAIN=y
+CONFIG_IRQ_DOMAIN_HIERARCHY=y
+CONFIG_IRQ_FORCED_THREADING=y
+CONFIG_IRQ_WORK=y
+CONFIG_JBD2=y
+CONFIG_LIBFDT=y
+CONFIG_LOCK_SPIN_ON_OWNER=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_MDIO_BOARDINFO=y
+CONFIG_MFD_SYSCON=y
+CONFIG_MIGHT_HAVE_CACHE_L2X0=y
+CONFIG_MIGHT_HAVE_PCI=y
+CONFIG_MMC=y
+CONFIG_MMC_BLOCK=y
+# CONFIG_MMC_MXC is not set
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ESDHC_IMX=y
+CONFIG_MMC_SDHCI_IO_ACCESSORS=y
+# CONFIG_MMC_SDHCI_PCI is not set
+CONFIG_MMC_SDHCI_PLTFM=y
+# CONFIG_MMC_TIFM_SD is not set
+CONFIG_MODULES_TREE_LOOKUP=y
+CONFIG_MODULES_USE_ELF_REL=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ECC=y
+CONFIG_MTD_NAND_GPMI_NAND=y
+# CONFIG_MTD_PHYSMAP_OF is not set
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_BEB_LIMIT=20
+CONFIG_MTD_UBI_BLOCK=y
+# CONFIG_MTD_UBI_FASTMAP is not set
+# CONFIG_MTD_UBI_GLUEBI is not set
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MULTI_IRQ_HANDLER=y
+CONFIG_MUTEX_SPIN_ON_OWNER=y
+# CONFIG_MX3_IPU is not set
+CONFIG_MXS_DMA=y
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NEON=y
+CONFIG_NET_FLOW_LIMIT=y
+CONFIG_NET_PTP_CLASSIFY=y
+CONFIG_NLS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NO_BOOTMEM=y
+CONFIG_NO_HZ_COMMON=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_NR_CPUS=4
+CONFIG_OF=y
+CONFIG_OF_ADDRESS=y
+CONFIG_OF_ADDRESS_PCI=y
+CONFIG_OF_EARLY_FLATTREE=y
+CONFIG_OF_FLATTREE=y
+CONFIG_OF_GPIO=y
+CONFIG_OF_IRQ=y
+CONFIG_OF_MDIO=y
+CONFIG_OF_MTD=y
+CONFIG_OF_NET=y
+CONFIG_OF_PCI=y
+CONFIG_OF_PCI_IRQ=y
+CONFIG_OF_RESERVED_MEM=y
+CONFIG_OLD_SIGACTION=y
+CONFIG_OLD_SIGSUSPEND3=y
+CONFIG_OUTER_CACHE=y
+CONFIG_OUTER_CACHE_SYNC=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_PAGE_OFFSET=0x80000000
+CONFIG_PCI=y
+CONFIG_PCIEAER=y
+CONFIG_PCIEPORTBUS=y
+CONFIG_PCIE_DW=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_DOMAINS_GENERIC=y
+CONFIG_PCI_IMX6=y
+CONFIG_PERF_EVENTS=y
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PGTABLE_LEVELS=2
+CONFIG_PHYLIB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX=y
+CONFIG_PINCTRL_IMX6Q=y
+CONFIG_PINCTRL_IMX6SL=y
+CONFIG_PINCTRL_IMX6SX=y
+CONFIG_PINCTRL_IMX6UL=y
+# CONFIG_PINCTRL_SINGLE is not set
+CONFIG_PL310_ERRATA_588369=y
+CONFIG_PL310_ERRATA_727915=y
+# CONFIG_PL310_ERRATA_753970 is not set
+CONFIG_PL310_ERRATA_769419=y
+CONFIG_PM_OPP=y
+CONFIG_PPS=y
+CONFIG_PTP_1588_CLOCK=y
+CONFIG_RAS=y
+CONFIG_RATIONAL=y
+CONFIG_RCU_STALL_COMMON=y
+CONFIG_RD_BZIP2=y
+CONFIG_RD_GZIP=y
+CONFIG_RD_LZO=y
+CONFIG_RD_XZ=y
+CONFIG_REGMAP=y
+CONFIG_REGMAP_I2C=y
+CONFIG_REGMAP_MMIO=y
+CONFIG_REGMAP_SPI=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_ANATOP=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_PFUZE100=y
+CONFIG_RFS_ACCEL=y
+CONFIG_RPS=y
+CONFIG_RTC_CLASS=y
+# CONFIG_RTC_DRV_IMXDI is not set
+# CONFIG_RTC_DRV_MXC is not set
+CONFIG_RWSEM_SPIN_ON_OWNER=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_SATA_AHCI_PLATFORM=y
+CONFIG_SCHED_HRTICK=y
+# CONFIG_SCHED_INFO is not set
+CONFIG_SCSI=y
+CONFIG_SERIAL_IMX=y
+CONFIG_SERIAL_IMX_CONSOLE=y
+# CONFIG_SG_SPLIT is not set
+CONFIG_SMP=y
+CONFIG_SMP_ON_UP=y
+CONFIG_SOC_BUS=y
+# CONFIG_SOC_IMX50 is not set
+# CONFIG_SOC_IMX51 is not set
+# CONFIG_SOC_IMX53 is not set
+CONFIG_SOC_IMX6=y
+CONFIG_SOC_IMX6Q=y
+CONFIG_SOC_IMX6SL=y
+CONFIG_SOC_IMX6SX=y
+CONFIG_SOC_IMX6UL=y
+# CONFIG_SOC_IMX7D is not set
+# CONFIG_SOC_LS1021A is not set
+# CONFIG_SOC_VF610 is not set
+CONFIG_SPARSE_IRQ=y
+CONFIG_SPI=y
+CONFIG_SPI_BITBANG=y
+CONFIG_SPI_IMX=y
+CONFIG_SPI_MASTER=y
+CONFIG_SRAM=y
+CONFIG_SRCU=y
+CONFIG_STMP_DEVICE=y
+CONFIG_STOP_MACHINE=y
+# CONFIG_SUNXI_SRAM is not set
+CONFIG_SWIOTLB=y
+CONFIG_SWP_EMULATE=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_THERMAL=y
+# CONFIG_THERMAL_DEFAULT_GOV_FAIR_SHARE is not set
+# CONFIG_THERMAL_DEFAULT_GOV_POWER_ALLOCATOR is not set
+CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
+# CONFIG_THERMAL_DEFAULT_GOV_USER_SPACE is not set
+# CONFIG_THERMAL_EMULATION is not set
+# CONFIG_THERMAL_GOV_FAIR_SHARE is not set
+# CONFIG_THERMAL_GOV_POWER_ALLOCATOR is not set
+CONFIG_THERMAL_GOV_STEP_WISE=y
+# CONFIG_THERMAL_GOV_USER_SPACE is not set
+CONFIG_THERMAL_OF=y
+CONFIG_THERMAL_WRITABLE_TRIPS=y
+# CONFIG_THUMB2_KERNEL is not set
+CONFIG_TICK_CPU_ACCOUNTING=y
+CONFIG_TREE_RCU=y
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_UBIFS_FS_LZO=y
+CONFIG_UBIFS_FS_XZ=y
+CONFIG_UBIFS_FS_ZLIB=y
+CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
+# CONFIG_USB_MXS_PHY is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USE_OF=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_VFP=y
+CONFIG_VFPv3=y
+CONFIG_VMSPLIT_2G=y
+# CONFIG_VMSPLIT_3G is not set
+CONFIG_WATCHDOG_CORE=y
+CONFIG_XPS=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_BCJ=y
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZONE_DMA_FLAG=0
diff --git a/target/linux/imx6/files-4.3/drivers/net/phy/gw16083.c b/target/linux/imx6/files-4.3/drivers/net/phy/gw16083.c
new file mode 100644
index 0000000..bdc7446
--- /dev/null
+++ b/target/linux/imx6/files-4.3/drivers/net/phy/gw16083.c
@@ -0,0 +1,1046 @@
+/*
+ * drivers/net/phy/gw16083.c
+ *
+ * Driver for GW16083 Ventana Ethernet Expansion Mezzanine
+ *
+ * Author: Tim Harvey
+ *
+ * Copyright (c) 2014 Tim Harvey <tharvey at gateworks.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ */
+
+/*
+ * The GW16083 interfaces with a Ventana baseboard via the PCIe bus, an i2c
+ * bus (i2c2), and a couple of GPIO's. On the PCIe bus is an i210 GigE with
+ * its MAC connected to Port4 of a Marvell MV88E6176 7-port GigE switch via
+ * MDIO and RGMII. Ports 0-3 are standard copper RJ45 but Ports 5 and 6
+ * connect to Marvell MV88E1111 dual-mode Copper/Fiber PHY's over SGMII and
+ * MDIO. The PHY's have both an RG45 for copper and an SFP module.
+ */
+
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/errno.h>
+#include <linux/unistd.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/phy.h>
+#include <linux/marvell_phy.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+
+#include <linux/io.h>
+#include <asm/irq.h>
+#include <net/dsa.h>
+#include <linux/uaccess.h>
+
+#include "gw16083.h"
+
+#undef FAIL_ON_CHECKSUM_ERR	/* fail to configure SFP if checksum bad */
+#define PORT_POWER_CONTROL	/* ports can be enabled/disabled via sysfs */
+#define PORT_MODE_CONTROL	/* ports 5/6 can have SFP/RJ45 mode forced */
+#define RGMII_DELAY_ON_PHY	/* implement Port5/6 tx/rx delay on PHY vs sw */
+
+MODULE_DESCRIPTION("GW16083 driver");
+MODULE_AUTHOR("Tim Harvey");
+MODULE_LICENSE("GPL");
+
+struct mv88e1111_port_state {
+	int port;
+	bool present;
+	bool serdes;
+	bool sfp_signal;
+	bool sfp_present;
+	bool sfp_compat;
+	bool sfp_enabled;
+	char sfp_id[64];
+};
+
+struct mv88e1111_priv {
+	struct phy_device		*phydev;
+	struct i2c_client		*client;
+	struct mv88e1111_port_state	port5;
+	struct mv88e1111_port_state	port6;
+	struct kobject			*sysfs_kobj;
+	struct delayed_work work;
+	struct workqueue_struct *workq;
+};
+
+enum {
+	mode_copper = 0,
+	mode_serdes = 1,
+};
+
+#if IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
+static struct dsa_chip_data switch_chip_data = {
+	.port_names = {
+		"lan4",
+		"lan3",
+		"lan2",
+		"lan1",
+		"cpu",
+		"lan5",
+		"lan6",
+	},
+};
+
+static struct dsa_platform_data switch_plat_data = {
+	.nr_chips       = 1,
+	.chip           = &switch_chip_data,
+};
+
+static struct platform_device switch_device = {
+	.name           = "dsa",
+	.id             = 0,
+	.num_resources  = 0,
+	.dev.platform_data = &switch_plat_data,
+};
+#endif
+
+static struct i2c_client *gw16083_client = NULL;
+
+static int gw16083_read_port_sfp(struct i2c_client *client,
+				 struct mv88e1111_port_state *state);
+
+/* read switch port register from port0-6 */
+u16 read_switch_port(struct phy_device *pdev, int port, u8 regaddr)
+{
+	return pdev->bus->read(pdev->bus, MV_BASE + port, regaddr);
+}
+
+/* write switch port register to port0-6 */
+int write_switch_port(struct phy_device *pdev, int port, u8 regaddr, u16 val)
+{
+	return pdev->bus->write(pdev->bus, MV_BASE + port, regaddr, val);
+}
+
+/*
+ * read_switch_port_phy - write a register for a specific port on 88E6176
+ * The 88E6176 PHY registers must be accessed thorugh the Global2 address
+ * using the SMI_PHY_COMMAND_REG and SMI_PHY_DATA_REG.
+ */
+int read_switch_port_phy(struct phy_device *pdev, int port, u8 regaddr)
+{
+	struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
+	u16 reg;
+	int i;
+
+	dev_dbg(&priv->client->dev, "read_phy: port%d reg=0x%02x\n", port,
+		regaddr);
+	reg = SMIBUSY | SMIMODE22 | SMIOP_READ;
+	reg |= port << DEVADDR;
+	reg |= regaddr << REGADDR;
+	pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SMI_PHY_COMMAND, reg);
+	for (i = 0; i < 10; i++) {
+		reg = pdev->bus->read(pdev->bus, MV_GLOBAL2,
+				      MV_SMI_PHY_COMMAND);
+		if (!(reg & (1<<15)))
+			break;
+		mdelay(1);
+	}
+	/* timeout */
+	if (i == 10)
+		return 0xffff;
+	reg = pdev->bus->read(pdev->bus, MV_GLOBAL2, MV_SMI_PHY_DATA);
+	return reg;
+}
+
+/*
+ * write_switch_port_phy - write a register for a specific port on 88E6176
+ * The 88E6176 PHY registers must be accessed thorugh the Global2 address
+ * using the SMI_PHY_COMMAND_REG and SMI_PHY_DATA_REG.
+ */
+int write_switch_port_phy(struct phy_device *pdev, int port, u8 addr, u16 reg)
+{
+	struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
+	int i;
+
+	dev_dbg(&priv->client->dev, "write_phy: port%d reg=0x%02x val=0x%04x\n",
+		port, addr, reg);
+	pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SMI_PHY_DATA, reg);
+	reg = SMIBUSY | SMIMODE22 | SMIOP_WRITE;
+	reg |= port << DEVADDR;
+	reg |= addr << REGADDR;
+	pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SMI_PHY_COMMAND, reg);
+	for (i = 0; i < 10; i++) {
+		reg = pdev->bus->read(pdev->bus, MV_GLOBAL2,
+				      MV_SMI_PHY_COMMAND);
+		if (!(reg & (1<<15)))
+			break;
+		mdelay(1);
+	}
+	/* timeout */
+	if (i == 10)
+		return -ETIMEDOUT;
+
+	return 0;
+}
+
+/* read a scratch register from switch */
+inline u8 read_switch_scratch(struct phy_device *pdev, u8 reg)
+{
+	pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SCRATCH_MISC, (reg << 8));
+	return pdev->bus->read(pdev->bus, MV_GLOBAL2, MV_SCRATCH_MISC) & 0xff;
+}
+
+/* write a scratch register to switch */
+inline void write_switch_scratch(struct phy_device *pdev, u8 reg, u8 val)
+{
+	pdev->bus->write(pdev->bus, MV_GLOBAL2, MV_SCRATCH_MISC,
+			 (1 << 15) | (reg << 8) | val);
+}
+
+/* enable or disable an SFP's TXEN signal */
+static int enable_sfp_txen(struct phy_device *pdev, int port, bool enable)
+{
+	struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
+	u8 gpio;
+	int bit;
+
+	if (port != 5 && port != 6)
+		return -EINVAL;
+
+	/* GPIO[2:1] output low to enable TXEN */
+	bit = (port == 5) ? 1 : 2;
+	gpio = read_switch_scratch(pdev, MV_GPIO_DATA);
+	if (enable)
+		gpio |= (1 << bit);
+	else
+		gpio &= (1 << bit);
+	write_switch_scratch(pdev, MV_GPIO_DATA, gpio);
+	dev_info(&priv->client->dev, "Port%d: SFP TX %s\n", port, enable ?
+		 "enabled" : "disabled");
+	return 0;
+}
+
+/* configure mv88e1111 port for copper or serdes
+ *  For Copper we set auto link/duplex/speed detection
+ *  For SerDes/Fiber we force 1000mbps link up and auto-neg duplex
+ */
+static int config_mv88e1111_port_sfp(struct phy_device *pdev, int port,
+				     bool sfp)
+{
+	struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
+	u16 reg;
+
+	if (port != 5 && port != 6)
+		return -EINVAL;
+
+	dev_dbg(&priv->client->dev, "%s: Port%d %s\n", __func__, port,
+		sfp ? "SFP" : "copper");
+	if (sfp) {
+		enable_sfp_txen(pdev, port, 1);
+
+		/* configure MV88E6176 Physical Control Port Register */
+		dev_info(&priv->client->dev,
+			 "Port%d: SFP: force 1000mbps link up "
+			 "(auto-negotiate duplex)\n",
+			 port);
+		reg = read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL);
+		reg &= ~0x3f; /* clear 5-0 */
+		reg |= (1 << 4) | (1 << 5); /* force link up */
+		reg |= 2; /* force 1000mbps */
+		write_switch_port(pdev, port, MV_PORT_PHYS_CONTROL, reg);
+		reg = read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL);
+	}
+
+	/* copper */
+	else {
+		enable_sfp_txen(pdev, port, 0);
+
+		/* configure MV88E6176 Physical Control Port Register */
+		dev_info(&priv->client->dev,
+			 "Port%d: Copper: set auto-neg link/duplex/speed\n",
+			 port);
+		reg = read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL);
+		reg &= ~0x3f; /* clear 5-0 */
+		reg |= 3; /* speed not forced */
+		write_switch_port(pdev, port, MV_PORT_PHYS_CONTROL, reg);
+		reg = read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL);
+	}
+	dev_dbg(&priv->client->dev, "%s: Port%d %s PORT_PHYS_CONTROL=0x%04x\n",
+		__func__, port, sfp ? "SFP" : "copper",
+		read_switch_port(pdev, port, MV_PORT_PHYS_CONTROL));
+
+	return 0;
+}
+
+#if !IS_ENABLED(CONFIG_NET_DSA_MV88E6352) && defined(PORT_POWER_CONTROL)
+static int enable_switch_port(struct phy_device *pdev, int port, bool enable)
+{
+	struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
+	u16 reg;
+
+	/* power up port */
+	dev_info(&priv->client->dev, "Port%d: %s\n", port,
+		 enable ? "normal operation" : "power down");
+	reg = read_switch_port_phy(pdev, port, MV_PHY_CONTROL);
+	if (enable)
+		reg &= ~(1 << 11);	/* Normal Operation */
+	else
+		reg |= (1 << 11);	/* power down */
+	write_switch_port_phy(pdev, port, MV_PHY_CONTROL, reg);
+
+	reg = read_switch_port_phy(pdev, port, MV_PHY_CONTROL1);
+	if (enable)
+		reg &= ~(1 << 2);	/* Normal Operation */
+	else
+		reg |= (1 << 2);	/* power down */
+	write_switch_port_phy(pdev, port, MV_PHY_CONTROL1, reg);
+
+	return 0;
+}
+#endif
+
+/*
+ * Sysfs API
+ */
+
+struct mv88e1111_port_state *get_port_state(struct mv88e1111_priv *priv,
+					    int port)
+{
+	if (port == 5)
+		return &priv->port5;
+	if (port == 6)
+		return &priv->port6;
+	return NULL;
+}
+
+/*
+ * get MV88E6176 port number for a specific GW16083 port name
+ *  The GW16083 ports as shown on the silkscreen are not mapped according to
+ *  the MV88E6176 ports numbers.
+ */
+static int gw16083_get_port(const char* name)
+{
+	int i;
+	int map[] = { 3, 2, 1, 0, 5, 6 };
+
+	if (strncasecmp(name, "LAN", 3) != 0)
+		return -1;
+	i = name[3] - '0';
+	if (i < 1 || i > 6)
+		return -1;
+	return map[i-1];
+}
+
+#if !IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
+static ssize_t port_show(struct device *dev, struct device_attribute *attr,
+			 char *buf)
+{
+	struct mv88e1111_priv *priv = dev_get_drvdata(dev);
+	int port = -1;
+	u16 reg;
+
+	if (sscanf(attr->attr.name, "port%d", &port) != 1)
+		return 0;
+	if (port < 0 || port > 6)
+		return 0;
+	reg = read_switch_port_phy(priv->phydev, port, MV_PHY_CONTROL);
+	return sprintf(buf, "%s\n", (reg & (1 << 11)) ? "disabled" : "enabled");
+}
+
+#if defined(PORT_POWER_CONTROL)
+static ssize_t port_store(struct device *dev, struct device_attribute *attr,
+			  const char *buf, size_t count)
+{
+	struct mv88e1111_priv *priv = dev_get_drvdata(dev);
+	int port = -1;
+	int val;
+
+	port = gw16083_get_port(attr->attr.name);
+	if (port < 0)
+		return 0;
+	if (sscanf(buf, "%d", &val) != 1)
+		return 0;
+	enable_switch_port(priv->phydev, port, val ? 1 : 0);
+	return count;
+}
+
+static DEVICE_ATTR(lan1, S_IWUSR | S_IRUGO, port_show, port_store);
+static DEVICE_ATTR(lan2, S_IWUSR | S_IRUGO, port_show, port_store);
+static DEVICE_ATTR(lan3, S_IWUSR | S_IRUGO, port_show, port_store);
+static DEVICE_ATTR(lan4, S_IWUSR | S_IRUGO, port_show, port_store);
+static DEVICE_ATTR(lan5, S_IWUSR | S_IRUGO, port_show, port_store);
+static DEVICE_ATTR(lan6, S_IWUSR | S_IRUGO, port_show, port_store);
+#else
+static DEVICE_ATTR(lan1, S_IRUGO, port_show, NULL);
+static DEVICE_ATTR(lan2, S_IRUGO, port_show, NULL);
+static DEVICE_ATTR(lan3, S_IRUGO, port_show, NULL);
+static DEVICE_ATTR(lan4, S_IRUGO, port_show, NULL);
+static DEVICE_ATTR(lan5, S_IRUGO, port_show, NULL);
+static DEVICE_ATTR(lan6, S_IRUGO, port_show, NULL);
+#endif
+#endif /* #if IS_ENABLED(CONFIG_NET_DSA_MV88E6352) */
+
+static ssize_t portmode_show(struct device *dev, struct device_attribute *attr,
+			     char *buf)
+{
+	struct mv88e1111_priv *priv = dev_get_drvdata(dev);
+	struct mv88e1111_port_state *state;
+
+	state = get_port_state(priv, gw16083_get_port(attr->attr.name));
+	if (!state)
+		return 0;
+
+	return sprintf(buf, "%s\n", state->serdes ? "SFP" : "RJ45");
+}
+#ifdef PORT_MODE_CONTROL
+static ssize_t portmode_store(struct device *dev, struct device_attribute *attr,
+			      const char *buf, size_t count)
+{
+	struct mv88e1111_priv *priv = dev_get_drvdata(dev);
+	struct mv88e1111_port_state *state;
+	u16 reg;
+	int port;
+
+	port = gw16083_get_port(attr->attr.name);
+	state = get_port_state(priv, port);
+	if (!state)
+		return 0;
+
+	reg = read_switch_port_phy(priv->phydev, port, MII_M1111_PHY_EXT_SR);
+	if (strcasecmp(buf, "auto") == 0) {
+		reg &= ~(1<<15); /* enable auto-selection */
+		dev_info(&priv->client->dev, "Port%d: enable auto-selection\n",
+			 port);
+	} else if (strcasecmp(buf, "RJ45") == 0) {
+		reg |= (1<<15); /* disable auto-selection */
+		reg |= 0xb; /* RGMII to Copper */
+		config_mv88e1111_port_sfp(priv->phydev, port, 0);
+		dev_info(&priv->client->dev, "Port%d: select RJ45\n", port);
+	} else if (strcasecmp(buf, "SFP") == 0) {
+		reg |= (1<<15); /* disable auto-selection */
+		reg |= 0x3; /* RGMII to Fiber */
+		config_mv88e1111_port_sfp(priv->phydev, port, 1);
+		dev_info(&priv->client->dev, "Port%d: select SFP\n", port);
+	}
+	write_switch_port_phy(priv->phydev, port, MII_M1111_PHY_EXT_SR, reg);
+
+	return count;
+}
+
+static DEVICE_ATTR(lan5_mode, S_IWUSR | S_IRUGO, portmode_show, portmode_store);
+static DEVICE_ATTR(lan6_mode, S_IWUSR | S_IRUGO, portmode_show, portmode_store);
+#else
+static DEVICE_ATTR(lan5_mode, S_IRUGO, portmode_show, NULL);
+static DEVICE_ATTR(lan6_mode, S_IRUGO, portmode_show, NULL);
+#endif
+
+static ssize_t portsfp_show(struct device *dev, struct device_attribute *attr,
+			     char *buf)
+{
+	struct mv88e1111_priv *priv = dev_get_drvdata(dev);
+	struct mv88e1111_port_state *state;
+
+	state = get_port_state(priv, gw16083_get_port(attr->attr.name));
+	if (!state)
+		return 0;
+
+	if (!state->sfp_present)
+		return 0;
+
+	return sprintf(buf, "%s\n", state->sfp_id);
+}
+
+static DEVICE_ATTR(lan5_sfp, S_IRUGO, portsfp_show, NULL);
+static DEVICE_ATTR(lan6_sfp, S_IRUGO, portsfp_show, NULL);
+
+/*
+ * PHY driver
+ */
+
+/* check MV88E1111 PHY status and MV88E6176 GPIO */
+static void
+mv88e6176_work(struct work_struct *work)
+{
+	struct mv88e1111_priv *priv =
+		container_of(work, struct mv88e1111_priv, work.work);
+	struct phy_device *pdev = priv->phydev;
+	struct device *dev = &priv->client->dev;
+	struct mv88e1111_port_state *state;
+	bool serdes, sfp_present, sfp_signal;
+	int port;
+	u16 gpio;
+
+	mutex_lock(&pdev->lock);
+	gpio = read_switch_scratch(pdev, MV_GPIO_DATA);
+	for (port = 5; port < 7; port++) {
+		serdes = (read_switch_port_phy(pdev, port, MII_M1111_PHY_EXT_SR)
+			 & (1<<13)) ? 1 : 0;
+		dev_dbg(dev, "%s: Port%d GPIO:0x%02x SerDes:%d\n",
+			__func__, port, gpio, serdes);
+		switch(port) {
+		case 5:
+			state = &priv->port5;
+			sfp_present = !((gpio >> 5) & 1);
+			sfp_signal = !((gpio >> 6) & 1);
+			break;
+		case 6:
+			state = &priv->port6;
+			sfp_present = !((gpio >> 3) & 1);
+			sfp_signal = !((gpio >> 4) & 1);
+			break;
+		}
+
+		/*
+		 * on sfp_detect read/verify SFP MSA and set sfp_compat
+		 * on sfp_signal issue link down?
+		 * on serdes auto-select
+		 */
+		if (state->sfp_present != sfp_present) {
+			state->sfp_present = sfp_present;
+			dev_info(dev, "Port%d: SFP %s\n",
+				 port, sfp_present ? "inserted" : "removed");
+			if (state->sfp_present) {
+				if (gw16083_read_port_sfp(priv->client, state))
+					state->sfp_compat = false;
+				else
+					state->sfp_compat = true;
+				/* trigger a re-select/enable below */
+				state->serdes = !serdes;
+				pdev->state = PHY_RUNNING;
+			} else {
+				state->sfp_compat = false;
+				state->sfp_enabled = false;
+				pdev->state = PHY_NOLINK;
+			}
+		}
+		if (state->sfp_signal != sfp_signal) {
+			state->sfp_signal = sfp_signal;
+			dev_info(dev, "Port%d: SFP signal %s\n",
+				 port, sfp_signal ? "detected" : "lost");
+		}
+		if (state->serdes != serdes) {
+			state->serdes = serdes;
+			dev_info(dev, "Port%d: %s auto-selected\n",
+				 port, serdes ? "SERDES" : "copper");
+
+			/*
+			 * if auto-selection has switched to copper
+			 * disable serdes
+			 */
+			if (!serdes) {
+				config_mv88e1111_port_sfp(pdev, port, 0);
+				state->sfp_enabled = false;
+			}
+		}
+
+		/* if compatible SFP module and not yet enabled then enable */
+		if (state->sfp_compat && state->sfp_signal &&
+		    !state->sfp_enabled)
+		{
+			if (!config_mv88e1111_port_sfp(pdev, port, 1))
+				state->sfp_enabled = true;
+		}
+	}
+	mutex_unlock(&pdev->lock);
+
+	queue_delayed_work(priv->workq, &priv->work, HZ);
+}
+
+static int
+mv88e6176_read_status(struct phy_device *pdev)
+{
+	return 0;
+}
+
+static int
+mv88e6176_config_aneg(struct phy_device *pdev)
+{
+	return 0;
+}
+
+static int
+mv88e6176_config_init(struct phy_device *pdev)
+{
+	pdev->state = PHY_RUNNING;
+
+	return 0;
+}
+
+static void
+mv88e6176_remove(struct phy_device *pdev)
+{
+	struct mv88e1111_priv *priv = dev_get_drvdata(&pdev->dev);
+
+	dev_dbg(&priv->client->dev, "%s", __func__);
+
+	destroy_workqueue(priv->workq);
+#if !IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
+	device_remove_file(&pdev->dev, &dev_attr_lan1);
+	device_remove_file(&pdev->dev, &dev_attr_lan2);
+	device_remove_file(&pdev->dev, &dev_attr_lan3);
+	device_remove_file(&pdev->dev, &dev_attr_lan4);
+	device_remove_file(&pdev->dev, &dev_attr_lan5);
+	device_remove_file(&pdev->dev, &dev_attr_lan6);
+#endif
+	device_remove_file(&pdev->dev, &dev_attr_lan5_sfp);
+	device_remove_file(&pdev->dev, &dev_attr_lan6_sfp);
+	device_remove_file(&pdev->dev, &dev_attr_lan5_mode);
+	device_remove_file(&pdev->dev, &dev_attr_lan6_mode);
+	sysfs_remove_link(kernel_kobj, "gw16083");
+}
+
+/*
+ * mv88e6176_probe - called any time an MV88E6176 is found on an mdio bus
+ *  Determine if this MV88E6176 is indeed on a GW16083 and if so configure
+ *  the port5/port6 phy and register a background procedure for monitoring
+ *  their states to support SFP vs Copper switching.
+ *
+ * Verify this is a GW16083 by ensuring:
+ *   - the phy address matches that of a GW16083
+ *   - the mdio bus is from an i210 device (igb driver)
+ *   - there are MV881111 PHY's hanging off of Port5 and Port6
+ */
+static int
+mv88e6176_probe(struct phy_device *pdev)
+{
+	int port;
+	int ret = 0;
+	u32 id, reg;
+	struct mv88e1111_priv *priv;
+	struct device *dev;
+#if IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
+	struct net_device *netdev = NULL;
+#endif
+
+	dev_dbg(&pdev->dev, "%s: addr=0x%02x bus=%s:%s gw16083_client=%p\n",
+		__func__, pdev->addr, pdev->bus->name, pdev->bus->id,
+		gw16083_client);
+
+	/* In single-chip addressing mode the MV88E6176 shows up on 0x10-0x16 */
+	if (pdev->addr != MV_BASE)
+		return 0;
+
+	/* i2c driver needs to be loaded first */
+	if (!gw16083_client)
+		return 0;
+	dev = &gw16083_client->dev;
+
+	/* gw16083 has MV88E1676 hanging off of i210 mdio bus */
+	if (strcmp(pdev->bus->name, "igb_enet_mii_bus") != 0)
+		return 0;
+
+	/* verify Port5/Port6 have an MV88E1111 PHY hanging off them */
+	for (port = 5; port < 7; port++) {
+		id = read_switch_port_phy(pdev, port,
+					  MII_M1111_PHY_IDENT0) << 16;
+		id |= read_switch_port_phy(pdev, port, MII_M1111_PHY_IDENT1);
+		if ((id & MII_M1111_PHY_ID_MASK) != MII_M1111_PHY_ID) {
+			dev_err(dev, "Port%d: No MV88E1111 PHY detected", port);
+			return 0;
+		}
+	}
+
+#if IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
+	/*
+	 * Find the netdev this bus is hanging off of and register with DSA:
+	 *  The netdev must be an Intel I210 (igb) with Gateworks MAC addr
+	 */
+	read_lock(&dev_base_lock);
+	for_each_netdev(&init_net, netdev) {
+		if (netdev->dev.parent &&
+		    !strcmp(netdev->dev.parent->driver->name, "igb") &&
+		    (netdev->perm_addr[0] == 0x00) &&
+		    (netdev->perm_addr[1] == 0xd0) &&
+		    (netdev->perm_addr[2] == 0x12))
+		{
+			switch_plat_data.netdev = &netdev->dev;
+			switch_plat_data.chip[0].host_dev = &pdev->bus->dev;
+			break;
+		}
+	}
+	read_unlock(&dev_base_lock);
+
+	if (switch_plat_data.netdev) {
+		platform_device_register(&switch_device);
+		dev_info(dev, "registered GW16083 DSA switch\n");
+	} else {
+		dev_err(dev, "failed to find netdev for DSA switch\n");
+	}
+#endif
+
+	/*
+	 * port5/6 config: MV88E1111 PHY
+	 * Register 20: PHY Control Register
+	 *   R20_7: add delay to RX_CLK for RXD
+	 *   R20_1: add delay to TX_CLK for TXD
+	 * Register 24: LED Control Register
+	 *   0x4111:
+	 *     Pulse stretch 170 to 340 ms
+	 * Register 0: Control Register
+	 *   R0_15: phy reset
+	 */
+	dev_info(dev, "Configuring MV88E6176 7-port switch");
+	for (port = 5; port < 7; port++) {
+#ifdef RGMII_DELAY_ON_PHY
+		/* phy rx/tx delay */
+		reg = read_switch_port_phy(pdev, port, MII_M1111_PHY_EXT_CR);
+		reg |= (1<<1) | (1<<7);
+		write_switch_port_phy(pdev, port, MII_M1111_PHY_EXT_CR, reg);
+#else
+		write_switch_port(pdev, port, MV_PORT_PHYS_CONTROL, 0xC003);
+#endif
+
+		/* led config */
+		write_switch_port_phy(pdev, port, MII_M1111_PHY_LED_CONTROL,
+				      MII_M1111_PHY_LED_PULSE_STR);
+		/* reset phy */
+		reg = read_switch_port_phy(pdev, port, MII_M1111_PHY_CONTROL);
+		reg |= MII_M1111_PHY_CONTROL_RESET;
+		write_switch_port_phy(pdev, port, MII_M1111_PHY_CONTROL, reg);
+		dev_info(dev, "Port%d: MV88E111 PHY configured\n", port);
+	}
+
+	/*
+	 * GPIO Configuration:
+	 *  GPIO1: FIB5_TXEN# (output)
+	 *  GPIO2: FIB6_TXEN# (output)
+	 *  GPIO3: FIB6_PRES# (input)
+	 *  GPIO4: FIB6_LOS   (input)
+	 *  GPIO5: FIB5_PRES# (input)
+	 *  GPIO6: FIB5_LOS   (input)
+	 */
+	write_switch_scratch(pdev, MV_GPIO_DATA, 0x06); /* GPIO[2:1] out hi */
+	write_switch_scratch(pdev, MV_GPIO_DIR,  0x78); /* GPIO[6:3] inp */
+
+	pdev->irq = PHY_POLL;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+	memset(priv, 0, sizeof(*priv));
+	priv->phydev = pdev;
+	priv->client = gw16083_client;
+	priv->port5.port = 5;
+	priv->port6.port = 6;
+	dev_set_drvdata(&pdev->dev, priv);
+
+	/* register sysfs API */
+#if !IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
+	ret |= device_create_file(&pdev->dev, &dev_attr_lan1);
+	ret |= device_create_file(&pdev->dev, &dev_attr_lan2);
+	ret |= device_create_file(&pdev->dev, &dev_attr_lan3);
+	ret |= device_create_file(&pdev->dev, &dev_attr_lan4);
+	ret |= device_create_file(&pdev->dev, &dev_attr_lan5);
+	ret |= device_create_file(&pdev->dev, &dev_attr_lan6);
+#endif
+	ret |= device_create_file(&pdev->dev, &dev_attr_lan5_sfp);
+	ret |= device_create_file(&pdev->dev, &dev_attr_lan6_sfp);
+	ret |= device_create_file(&pdev->dev, &dev_attr_lan5_mode);
+	ret |= device_create_file(&pdev->dev, &dev_attr_lan6_mode);
+
+	if (unlikely(ret))
+		dev_err(&pdev->dev, "Failed creating attrs\n");
+
+	/* Add a nice symlink to the real device */
+	ret = sysfs_create_link(kernel_kobj, &pdev->dev.kobj, "gw16083");
+
+	INIT_DELAYED_WORK(&priv->work, mv88e6176_work);
+	priv->workq = create_singlethread_workqueue("gw16083");
+	if (!priv->workq)
+		return -ENODEV;
+	queue_delayed_work(priv->workq, &priv->work, 0);
+
+	dev_dbg(dev, "initial state: GPIO=0x%02x "
+		"Port5_serdes=%d Port6_serdes=%d\n",
+		read_switch_scratch(pdev, MV_GPIO_DATA),
+		(read_switch_port_phy(pdev, 5, MII_M1111_PHY_EXT_SR)
+		 & (1<<13) ? 1:0),
+		(read_switch_port_phy(pdev, 6, MII_M1111_PHY_EXT_SR)
+		 & (1<<13) ? 1:0));
+
+	return ret;
+}
+
+static struct phy_driver mv88e6176_phy_driver = {
+	.name		= "gw16083",
+	.phy_id		= MV_IDENT_VALUE,
+	.phy_id_mask	= MV_IDENT_MASK,
+	.features	= PHY_BASIC_FEATURES,
+	.probe		= &mv88e6176_probe,
+	.remove		= &mv88e6176_remove,
+	.config_init	= &mv88e6176_config_init,
+	.config_aneg	= &mv88e6176_config_aneg,
+	.read_status	= &mv88e6176_read_status,
+	.driver		= { .owner = THIS_MODULE },
+};
+
+/*
+ * I2C driver
+ */
+
+/* See SFF-8472 */
+struct sfp_msa {
+	/* Basic ID fields */
+	u8	identifier;
+	u8	ext_identifier;
+	u8	connector;
+	u8	transceiver[8];
+	u8	encoding;
+	u8	br_nominal;
+	u8	rate_identifier;
+	u8	length_smf_km;
+	u8	length_smf;
+	u8	length_om2;
+	u8	length_om1;
+	u8	length_om4;
+	u8	length_om3;
+	u8	vendor_name[16];
+	u8	transceiver2;
+	u8	vendor_oui[3];
+	u8	vendor_pn[16];
+	u8	vendor_rev[4];
+	u8	wavelength[2];
+	u8	resv1;
+	u8	cc_base;
+
+	/* extended id fields */
+	u8	options[2];
+	u8	br_max;
+	u8	br_min;
+	u8	vendor_sn[16];
+	u8	date_code[8];
+	u8	diags_type;
+	u8	enhanced_options;
+	u8	sff8472_compliance;
+	u8	cc_ext;
+
+	/* Vendor specific ID fields */
+	u8	vendor_data[32];
+	u8	sff8079[128];
+};
+
+enum identifier {
+	UNKNOWN,
+	GBIC,
+	SFF,
+	SFP,
+	XBI,
+	XENPACK,
+	XFP,
+	XFF,
+	XFP_E,
+	XPAK,
+	X2,
+	DWDM_SFP,
+	QSFP,
+	MAX_ID,
+};
+
+const char* id_names[] = {
+	"UNKONWN",
+	"GBIC",
+	"SFF",
+	"SFP",
+	NULL,
+};
+
+/* Flags for SFP modules compatible with ETH up to 1Gb */
+struct sfp_flags {
+	u8 e1000_base_sx:1;
+	u8 e1000_base_lx:1;
+	u8 e1000_base_cx:1;
+	u8 e1000_base_t:1;
+	u8 e100_base_lx:1;
+	u8 e100_base_fx:1;
+	u8 e10_base_bx10:1;
+	u8 e10_base_px:1;
+};
+
+#define STRING_APPEND(str, src)				\
+	strncat(str, src, sizeof(src));			\
+	for (i = 1; i < sizeof(str); i++)		\
+		if (str[i-1] == ' ' && str[i] == ' ')	\
+			str[i] = 0;
+
+static int gw16083_read_port_sfp(struct i2c_client *client,
+				 struct mv88e1111_port_state *state)
+{
+	int ret = 0;
+	u8 data[256];
+	struct sfp_flags *eth_flags;
+	u8 crc;
+	int i;
+	u8 *str;
+	struct sfp_msa *sfp_msa = (struct sfp_msa *)data;
+	int port = state->port;
+	union i2c_smbus_data d;
+
+	dev_dbg(&client->dev, "%s Port%d\n", __func__, port);
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_READ_I2C_BLOCK))
+		return -ENODEV;
+	d.byte = (port == 5) ? 1 : 2;
+	if (i2c_smbus_xfer(client->adapter, GW16083_I2C_ADDR_PCA9543,
+			   client->flags, I2C_SMBUS_WRITE, 0,
+			   I2C_SMBUS_BYTE_DATA, &d) < 0)
+	{
+		dev_err(&client->dev,
+			"Port%d: failed writing PCA9543 register\n", port);
+		return ret;
+	}
+
+	/* read all 256 bytes of SFP EEPROM */
+	for (i = 0; i < sizeof(data); i += I2C_SMBUS_BLOCK_MAX) {
+		d.block[0] = I2C_SMBUS_BLOCK_MAX;
+		if (i2c_smbus_xfer(client->adapter, GW16083_I2C_ADDR_SFP1,
+				   client->flags, I2C_SMBUS_READ, i,
+				   I2C_SMBUS_I2C_BLOCK_DATA, &d) < 0)
+		{
+			dev_err(&client->dev,
+				"Port%d: failed reading SFP data\n", port);
+			return ret;
+		}
+		memcpy(data + i, d.block + 1, I2C_SMBUS_BLOCK_MAX);
+	}
+
+	/* Validate checksums */
+	for (crc = 0, i = 0; i < 63; i++)
+		crc += data[i];
+	if (crc != sfp_msa->cc_base) {
+		dev_err(&client->dev, "Port%d: "
+			"Checksum failure for Base ID fields: 0x%02x\n", port,
+			crc);
+#ifdef FAIL_ON_CHECKSUM_ERR
+		return -EINVAL;
+#endif
+	}
+	for (crc = 0, i = 64; i < 95; i++)
+		crc += data[i];
+	if (crc != sfp_msa->cc_ext) {
+		dev_err(&client->dev, "Port%d: "
+			"Checksum failure for Extended ID fields: 0x%02x\n",
+			port, crc);
+#ifdef FAIL_ON_CHECKSUM_ERR
+		return -EINVAL;
+#endif
+	}
+	state->sfp_id[0] = 0;
+	for (i = 0; id_names[i]; i++) {
+		if (sfp_msa->identifier == i) {
+			sprintf(state->sfp_id, "%s: ", id_names[i]);
+			break;
+		}
+	}
+	STRING_APPEND(state->sfp_id, sfp_msa->vendor_oui);
+	STRING_APPEND(state->sfp_id, sfp_msa->vendor_name);
+	STRING_APPEND(state->sfp_id, sfp_msa->vendor_pn);
+	STRING_APPEND(state->sfp_id, sfp_msa->vendor_rev);
+	STRING_APPEND(state->sfp_id, sfp_msa->vendor_sn);
+	dev_info(&client->dev, "Port%d: %s\n", port, state->sfp_id);
+
+	if ((sfp_msa->identifier != GBIC) &&
+	    (sfp_msa->identifier != SFF) &&
+	    (sfp_msa->identifier != SFP))
+	{
+		dev_err(&client->dev, "Port%d: Unknown module identifier: %d\n",
+			port, sfp_msa->identifier);
+		return -EINVAL;
+	}
+
+	str = "";
+	eth_flags = (struct sfp_flags *)(sfp_msa->transceiver + 3);
+	if (eth_flags->e1000_base_sx) {
+		str = "1000Base-SX (Fiber)";
+	} else if (eth_flags->e1000_base_lx) {
+		str = "1000Base-LX (Fiber)";
+	} else if (eth_flags->e1000_base_t) {
+		str = "1000Base-T (Copper)";
+	} else if (eth_flags->e100_base_fx) {
+		str = "100Base-FX (Fiber) - not supported";
+		ret = -EINVAL;
+	} else {
+		str = "Unknown/Unsupported media type";
+		ret = -EINVAL;
+	}
+	if (ret)
+		dev_err(&client->dev, "Port%d: %s (0x%02x)\n", port, str,
+			sfp_msa->transceiver[3]);
+	else
+		dev_info(&client->dev, "Port%d: %s (0x%02x)\n", port, str,
+			sfp_msa->transceiver[3]);
+
+	return ret;
+}
+
+static int gw16083_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	int ret;
+
+	dev_info(&client->dev, "GW16083 Ethernet Expansion Mezzanine\n");
+	if (gw16083_client) {
+		dev_err(&client->dev, "client already registered\n");
+		return -EINVAL;
+	}
+	gw16083_client = client;
+
+	ret = phy_driver_register(&mv88e6176_phy_driver);
+	if (ret)
+		dev_err(&client->dev,
+			"failed to register mv88e6176 phy driver: %d\n", ret);
+	return ret;
+}
+
+static int gw16083_remove(struct i2c_client *client)
+{
+	dev_dbg(&client->dev, "%s\n", __func__);
+
+	phy_driver_unregister(&mv88e6176_phy_driver);
+	gw16083_client = NULL;
+	return 0;
+}
+
+static const struct of_device_id gw16083_dt_ids[] = {
+	{ .compatible = "gateworks,gw16083", },
+	{ }
+};
+
+MODULE_DEVICE_TABLE(of, gw16083_dt_ids);
+
+static const struct i2c_device_id gw16083_id[] = {
+	{ "gw16083", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, gw16083_id);
+
+static struct i2c_driver gw16083_driver = {
+	.driver = {
+		.name	= "gw16083",
+		.of_match_table = gw16083_dt_ids,
+	},
+	.probe		= gw16083_probe,
+	.remove		= gw16083_remove,
+	.id_table	= gw16083_id,
+};
+
+static int __init mv88e6176_init(void)
+{
+	return i2c_add_driver(&gw16083_driver);
+}
+
+static void __exit mv88e6176_exit(void)
+{
+	i2c_del_driver(&gw16083_driver);
+}
+
+module_init(mv88e6176_init);
+module_exit(mv88e6176_exit);
diff --git a/target/linux/imx6/files-4.3/drivers/net/phy/gw16083.h b/target/linux/imx6/files-4.3/drivers/net/phy/gw16083.h
new file mode 100644
index 0000000..db96f2b
--- /dev/null
+++ b/target/linux/imx6/files-4.3/drivers/net/phy/gw16083.h
@@ -0,0 +1,123 @@
+/*
+ * drivers/net/phy/mv88e6176.h
+ *
+ * Driver for Marvell Switch
+ *
+ * Author: Tim Harvey
+ *
+ * Copyright (c) 2014 Tim Harvey <tharvey at gateworks.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ *
+ */
+
+#ifndef _GW16083_H_
+#define _GW16083_H_
+
+#define MII_MARVELL_PHY_PAGE		22
+
+/*
+ * I2C Addresses
+ */
+#define GW16083_I2C_ADDR_SFP1		0x50
+#define GW16083_I2C_ADDR_SFP2		0x51
+#define GW16083_I2C_ADDR_EEPROM		0x52
+#define GW16083_I2C_ADDR_PCA9543	0x70
+
+/*
+ * MV88E1111 PHY Registers
+ */
+enum {
+	MII_M1111_PHY_CONTROL		= 0,
+	MII_M1111_PHY_STATUS 		= 1,
+	MII_M1111_PHY_IDENT0		= 2,
+	MII_M1111_PHY_IDENT1		= 3,
+	MII_M1111_PHY_EXT_CR		= 20,
+	MII_M1111_PHY_LED_CONTROL	= 24,
+	MII_M1111_PHY_EXT_SR		= 27,
+};
+
+#define MII_M1111_PHY_ID_MASK		0xfffffff0
+#define MII_M1111_PHY_ID		0x01410cc0
+
+#define MII_M1111_PHY_CONTROL_RESET	(1 << 15)
+#define MII_M1111_PHY_LED_DIRECT	0x4100
+#define MII_M1111_PHY_LED_PULSE_STR	0x4111
+#define MII_M1111_PHY_LED_COMBINE	0x411c
+#define MII_M1111_RX_DELAY		0x80
+#define MII_M1111_TX_DELAY		0x2
+
+/*
+ * MV88E6176 Switch Registers
+ */
+
+/* PHY Addrs */
+#define MV_BASE		0x10
+#define MV_GLOBAL1	0x1b
+#define MV_GLOBAL2	0x1c
+#define MV_GLOBAL3	0x1d
+
+/* Global2 Registers */
+enum {
+	MV_SMI_PHY_COMMAND	= 0x18,
+	MV_SMI_PHY_DATA		= 0x19,
+	MV_SCRATCH_MISC		= 0x1A,
+};
+
+/* Scratch And Misc Reg offsets */
+enum {
+	MV_GPIO_MODE		= 0x60,
+	MV_GPIO_DIR		= 0x62,
+	MV_GPIO_DATA		= 0x64,
+	MV_GPIO76_CNTL		= 0x6B,
+	MV_GPIO54_CNTL		= 0x6A,
+	MV_GPIO32_CNTL		= 0x69,
+	MV_GPIO10_CNTL		= 0x68,
+	MV_CONFIG0		= 0x70,
+	MV_CONFIG1		= 0x71,
+	MV_CONFIG2		= 0x72,
+	MV_CONFIG3		= 0x73,
+};
+
+/* PHY Registers */
+enum {
+	MV_PHY_CONTROL      = 0x00,
+	MV_PHY_STATUS       = 0x01,
+	MV_PHY_IDENT0       = 0x02,
+	MV_PHY_IDENT1       = 0x03,
+	MV_PHY_ANEG         = 0x04,
+	MV_PHY_LINK_ABILITY = 0x05,
+	MV_PHY_ANEG_EXPAND  = 0x06,
+	MV_PHY_XMIT_NEXTP   = 0x07,
+	MV_PHY_LINK_NEXTP   = 0x08,
+	MV_PHY_CONTROL1     = 0x10,
+	MV_PHY_STATUS1      = 0x11,
+	MV_PHY_INTR_EN      = 0x12,
+};
+
+/* Port Registers */
+enum {
+	MV_PORT_STATUS      	= 0x00,
+	MV_PORT_PHYS_CONTROL	= 0x01,
+	MV_PORT_IDENT       	= 0x03,
+	MV_PORT_CONTROL     	= 0x04,
+	MV_PORT_VLANMAP     	= 0x06,
+	MV_PORT_ASSOC       	= 0x0b,
+	MV_PORT_RXCOUNT     	= 0x10,
+	MV_PORT_TXCOUNT     	= 0x11,
+};
+
+#define SMIBUSY		(1<<15)
+#define SMIMODE22	(1<<12)
+#define SMIOP_READ	(2<<10)
+#define SMIOP_WRITE	(1<<10)
+#define DEVADDR		5
+#define REGADDR		0
+
+#define MV_IDENT_MASK		0x0000fff0
+#define MV_IDENT_VALUE		0x00001760
+
+#endif /* _GW16083_H_ */
diff --git a/target/linux/imx6/patches-4.3/035-ARM-dts-imx-ventana-set-GW54xx-PMIC-swbst-regulator-.patch b/target/linux/imx6/patches-4.3/035-ARM-dts-imx-ventana-set-GW54xx-PMIC-swbst-regulator-.patch
new file mode 100644
index 0000000..a92e0f8
--- /dev/null
+++ b/target/linux/imx6/patches-4.3/035-ARM-dts-imx-ventana-set-GW54xx-PMIC-swbst-regulator-.patch
@@ -0,0 +1,28 @@
+From 57b82d9e79d77442bae3d2c13b98ceccb39fe5e2 Mon Sep 17 00:00:00 2001
+From: Tim Harvey <tharvey at gateworks.com>
+Date: Thu, 5 Nov 2015 10:49:31 -0800
+Subject: [PATCH 1/3] ARM: dts: imx: ventana: set GW54xx PMIC swbst regulator
+ as always-on
+
+The GW54xx PMIC swbst regulator is used for LVDS power, CANbus xceiver
+and HDMI DDC and is enabled by the bootloader. Set the regulator to
+always-on so that Linux doesn't turn it off thinking its not needed.
+
+Signed-off-by: Tim Harvey <tharvey at gateworks.com>
+---
+ arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 2 ++
+ 1 file changed, 2 insertions(+)
+
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi	2015-11-01 16:05:25.000000000 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi	2015-12-18 10:43:37.000000000 -0800
+@@ -260,6 +260,8 @@
+ 			swbst_reg: swbst {
+ 				regulator-min-microvolt = <5000000>;
+ 				regulator-max-microvolt = <5150000>;
++				regulator-boot-on;
++				regulator-always-on;
+ 			};
+ 
+ 			snvs_reg: vsnvs {
diff --git a/target/linux/imx6/patches-4.3/036-ARM-dts-imx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch b/target/linux/imx6/patches-4.3/036-ARM-dts-imx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch
new file mode 100644
index 0000000..2768b09
--- /dev/null
+++ b/target/linux/imx6/patches-4.3/036-ARM-dts-imx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch
@@ -0,0 +1,37 @@
+From 473d0353979db3673a7aa365265ba9b00decd414 Mon Sep 17 00:00:00 2001
+From: Tim Harvey <tharvey at gateworks.com>
+Date: Thu, 5 Nov 2015 10:52:53 -0800
+Subject: [PATCH 2/3] ARM: dts: imx: ventana: fix GW53xx/GW54xx lvds channel
+
+Signed-off-by: Tim Harvey <tharvey at gateworks.com>
+---
+ arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 2 +-
+ arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 2 +-
+ 2 files changed, 2 insertions(+), 2 deletions(-)
+
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi	2015-11-01 16:05:25.000000000 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi	2015-12-18 10:43:32.000000000 -0800
+@@ -247,7 +247,7 @@
+ &ldb {
+ 	status = "okay";
+ 
+-	lvds-channel at 1 {
++	lvds-channel at 0 {
+ 		fsl,data-mapping = "spwg";
+ 		fsl,data-width = <18>;
+ 		status = "okay";
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi	2015-12-18 10:39:44.855158318 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi	2015-12-18 10:43:32.000000000 -0800
+@@ -338,7 +338,7 @@
+ &ldb {
+ 	status = "okay";
+ 
+-	lvds-channel at 1 {
++	lvds-channel at 0 {
+ 		fsl,data-mapping = "spwg";
+ 		fsl,data-width = <18>;
+ 		status = "okay";
diff --git a/target/linux/imx6/patches-4.3/037-ARM-dts-imx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch b/target/linux/imx6/patches-4.3/037-ARM-dts-imx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch
new file mode 100644
index 0000000..768648e
--- /dev/null
+++ b/target/linux/imx6/patches-4.3/037-ARM-dts-imx-ventana-fix-GW53xx-GW54xx-lvds-channel.patch
@@ -0,0 +1,76 @@
+From d86b202436b6f3111c4c37b8701daa0764d2ca55 Mon Sep 17 00:00:00 2001
+From: Tim Harvey <tharvey at gateworks.com>
+Date: Thu, 5 Nov 2015 11:10:00 -0800
+Subject: [PATCH 3/3] ARM: dts: imx: ventana: Allow HDMI and LVDS to work
+ simultaneously
+
+Currently it is not possible to have HDMI and LVDS working simultaneously,
+because both ports try to use PLL5.
+
+Move the LVDS clock parent to PLL3_USB_OTG, so that HDMI and LVDS can be
+driven from independent sources.
+
+With this change the LDB pixel clock goes to 68.57 MHz, which is still
+within the valid range for the displays supported by the Ventana boards.
+
+Signed-off-by: Tim Harvey <tharvey at gateworks.com>
+---
+ arch/arm/boot/dts/imx6qdl-gw52xx.dtsi | 7 +++++++
+ arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 7 +++++++
+ arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 7 +++++++
+ 3 files changed, 21 insertions(+)
+
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi	2015-11-01 16:05:25.000000000 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi	2015-12-18 10:43:32.000000000 -0800
+@@ -151,6 +151,13 @@
+ 	status = "okay";
+ };
+ 
++&clks {
++	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
++	                  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
++	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
++	                  <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
++};
++
+ &fec {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&pinctrl_enet>;
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi	2015-12-18 10:39:44.867158318 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi	2015-12-18 10:43:32.000000000 -0800
+@@ -152,6 +152,13 @@
+ 	status = "okay";
+ };
+ 
++&clks {
++	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
++	                  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
++	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
++	                  <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
++};
++
+ &fec {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&pinctrl_enet>;
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi	2015-12-18 10:39:44.871158318 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi	2015-12-18 10:43:32.000000000 -0800
+@@ -142,6 +142,13 @@
+ 	status = "okay";
+ };
+ 
++&clks {
++	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
++	                  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
++	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
++	                  <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
++};
++
+ &fec {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&pinctrl_enet>;
diff --git a/target/linux/imx6/patches-4.3/100-bootargs.patch b/target/linux/imx6/patches-4.3/100-bootargs.patch
new file mode 100644
index 0000000..3c22ec7
--- /dev/null
+++ b/target/linux/imx6/patches-4.3/100-bootargs.patch
@@ -0,0 +1,13 @@
+Index: linux-4.3/arch/arm/boot/dts/imx6dl-wandboard.dts
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6dl-wandboard.dts	2015-11-01 16:05:25.000000000 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6dl-wandboard.dts	2015-12-18 10:39:44.923158318 -0800
+@@ -19,4 +19,8 @@
+ 	memory {
+ 		reg = <0x10000000 0x40000000>;
+ 	};
++
++	chosen {
++		bootargs = "console=ttymxc0,115200";
++	};
+ };
diff --git a/target/linux/imx6/patches-4.3/202-net-igb-add-i210-i211-support-for-phy-read-write.patch b/target/linux/imx6/patches-4.3/202-net-igb-add-i210-i211-support-for-phy-read-write.patch
new file mode 100644
index 0000000..6a636a3
--- /dev/null
+++ b/target/linux/imx6/patches-4.3/202-net-igb-add-i210-i211-support-for-phy-read-write.patch
@@ -0,0 +1,131 @@
+Author: Tim Harvey <tharvey at gateworks.com>
+Date:   Thu May 15 00:12:26 2014 -0700
+
+    net: igb: add i210/i211 support for phy read/write
+    
+    The i210/i211 uses the MDICNFG register for the phy address instead of the
+    MDIC register.
+    
+    Signed-off-by: Tim Harvey <tharvey at gateworks.com>
+
+Index: linux-4.3/drivers/net/ethernet/intel/igb/e1000_phy.c
+===================================================================
+--- linux-4.3.orig/drivers/net/ethernet/intel/igb/e1000_phy.c	2015-11-01 16:05:25.000000000 -0800
++++ linux-4.3/drivers/net/ethernet/intel/igb/e1000_phy.c	2015-12-18 10:43:28.000000000 -0800
+@@ -129,7 +129,7 @@
+ s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
+ {
+ 	struct e1000_phy_info *phy = &hw->phy;
+-	u32 i, mdic = 0;
++	u32 i, mdicnfg, mdic = 0;
+ 	s32 ret_val = 0;
+ 
+ 	if (offset > MAX_PHY_REG_ADDRESS) {
+@@ -142,11 +142,25 @@
+ 	 * Control register.  The MAC will take care of interfacing with the
+ 	 * PHY to retrieve the desired data.
+ 	 */
+-	mdic = ((offset << E1000_MDIC_REG_SHIFT) |
+-		(phy->addr << E1000_MDIC_PHY_SHIFT) |
+-		(E1000_MDIC_OP_READ));
++	switch (hw->mac.type) {
++	case e1000_i210:
++	case e1000_i211:
++		mdicnfg = rd32(E1000_MDICNFG);
++		mdicnfg &= ~(E1000_MDICNFG_PHY_MASK);
++		mdicnfg |= (phy->addr << E1000_MDICNFG_PHY_SHIFT);
++		wr32(E1000_MDICNFG, mdicnfg);
++		mdic = ((offset << E1000_MDIC_REG_SHIFT) |
++			(E1000_MDIC_OP_READ));
++		break;
++	default:
++		mdic = ((offset << E1000_MDIC_REG_SHIFT) |
++			(phy->addr << E1000_MDIC_PHY_SHIFT) |
++			(E1000_MDIC_OP_READ));
++		break;
++	}
+ 
+ 	wr32(E1000_MDIC, mdic);
++	wrfl();
+ 
+ 	/* Poll the ready bit to see if the MDI read completed
+ 	 * Increasing the time out as testing showed failures with
+@@ -171,6 +185,18 @@
+ 	*data = (u16) mdic;
+ 
+ out:
++	switch (hw->mac.type) {
++		/* restore MDICNFG to have phy's addr */
++		case e1000_i210:
++		case e1000_i211:
++			mdicnfg = rd32(E1000_MDICNFG);
++			mdicnfg &= ~(E1000_MDICNFG_PHY_MASK);
++			mdicnfg |= (hw->phy.addr << E1000_MDICNFG_PHY_SHIFT);
++			wr32(E1000_MDICNFG, mdicnfg);
++			break;
++		default:
++			break;
++	}
+ 	return ret_val;
+ }
+ 
+@@ -185,7 +211,7 @@
+ s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data)
+ {
+ 	struct e1000_phy_info *phy = &hw->phy;
+-	u32 i, mdic = 0;
++	u32 i, mdicnfg, mdic = 0;
+ 	s32 ret_val = 0;
+ 
+ 	if (offset > MAX_PHY_REG_ADDRESS) {
+@@ -198,12 +224,27 @@
+ 	 * Control register.  The MAC will take care of interfacing with the
+ 	 * PHY to retrieve the desired data.
+ 	 */
+-	mdic = (((u32)data) |
+-		(offset << E1000_MDIC_REG_SHIFT) |
+-		(phy->addr << E1000_MDIC_PHY_SHIFT) |
+-		(E1000_MDIC_OP_WRITE));
++	switch (hw->mac.type) {
++		case e1000_i210:
++		case e1000_i211:
++			mdicnfg = rd32(E1000_MDICNFG);
++			mdicnfg &= ~(E1000_MDICNFG_PHY_MASK);
++			mdicnfg |= (phy->addr << E1000_MDICNFG_PHY_SHIFT);
++			wr32(E1000_MDICNFG, mdicnfg);
++			mdic = (((u32)data) |
++				(offset << E1000_MDIC_REG_SHIFT) |
++				(E1000_MDIC_OP_WRITE));
++			break;
++		default:
++			mdic = (((u32)data) |
++				(offset << E1000_MDIC_REG_SHIFT) |
++				(phy->addr << E1000_MDIC_PHY_SHIFT) |
++				(E1000_MDIC_OP_WRITE));
++			break;
++	}
+ 
+ 	wr32(E1000_MDIC, mdic);
++	wrfl();
+ 
+ 	/* Poll the ready bit to see if the MDI read completed
+ 	 * Increasing the time out as testing showed failures with
+@@ -227,6 +268,18 @@
+ 	}
+ 
+ out:
++	switch (hw->mac.type) {
++		/* restore MDICNFG to have phy's addr */
++		case e1000_i210:
++		case e1000_i211:
++			mdicnfg = rd32(E1000_MDICNFG);
++			mdicnfg &= ~(E1000_MDICNFG_PHY_MASK);
++			mdicnfg |= (hw->phy.addr << E1000_MDICNFG_PHY_SHIFT);
++			wr32(E1000_MDICNFG, mdicnfg);
++			break;
++		default:
++			break;
++	}
+ 	return ret_val;
+ }
+ 
diff --git a/target/linux/imx6/patches-4.3/203-net-igb-add-phy-read-write-functions-that-accept-phy.patch b/target/linux/imx6/patches-4.3/203-net-igb-add-phy-read-write-functions-that-accept-phy.patch
new file mode 100644
index 0000000..4bb691d
--- /dev/null
+++ b/target/linux/imx6/patches-4.3/203-net-igb-add-phy-read-write-functions-that-accept-phy.patch
@@ -0,0 +1,266 @@
+From 16df7dc5901c1cb2a40f6adbd0d9423768ed8210 Mon Sep 17 00:00:00 2001
+From: Tim Harvey <tharvey at gateworks.com>
+Date: Thu, 15 May 2014 00:29:18 -0700
+Subject: [PATCH] net: igb: add phy read/write functions that accept phy addr
+
+Add igb_write_reg_gs40g/igb_read_reg_gs40g that can be passed a phy address.
+The existing igb_write_phy_reg_gs40g/igb_read_phy_reg_gs40g become wrappers
+to this function.
+
+Signed-off-by: Tim Harvey <tharvey at gateworks.com>
+---
+ drivers/net/ethernet/intel/igb/e1000_82575.c |  4 +-
+ drivers/net/ethernet/intel/igb/e1000_phy.c   | 74 +++++++++++++++++++---------
+ drivers/net/ethernet/intel/igb/e1000_phy.h   |  6 ++-
+ 3 files changed, 58 insertions(+), 26 deletions(-)
+
+Index: linux-4.3/drivers/net/ethernet/intel/igb/e1000_82575.c
+===================================================================
+--- linux-4.3.orig/drivers/net/ethernet/intel/igb/e1000_82575.c	2015-11-01 16:05:25.000000000 -0800
++++ linux-4.3/drivers/net/ethernet/intel/igb/e1000_82575.c	2015-12-18 10:43:28.000000000 -0800
+@@ -2153,7 +2153,7 @@
+ 	if (ret_val)
+ 		goto out;
+ 
+-	ret_val = igb_read_phy_reg_mdic(hw, offset, data);
++	ret_val = igb_read_phy_reg_mdic(hw, hw->phy.addr, offset, data);
+ 
+ 	hw->phy.ops.release(hw);
+ 
+@@ -2178,7 +2178,7 @@
+ 	if (ret_val)
+ 		goto out;
+ 
+-	ret_val = igb_write_phy_reg_mdic(hw, offset, data);
++	ret_val = igb_write_phy_reg_mdic(hw, hw->phy.addr, offset, data);
+ 
+ 	hw->phy.ops.release(hw);
+ 
+Index: linux-4.3/drivers/net/ethernet/intel/igb/e1000_phy.c
+===================================================================
+--- linux-4.3.orig/drivers/net/ethernet/intel/igb/e1000_phy.c	2015-12-18 10:39:44.931158318 -0800
++++ linux-4.3/drivers/net/ethernet/intel/igb/e1000_phy.c	2015-12-18 10:39:44.939158318 -0800
+@@ -126,9 +126,8 @@
+  *  Reads the MDI control regsiter in the PHY at offset and stores the
+  *  information read to data.
+  **/
+-s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
++s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u8 addr, u32 offset, u16 *data)
+ {
+-	struct e1000_phy_info *phy = &hw->phy;
+ 	u32 i, mdicnfg, mdic = 0;
+ 	s32 ret_val = 0;
+ 
+@@ -147,14 +146,14 @@
+ 	case e1000_i211:
+ 		mdicnfg = rd32(E1000_MDICNFG);
+ 		mdicnfg &= ~(E1000_MDICNFG_PHY_MASK);
+-		mdicnfg |= (phy->addr << E1000_MDICNFG_PHY_SHIFT);
++		mdicnfg |= (addr << E1000_MDICNFG_PHY_SHIFT);
+ 		wr32(E1000_MDICNFG, mdicnfg);
+ 		mdic = ((offset << E1000_MDIC_REG_SHIFT) |
+ 			(E1000_MDIC_OP_READ));
+ 		break;
+ 	default:
+ 		mdic = ((offset << E1000_MDIC_REG_SHIFT) |
+-			(phy->addr << E1000_MDIC_PHY_SHIFT) |
++			(addr << E1000_MDIC_PHY_SHIFT) |
+ 			(E1000_MDIC_OP_READ));
+ 		break;
+ 	}
+@@ -208,9 +207,8 @@
+  *
+  *  Writes data to MDI control register in the PHY at offset.
+  **/
+-s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data)
++s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u8 addr, u32 offset, u16 data)
+ {
+-	struct e1000_phy_info *phy = &hw->phy;
+ 	u32 i, mdicnfg, mdic = 0;
+ 	s32 ret_val = 0;
+ 
+@@ -229,7 +227,7 @@
+ 		case e1000_i211:
+ 			mdicnfg = rd32(E1000_MDICNFG);
+ 			mdicnfg &= ~(E1000_MDICNFG_PHY_MASK);
+-			mdicnfg |= (phy->addr << E1000_MDICNFG_PHY_SHIFT);
++			mdicnfg |= (addr << E1000_MDICNFG_PHY_SHIFT);
+ 			wr32(E1000_MDICNFG, mdicnfg);
+ 			mdic = (((u32)data) |
+ 				(offset << E1000_MDIC_REG_SHIFT) |
+@@ -238,7 +236,7 @@
+ 		default:
+ 			mdic = (((u32)data) |
+ 				(offset << E1000_MDIC_REG_SHIFT) |
+-				(phy->addr << E1000_MDIC_PHY_SHIFT) |
++				(addr << E1000_MDIC_PHY_SHIFT) |
+ 				(E1000_MDIC_OP_WRITE));
+ 			break;
+ 	}
+@@ -458,7 +456,7 @@
+ 		goto out;
+ 
+ 	if (offset > MAX_PHY_MULTI_PAGE_REG) {
+-		ret_val = igb_write_phy_reg_mdic(hw,
++		ret_val = igb_write_phy_reg_mdic(hw, hw->phy.addr,
+ 						 IGP01E1000_PHY_PAGE_SELECT,
+ 						 (u16)offset);
+ 		if (ret_val) {
+@@ -467,8 +465,8 @@
+ 		}
+ 	}
+ 
+-	ret_val = igb_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+-					data);
++	ret_val = igb_read_phy_reg_mdic(hw, hw->phy.addr,
++					MAX_PHY_REG_ADDRESS & offset, data);
+ 
+ 	hw->phy.ops.release(hw);
+ 
+@@ -497,7 +495,7 @@
+ 		goto out;
+ 
+ 	if (offset > MAX_PHY_MULTI_PAGE_REG) {
+-		ret_val = igb_write_phy_reg_mdic(hw,
++		ret_val = igb_write_phy_reg_mdic(hw, hw->phy.addr,
+ 						 IGP01E1000_PHY_PAGE_SELECT,
+ 						 (u16)offset);
+ 		if (ret_val) {
+@@ -506,8 +504,8 @@
+ 		}
+ 	}
+ 
+-	ret_val = igb_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+-					 data);
++	ret_val = igb_write_phy_reg_mdic(hw, hw->phy.addr,
++					 MAX_PHY_REG_ADDRESS & offset, data);
+ 
+ 	hw->phy.ops.release(hw);
+ 
+@@ -2547,8 +2545,9 @@
+ }
+ 
+ /**
+- *  igb_write_phy_reg_gs40g - Write GS40G PHY register
++ *  igb_write_reg_gs40g - Write GS40G PHY register
+  *  @hw: pointer to the HW structure
++ *  @addr: phy address to write to
+  *  @offset: lower half is register offset to write to
+  *     upper half is page to use.
+  *  @data: data to write at register offset
+@@ -2556,7 +2555,7 @@
+  *  Acquires semaphore, if necessary, then writes the data to PHY register
+  *  at the offset.  Release any acquired semaphores before exiting.
+  **/
+-s32 igb_write_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 data)
++s32 igb_write_reg_gs40g(struct e1000_hw *hw, u8 addr, u32 offset, u16 data)
+ {
+ 	s32 ret_val;
+ 	u16 page = offset >> GS40G_PAGE_SHIFT;
+@@ -2566,10 +2565,10 @@
+ 	if (ret_val)
+ 		return ret_val;
+ 
+-	ret_val = igb_write_phy_reg_mdic(hw, GS40G_PAGE_SELECT, page);
++	ret_val = igb_write_phy_reg_mdic(hw, addr, GS40G_PAGE_SELECT, page);
+ 	if (ret_val)
+ 		goto release;
+-	ret_val = igb_write_phy_reg_mdic(hw, offset, data);
++	ret_val = igb_write_phy_reg_mdic(hw, addr, offset, data);
+ 
+ release:
+ 	hw->phy.ops.release(hw);
+@@ -2577,8 +2576,24 @@
+ }
+ 
+ /**
+- *  igb_read_phy_reg_gs40g - Read GS40G  PHY register
++ *  igb_write_phy_reg_gs40g - Write GS40G PHY register
++ *  @hw: pointer to the HW structure
++ *  @offset: lower half is register offset to write to
++ *     upper half is page to use.
++ *  @data: data to write at register offset
++ *
++ *  Acquires semaphore, if necessary, then writes the data to PHY register
++ *  at the offset.  Release any acquired semaphores before exiting.
++ **/
++s32 igb_write_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 data)
++{
++	return igb_write_reg_gs40g(hw, hw->phy.addr, offset, data);
++}
++
++/**
++ *  igb_read_reg_gs40g - Read GS40G  PHY register
+  *  @hw: pointer to the HW structure
++ *  @addr: phy address to read from
+  *  @offset: lower half is register offset to read to
+  *     upper half is page to use.
+  *  @data: data to read at register offset
+@@ -2586,7 +2601,7 @@
+  *  Acquires semaphore, if necessary, then reads the data in the PHY register
+  *  at the offset.  Release any acquired semaphores before exiting.
+  **/
+-s32 igb_read_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 *data)
++s32 igb_read_reg_gs40g(struct e1000_hw *hw, u8 addr, u32 offset, u16 *data)
+ {
+ 	s32 ret_val;
+ 	u16 page = offset >> GS40G_PAGE_SHIFT;
+@@ -2596,10 +2611,10 @@
+ 	if (ret_val)
+ 		return ret_val;
+ 
+-	ret_val = igb_write_phy_reg_mdic(hw, GS40G_PAGE_SELECT, page);
++	ret_val = igb_write_phy_reg_mdic(hw, addr, GS40G_PAGE_SELECT, page);
+ 	if (ret_val)
+ 		goto release;
+-	ret_val = igb_read_phy_reg_mdic(hw, offset, data);
++	ret_val = igb_read_phy_reg_mdic(hw, addr, offset, data);
+ 
+ release:
+ 	hw->phy.ops.release(hw);
+@@ -2607,6 +2622,21 @@
+ }
+ 
+ /**
++ *  igb_read_phy_reg_gs40g - Read GS40G  PHY register
++ *  @hw: pointer to the HW structure
++ *  @offset: lower half is register offset to read to
++ *     upper half is page to use.
++ *  @data: data to read at register offset
++ *
++ *  Acquires semaphore, if necessary, then reads the data in the PHY register
++ *  at the offset.  Release any acquired semaphores before exiting.
++ **/
++s32 igb_read_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 *data)
++{
++	return igb_read_reg_gs40g(hw, hw->phy.addr, offset, data);
++}
++
++/**
+  *  igb_set_master_slave_mode - Setup PHY for Master/slave mode
+  *  @hw: pointer to the HW structure
+  *
+Index: linux-4.3/drivers/net/ethernet/intel/igb/e1000_phy.h
+===================================================================
+--- linux-4.3.orig/drivers/net/ethernet/intel/igb/e1000_phy.h	2015-11-01 16:05:25.000000000 -0800
++++ linux-4.3/drivers/net/ethernet/intel/igb/e1000_phy.h	2015-12-18 10:39:44.939158318 -0800
+@@ -62,8 +62,8 @@
+ void igb_power_down_phy_copper(struct e1000_hw *hw);
+ s32  igb_phy_init_script_igp3(struct e1000_hw *hw);
+ s32  igb_initialize_M88E1512_phy(struct e1000_hw *hw);
+-s32  igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
+-s32  igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
++s32  igb_read_phy_reg_mdic(struct e1000_hw *hw, u8 addr, u32 offset, u16 *data);
++s32  igb_write_phy_reg_mdic(struct e1000_hw *hw, u8 addr, u32 offset, u16 data);
+ s32  igb_read_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 *data);
+ s32  igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data);
+ s32  igb_read_sfp_data_byte(struct e1000_hw *hw, u16 offset, u8 *data);
+@@ -73,6 +73,8 @@
+ s32  igb_get_cable_length_82580(struct e1000_hw *hw);
+ s32  igb_read_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 *data);
+ s32  igb_write_phy_reg_gs40g(struct e1000_hw *hw, u32 offset, u16 data);
++s32  igb_read_reg_gs40g(struct e1000_hw *hw, u8 addr, u32 offset, u16 *data);
++s32  igb_write_reg_gs40g(struct e1000_hw *hw, u8 addr, u32 offset, u16 data);
+ s32  igb_check_polarity_m88(struct e1000_hw *hw);
+ 
+ /* IGP01E1000 Specific Registers */
diff --git a/target/linux/imx6/patches-4.3/204-net-igb-register-mii_bus-for-SerDes-w-external-phy.patch b/target/linux/imx6/patches-4.3/204-net-igb-register-mii_bus-for-SerDes-w-external-phy.patch
new file mode 100644
index 0000000..4bee4ac
--- /dev/null
+++ b/target/linux/imx6/patches-4.3/204-net-igb-register-mii_bus-for-SerDes-w-external-phy.patch
@@ -0,0 +1,314 @@
+From 03855caf93f7332a3f320228ba1a0e7baae8a749 Mon Sep 17 00:00:00 2001
+From: Tim Harvey <tharvey at gateworks.com>
+Date: Thu, 15 May 2014 12:36:23 -0700
+Subject: [PATCH] net: igb: register mii_bus for SerDes w/ external phy
+
+If an i210 is configured for 1000BASE-BX link_mode and has an external phy
+specified, then register an mii bus using the external phy address as
+a mask.
+
+An i210 hooked to an external standard phy will be configured with a link_mo
+of SGMII in which case phy ops will be configured and used internall in the
+igb driver for link status. However, in certain cases one might be using a
+backplane SerDes connection to something that talks on the mdio bus but is
+not a standard phy, such as a switch. In this case by registering an mdio
+bus a phy driver can manage the device.
+
+Signed-off-by: Tim Harvey <tharvey at gateworks.com>
+---
+ drivers/net/ethernet/intel/igb/e1000_82575.c |  15 +++
+ drivers/net/ethernet/intel/igb/e1000_hw.h    |   7 ++
+ drivers/net/ethernet/intel/igb/igb_main.c    | 168 ++++++++++++++++++++++++++-
+ 3 files changed, 185 insertions(+), 5 deletions(-)
+
+Index: linux-4.3/drivers/net/ethernet/intel/igb/e1000_82575.c
+===================================================================
+--- linux-4.3.orig/drivers/net/ethernet/intel/igb/e1000_82575.c	2015-12-18 10:39:44.935158318 -0800
++++ linux-4.3/drivers/net/ethernet/intel/igb/e1000_82575.c	2015-12-18 10:39:44.943158318 -0800
+@@ -612,13 +612,25 @@
+ 	switch (link_mode) {
+ 	case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
+ 		hw->phy.media_type = e1000_media_type_internal_serdes;
++		if (igb_sgmii_uses_mdio_82575(hw)) {
++			u32 mdicnfg = rd32(E1000_MDICNFG);
++			mdicnfg &= E1000_MDICNFG_PHY_MASK;
++			hw->phy.addr = mdicnfg >> E1000_MDICNFG_PHY_SHIFT;
++			hw_dbg("1000BASE_KX w/ external MDIO device at 0x%x\n",
++			       hw->phy.addr);
++		} else {
++			hw_dbg("1000BASE_KX");
++		}
+ 		break;
+ 	case E1000_CTRL_EXT_LINK_MODE_SGMII:
+ 		/* Get phy control interface type set (MDIO vs. I2C)*/
+ 		if (igb_sgmii_uses_mdio_82575(hw)) {
+ 			hw->phy.media_type = e1000_media_type_copper;
+ 			dev_spec->sgmii_active = true;
++			hw_dbg("SGMII with external MDIO PHY");
+ 			break;
++		} else {
++			hw_dbg("SGMII with external I2C PHY");
+ 		}
+ 		/* fall through for I2C based SGMII */
+ 	case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
+@@ -635,8 +647,11 @@
+ 				hw->phy.media_type = e1000_media_type_copper;
+ 				dev_spec->sgmii_active = true;
+ 			}
++			hw_dbg("SERDES with external SFP");
+ 
+ 			break;
++		} else {
++			hw_dbg("SERDES");
+ 		}
+ 
+ 		/* do not change link mode for 100BaseFX */
+Index: linux-4.3/drivers/net/ethernet/intel/igb/e1000_hw.h
+===================================================================
+--- linux-4.3.orig/drivers/net/ethernet/intel/igb/e1000_hw.h	2015-11-01 16:05:25.000000000 -0800
++++ linux-4.3/drivers/net/ethernet/intel/igb/e1000_hw.h	2015-12-18 10:39:44.943158318 -0800
+@@ -27,6 +27,7 @@
+ #include <linux/delay.h>
+ #include <linux/io.h>
+ #include <linux/netdevice.h>
++#include <linux/phy.h>
+ 
+ #include "e1000_regs.h"
+ #include "e1000_defines.h"
+@@ -543,6 +544,12 @@
+ 	struct e1000_mbx_info mbx;
+ 	struct e1000_host_mng_dhcp_cookie mng_cookie;
+ 
++#ifdef CONFIG_PHYLIB
++	/* Phylib and MDIO interface */
++	struct mii_bus *mii_bus;
++	struct phy_device *phy_dev;
++	phy_interface_t phy_interface;
++#endif
+ 	union {
+ 		struct e1000_dev_spec_82575	_82575;
+ 	} dev_spec;
+Index: linux-4.3/drivers/net/ethernet/intel/igb/igb_main.c
+===================================================================
+--- linux-4.3.orig/drivers/net/ethernet/intel/igb/igb_main.c	2015-12-18 10:39:44.407158315 -0800
++++ linux-4.3/drivers/net/ethernet/intel/igb/igb_main.c	2015-12-18 10:39:44.943158318 -0800
+@@ -41,6 +41,7 @@
+ #include <linux/if_vlan.h>
+ #include <linux/pci.h>
+ #include <linux/pci-aspm.h>
++#include <linux/phy.h>
+ #include <linux/delay.h>
+ #include <linux/interrupt.h>
+ #include <linux/ip.h>
+@@ -2223,6 +2224,126 @@
+ 	return status;
+ }
+ 
++
++#ifdef CONFIG_PHYLIB
++/*
++ * MMIO/PHYdev support
++ */
++
++static int igb_enet_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
++{
++	struct e1000_hw *hw = bus->priv;
++	u16 out;
++	int err;
++
++	err = igb_read_reg_gs40g(hw, mii_id, regnum, &out);
++	if (err)
++		return err;
++	return out;
++}
++
++static int igb_enet_mdio_write(struct mii_bus *bus, int mii_id, int regnum,
++                               u16 val)
++{
++	struct e1000_hw *hw = bus->priv;
++
++	return igb_write_reg_gs40g(hw, mii_id, regnum, val);
++}
++
++static int igb_enet_mdio_reset(struct mii_bus *bus)
++{
++	udelay(300);
++	return 0;
++}
++
++static void igb_enet_mii_link(struct net_device *netdev)
++{
++}
++
++/* Probe the mdio bus for phys and connect them */
++static int igb_enet_mii_probe(struct net_device *netdev)
++{
++	struct igb_adapter *adapter = netdev_priv(netdev);
++	struct e1000_hw *hw = &adapter->hw;
++	struct phy_device *phy_dev = NULL;
++	int phy_id;
++
++	/* check for attached phy */
++	for (phy_id = 0; (phy_id < PHY_MAX_ADDR); phy_id++) {
++		if (hw->mii_bus->phy_map[phy_id]) {
++			phy_dev = hw->mii_bus->phy_map[phy_id];
++			break;
++		}
++	}
++	if (!phy_dev) {
++		netdev_err(netdev, "no PHY found\n");
++		return -ENODEV;
++	}
++
++	hw->phy_interface = PHY_INTERFACE_MODE_RGMII;
++	phy_dev = phy_connect(netdev, dev_name(&phy_dev->dev),
++			      igb_enet_mii_link, hw->phy_interface);
++	if (IS_ERR(phy_dev)) {
++		netdev_err(netdev, "could not attach to PHY\n");
++		return PTR_ERR(phy_dev);
++	}
++
++	hw->phy_dev = phy_dev;
++	netdev_info(netdev, "igb PHY driver [%s] (mii_bus:phy_addr=%s)\n",
++		hw->phy_dev->drv->name, dev_name(&hw->phy_dev->dev));
++
++	return 0;
++}
++
++/* Create and register mdio bus */
++static int igb_enet_mii_init(struct pci_dev *pdev)
++{
++	struct mii_bus *mii_bus;
++	struct net_device *netdev = pci_get_drvdata(pdev);
++	struct igb_adapter *adapter = netdev_priv(netdev);
++	struct e1000_hw *hw = &adapter->hw;
++	int err;
++
++	mii_bus = mdiobus_alloc();
++	if (mii_bus == NULL) {
++		err = -ENOMEM;
++		goto err_out;
++	}
++
++	mii_bus->name = "igb_enet_mii_bus";
++	mii_bus->read = igb_enet_mdio_read;
++	mii_bus->write = igb_enet_mdio_write;
++	mii_bus->reset = igb_enet_mdio_reset;
++	snprintf(mii_bus->id, MII_BUS_ID_SIZE, "%s-%x",
++		 pci_name(pdev), hw->device_id + 1);
++	mii_bus->priv = hw;
++	mii_bus->parent = &pdev->dev;
++	mii_bus->phy_mask = ~(1 << hw->phy.addr);
++
++	err = mdiobus_register(mii_bus);
++	if (err) {
++		printk(KERN_ERR "failed to register mii_bus: %d\n", err);
++		goto err_out_free_mdiobus;
++	}
++	hw->mii_bus = mii_bus;
++
++	return 0;
++
++err_out_free_mdiobus:
++	mdiobus_free(mii_bus);
++err_out:
++	return err;
++}
++
++static void igb_enet_mii_remove(struct e1000_hw *hw)
++{
++	if (hw->mii_bus) {
++		mdiobus_unregister(hw->mii_bus);
++		mdiobus_free(hw->mii_bus);
++	}
++}
++#endif /* CONFIG_PHYLIB */
++
+ /**
+  *  igb_probe - Device Initialization Routine
+  *  @pdev: PCI device information struct
+@@ -2645,6 +2766,13 @@
+ 		}
+ 	}
+ 	pm_runtime_put_noidle(&pdev->dev);
++
++#ifdef CONFIG_PHYLIB
++	/* create and register the mdio bus if using ext phy */
++	if (rd32(E1000_MDICNFG) & E1000_MDICNFG_EXT_MDIO)
++		igb_enet_mii_init(pdev);
++#endif
++
+ 	return 0;
+ 
+ err_register:
+@@ -2792,6 +2920,10 @@
+ 	struct e1000_hw *hw = &adapter->hw;
+ 
+ 	pm_runtime_get_noresume(&pdev->dev);
++#ifdef CONFIG_PHYLIB
++	if (rd32(E1000_MDICNFG) & E1000_MDICNFG_EXT_MDIO)
++		igb_enet_mii_remove(hw);
++#endif
+ #ifdef CONFIG_IGB_HWMON
+ 	igb_sysfs_exit(adapter);
+ #endif
+@@ -3105,6 +3237,12 @@
+ 	if (!resuming)
+ 		pm_runtime_put(&pdev->dev);
+ 
++#ifdef CONFIG_PHYLIB
++	/* Probe and connect to PHY if using ext phy */
++	if (rd32(E1000_MDICNFG) & E1000_MDICNFG_EXT_MDIO)
++		igb_enet_mii_probe(netdev);
++#endif
++
+ 	/* start the watchdog. */
+ 	hw->mac.get_link_status = 1;
+ 	schedule_work(&adapter->watchdog_task);
+@@ -7090,21 +7228,41 @@
+ static int igb_mii_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
+ {
+ 	struct igb_adapter *adapter = netdev_priv(netdev);
++	struct e1000_hw *hw = &adapter->hw;
+ 	struct mii_ioctl_data *data = if_mii(ifr);
+ 
+-	if (adapter->hw.phy.media_type != e1000_media_type_copper)
++	if (adapter->hw.phy.media_type != e1000_media_type_copper &&
++	    !(rd32(E1000_MDICNFG) & E1000_MDICNFG_EXT_MDIO))
+ 		return -EOPNOTSUPP;
+ 
+ 	switch (cmd) {
+ 	case SIOCGMIIPHY:
+-		data->phy_id = adapter->hw.phy.addr;
++		data->phy_id = hw->phy.addr;
+ 		break;
+ 	case SIOCGMIIREG:
+-		if (igb_read_phy_reg(&adapter->hw, data->reg_num & 0x1F,
+-				     &data->val_out))
+-			return -EIO;
++		if (hw->mac.type == e1000_i210 || hw->mac.type == e1000_i211) {
++			if (igb_read_reg_gs40g(&adapter->hw, data->phy_id,
++					       data->reg_num & 0x1F,
++			                       &data->val_out))
++				return -EIO;
++		} else {
++			if (igb_read_phy_reg(&adapter->hw, data->reg_num & 0x1F,
++			                     &data->val_out))
++				return -EIO;
++		}
+ 		break;
+ 	case SIOCSMIIREG:
++		if (hw->mac.type == e1000_i210 || hw->mac.type == e1000_i211) {
++			if (igb_write_reg_gs40g(hw, data->phy_id,
++					        data->reg_num & 0x1F,
++					        data->val_in))
++				return -EIO;
++		} else {
++			if (igb_write_phy_reg(hw, data->reg_num & 0x1F,
++					      data->val_in))
++				return -EIO;
++		}
++		break;
+ 	default:
+ 		return -EOPNOTSUPP;
+ 	}
diff --git a/target/linux/imx6/patches-4.3/205-phy-add-driver-for-GW16083-Ethernet-Expansion-Mezzan.patch b/target/linux/imx6/patches-4.3/205-phy-add-driver-for-GW16083-Ethernet-Expansion-Mezzan.patch
new file mode 100644
index 0000000..a2ca325
--- /dev/null
+++ b/target/linux/imx6/patches-4.3/205-phy-add-driver-for-GW16083-Ethernet-Expansion-Mezzan.patch
@@ -0,0 +1,31 @@
+Index: linux-4.3/drivers/net/phy/Kconfig
+===================================================================
+--- linux-4.3.orig/drivers/net/phy/Kconfig	2015-12-18 10:39:44.371158315 -0800
++++ linux-4.3/drivers/net/phy/Kconfig	2015-12-18 10:39:44.951158318 -0800
+@@ -309,6 +309,14 @@
+ 
+ source "drivers/net/phy/b53/Kconfig"
+ 
++config GATEWORKS_GW16083
++	tristate "Gateworks GW16083 Ethernet Expansion Mezzanine"
++	---help---
++	  The Gateworks GW16083 Ethernet Expansion Mezzanine connects to a
++	  Gateworks Ventana baseboard and provides a 7-port GbE managed
++	  Ethernet switch with 4 dedicated GbE RJ45 ports, and 2 Gbe/SFP
++	  ports"
++
+ endif # PHYLIB
+ 
+ config MICREL_KS8995MA
+Index: linux-4.3/drivers/net/phy/Makefile
+===================================================================
+--- linux-4.3.orig/drivers/net/phy/Makefile	2015-12-18 10:39:44.371158315 -0800
++++ linux-4.3/drivers/net/phy/Makefile	2015-12-18 10:39:44.951158318 -0800
+@@ -44,6 +44,7 @@
+ obj-$(CONFIG_DP83867_PHY)	+= dp83867.o
+ obj-$(CONFIG_STE10XP)		+= ste10Xp.o
+ obj-$(CONFIG_MICREL_PHY)	+= micrel.o
++obj-$(CONFIG_GATEWORKS_GW16083)	+= gw16083.o
+ obj-$(CONFIG_MDIO_OCTEON)	+= mdio-octeon.o
+ obj-$(CONFIG_MICREL_KS8995MA)	+= spi_ks8995.o
+ obj-$(CONFIG_AT803X_PHY)	+= at803x.o
diff --git a/target/linux/imx6/patches-4.3/206-ARM-imx-ventana-added-GW16083-to-device-tree.patch b/target/linux/imx6/patches-4.3/206-ARM-imx-ventana-added-GW16083-to-device-tree.patch
new file mode 100644
index 0000000..81fbe0e
--- /dev/null
+++ b/target/linux/imx6/patches-4.3/206-ARM-imx-ventana-added-GW16083-to-device-tree.patch
@@ -0,0 +1,64 @@
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi	2015-12-18 10:39:44.895158318 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi	2015-12-18 10:43:21.000000000 -0800
+@@ -158,6 +158,11 @@
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&pinctrl_i2c2>;
+ 	status = "okay";
++
++	gw16083: gw16083 at 52 {
++		compatible = "gateworks,gw16083";
++		reg = <0x52>;
++	};
+ };
+ 
+ &i2c3 {
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi	2015-12-18 10:39:44.907158318 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi	2015-12-18 10:43:21.000000000 -0800
+@@ -233,6 +233,11 @@
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&pinctrl_i2c2>;
+ 	status = "okay";
++
++	gw16083: gw16083 at 52 {
++		compatible = "gateworks,gw16083";
++		reg = <0x52>;
++	};
+ };
+ 
+ &i2c3 {
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi	2015-12-18 10:39:44.899158318 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi	2015-12-18 10:43:25.000000000 -0800
+@@ -226,6 +226,11 @@
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&pinctrl_i2c2>;
+ 	status = "okay";
++
++	gw16083: gw16083 at 52 {
++		compatible = "gateworks,gw16083";
++		reg = <0x52>;
++	};
+ };
+ 
+ &i2c3 {
+Index: linux-4.3/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
+===================================================================
+--- linux-4.3.orig/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi	2015-12-18 10:39:44.899158318 -0800
++++ linux-4.3/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi	2015-12-18 10:43:25.000000000 -0800
+@@ -317,6 +317,11 @@
+ 			};
+ 		};
+ 	};
++
++	gw16083: gw16083 at 52 {
++		compatible = "gateworks,gw16083";
++		reg = <0x52>;
++	};
+ };
+ 
+ &i2c3 {
-- 
2.6.4

_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list