[OpenWrt-Devel] [Patch] [ar71xx] added support for TL-WA830RE V2
Fredrik Jonson
fredrik at famjonson.se
Sat Jul 12 09:40:36 EDT 2014
Corrected patch ath79 insted of auth79. Sorry.
Signed-off-by: Fredrik Jonson <fredrik at famjonson.se>
---
target/linux/ar71xx/base-files/etc/diag.sh | 1 +
.../ar71xx/base-files/etc/uci-defaults/01_leds | 5 +
.../ar71xx/base-files/etc/uci-defaults/02_network | 1 +
target/linux/ar71xx/base-files/lib/ar71xx.sh | 3 +
.../ar71xx/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ar71xx/config-3.10 | 1 +
.../files/arch/mips/ath79/mach-tl-wa830re-v2.c | 132 +++++++++++++++++++++
target/linux/ar71xx/image/Makefile | 3 +-
target/linux/ar71xx/mikrotik/config-default | 1 +
.../714-MIPS-ath79-add-TL-WA830REv2-support.patch | 42 +++++++
10 files changed, 189 insertions(+), 1 deletion(-)
create mode 100644 target/linux/ar71xx/files/arch/mips/ath79/mach-tl-wa830re-v2.c
create mode 100644 target/linux/ar71xx/patches-3.10/714-MIPS-ath79-add-TL-WA830REv2-support.patch
diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh
index ef172b4..d2e4937 100755
--- a/target/linux/ar71xx/base-files/etc/diag.sh
+++ b/target/linux/ar71xx/base-files/etc/diag.sh
@@ -184,6 +184,7 @@ get_status_led() {
tl-wr841n-v1 | \
tl-wr841n-v7 | \
tl-wr841n-v8 | \
+ tl-wa830re-v2 | \
tl-wr842n-v2 | \
tl-wr941nd)
status_led="tp-link:green:system"
diff --git a/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds b/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
index fe5ff93..ebc8942 100755
--- a/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
+++ b/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
@@ -286,6 +286,11 @@ tl-wr841n-v8)
ucidef_set_led_wlan "wlan" "WLAN" "tp-link:green:wlan" "phy0tpt"
;;
+tl-wa830re-v2)
+ ucidef_set_led_netdev "lan" "LAN" "tp-link:green:lan" "eth0"
+ ucidef_set_led_wlan "wlan" "WLAN" "tp-link:green:wlan" "phy0tpt"
+ ;;
+
tl-wr841n-v9)
ucidef_set_led_netdev "wan" "WAN" "tp-link:green:wan" "eth1"
ucidef_set_led_switch "lan1" "LAN1" "tp-link:green:lan1" "switch0" "0x10"
diff --git a/target/linux/ar71xx/base-files/etc/uci-defaults/02_network b/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
index 646425c..6a43d03 100755
--- a/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
+++ b/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
@@ -269,6 +269,7 @@ tl-mr3040 |\
tl-mr3040-v2 |\
tl-wa750re |\
tl-wa850re |\
+tl-wa830re-v2 |\
tl-wa801nd-v2 |\
tl-wa901nd |\
tl-wa901nd-v2 |\
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index bd277ab..88a1c86 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -541,6 +541,9 @@ ar71xx_board_detect() {
*TL-WA850RE)
name="tl-wa850re"
;;
+ *"TL-WA830RE v2")
+ name="tl-wa830re-v2"
+ ;;
*"TL-WA801ND v2")
name="tl-wa801nd-v2"
;;
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
index 8af9580..8f3b563 100755
--- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
@@ -253,6 +253,7 @@ platform_check_image() {
tl-wr741nd | \
tl-wr741nd-v4 | \
tl-wr841n-v1 | \
+ tl-wa830re-v2 | \
tl-wr841n-v7 | \
tl-wr841n-v8 | \
tl-wr841n-v9 | \
diff --git a/target/linux/ar71xx/config-3.10 b/target/linux/ar71xx/config-3.10
index 4e30a44..fbd22b9 100644
--- a/target/linux/ar71xx/config-3.10
+++ b/target/linux/ar71xx/config-3.10
@@ -82,6 +82,7 @@ CONFIG_ATH79_MACH_TL_MR11U=y
CONFIG_ATH79_MACH_TL_MR13U=y
CONFIG_ATH79_MACH_TL_MR3020=y
CONFIG_ATH79_MACH_TL_MR3X20=y
+CONFIG_ATH79_MACH_TL_WA830RE_V2=y
CONFIG_ATH79_MACH_TL_WA901ND=y
CONFIG_ATH79_MACH_TL_WA901ND_V2=y
CONFIG_ATH79_MACH_TL_WAX50RE=y
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-tl-wa830re-v2.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-tl-wa830re-v2.c
new file mode 100644
index 0000000..1c74fed
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-tl-wa830re-v2.c
@@ -0,0 +1,132 @@
+/*
+ * TP-LINK TL-WA830RE v2 board support
+ *
+ * Copyright (C) 2014 Fredrik Jonson <fredrik at famjonson.se>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach-ath79/ath79.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include "common.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+
+#define TL_WA830REV2_GPIO_LED_WLAN 13
+#define TL_WA830REV2_GPIO_LED_QSS 15
+#define TL_WA830REV2_GPIO_LED_LAN 18
+#define TL_WA830REV2_GPIO_LED_SYSTEM 14
+
+#define TL_WA830REV2_GPIO_BTN_RESET 17
+#define TL_WA830REV2_GPIO_SW_RFKILL 16 /* WPS for MR3420 v2 */
+
+#define TL_WA830REV2_GPIO_USB_POWER 4
+
+#define TL_WA830REV2_KEYS_POLL_INTERVAL 20 /* msecs */
+#define TL_WA830REV2_KEYS_DEBOUNCE_INTERVAL (3 * TL_WA830REV2_KEYS_POLL_INTERVAL)
+
+static const char *tl_wa830re_v2_part_probes[] = {
+ "tp-link",
+ NULL,
+};
+
+static struct flash_platform_data tl_wa830re_v2_flash_data = {
+ .part_probes = tl_wa830re_v2_part_probes,
+};
+
+static struct gpio_led tl_wa830re_v2_leds_gpio[] __initdata = {
+ {
+ .name = "tp-link:green:qss",
+ .gpio = TL_WA830REV2_GPIO_LED_QSS,
+ .active_low = 1,
+ }, {
+ .name = "tp-link:green:system",
+ .gpio = TL_WA830REV2_GPIO_LED_SYSTEM,
+ .active_low = 1,
+ }, {
+ .name = "tp-link:green:lan",
+ .gpio = TL_WA830REV2_GPIO_LED_LAN,
+ .active_low = 1,
+ }, {
+ .name = "tp-link:green:wlan",
+ .gpio = TL_WA830REV2_GPIO_LED_WLAN,
+ .active_low = 1,
+ },
+};
+
+static struct gpio_keys_button tl_wa830re_v2_gpio_keys[] __initdata = {
+ {
+ .desc = "Reset button",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = TL_WA830REV2_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = TL_WA830REV2_GPIO_BTN_RESET,
+ .active_low = 1,
+ }, {
+ .desc = "RFKILL switch",
+ .type = EV_SW,
+ .code = KEY_RFKILL,
+ .debounce_interval = TL_WA830REV2_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = TL_WA830REV2_GPIO_SW_RFKILL,
+ .active_low = 0,
+ }
+};
+
+static void __init tl_ap123_setup(void)
+{
+ u8 *mac = (u8 *) KSEG1ADDR(0x1f01fc00);
+ u8 *ee = (u8 *) KSEG1ADDR(0x1fff1000);
+
+ /* Disable JTAG, enabling GPIOs 0-3 */
+ /* Configure OBS4 line, for GPIO 4*/
+ ath79_gpio_function_setup(AR934X_GPIO_FUNC_JTAG_DISABLE,
+ AR934X_GPIO_FUNC_CLK_OBS4_EN);
+
+ /* config gpio4 as normal gpio function */
+ ath79_gpio_output_select(TL_WA830REV2_GPIO_USB_POWER,
+ AR934X_GPIO_OUT_GPIO);
+
+ ath79_register_m25p80(&tl_wa830re_v2_flash_data);
+
+ ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_SW_PHY_SWAP);
+
+ ath79_register_mdio(1, 0x0);
+
+ ath79_init_mac(ath79_eth0_data.mac_addr, mac, 0);
+
+ /* GMAC0 is connected to the PHY0 of the internal switch */
+ ath79_switch_data.phy4_mii_en = 1;
+ ath79_switch_data.phy_poll_mask = BIT(0);
+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
+ ath79_eth0_data.phy_mask = BIT(0);
+ ath79_eth0_data.mii_bus_dev = &ath79_mdio1_device.dev;
+ ath79_register_eth(0);
+
+ ath79_register_wmac(ee, mac);
+}
+
+static void __init tl_wa830re_v2_setup(void)
+{
+ tl_ap123_setup();
+
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(tl_wa830re_v2_leds_gpio) - 1,
+ tl_wa830re_v2_leds_gpio);
+
+ ath79_register_gpio_keys_polled(1, TL_WA830REV2_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(tl_wa830re_v2_gpio_keys),
+ tl_wa830re_v2_gpio_keys);
+}
+
+MIPS_MACHINE(ATH79_MACH_TL_WA830RE_V2, "TL-WA830RE-v2", "TP-LINK TL-WA830RE v2",
+ tl_wa830re_v2_setup);
diff --git a/target/linux/ar71xx/image/Makefile b/target/linux/ar71xx/image/Makefile
index 6bc1105..4b5f502 100644
--- a/target/linux/ar71xx/image/Makefile
+++ b/target/linux/ar71xx/image/Makefile
@@ -1149,6 +1149,7 @@ $(eval $(call SingleProfile,TPLINK-LZMA,64kraw,TLWR741NV4,tl-wr741nd-v4,TL-WR741
$(eval $(call SingleProfile,TPLINK-LZMA,64kraw,TLWR743NV2,tl-wr743nd-v2,TL-WR741ND-v4,ttyATH0,115200,0x07430002,1,4Mlzma))
$(eval $(call SingleProfile,TPLINK-LZMA,64kraw,TLWA750,tl-wa750re-v1,TL-WA750RE,ttyS0,115200,0x07500001,1,4Mlzma))
$(eval $(call SingleProfile,TPLINK-LZMA,64kraw,TLWR841NV8,tl-wr841n-v8,TL-WR841N-v8,ttyS0,115200,0x08410008,1,4Mlzma))
+$(eval $(call SingleProfile,TPLINK-LZMA,64kraw,TLWA830RV2,tl-wa830re-v2,TL-WA830RE-v2,ttyS0,115200,0x08300002,1,4Mlzma))
$(eval $(call SingleProfile,TPLINK-LZMA,64kraw,TLWR841NV9,tl-wr841n-v9,TL-WR841N-v9,ttyS0,115200,0x08410009,1,4Mlzma))
$(eval $(call SingleProfile,TPLINK-LZMA,64kraw,TLWR842V2,tl-wr842n-v2,TL-WR842N-v2,ttyS0,115200,0x8420002,1,8Mlzma))
$(eval $(call SingleProfile,TPLINK-LZMA,64kraw,TLWA801NV2,tl-wa801nd-v2,TL-WA801ND-v2,ttyS0,115200,0x08010002,1,4Mlzma))
@@ -1214,7 +1215,7 @@ $(eval $(call MultiProfile,TLMR3220,TLMR3220V1 TLMR3220V2))
$(eval $(call MultiProfile,TLMR3420,TLMR3420V1 TLMR3420V2))
$(eval $(call MultiProfile,TLWA730RE,TLWA730REV1))
$(eval $(call MultiProfile,TLWA801,TLWA801NV1 TLWA801NV2))
-$(eval $(call MultiProfile,TLWA830,TLWA830RV1))
+$(eval $(call MultiProfile,TLWA830,TLWA830RV1 TLWA830RV2))
$(eval $(call MultiProfile,TLWA901,TLWA901NV1 TLWA901NV2 TLWA901NV3))
$(eval $(call MultiProfile,TLWA7510,TLWA7510NV1))
$(eval $(call MultiProfile,TLWR720,TLWR720NV3))
diff --git a/target/linux/ar71xx/mikrotik/config-default b/target/linux/ar71xx/mikrotik/config-default
index 39d3e60..8923015 100644
--- a/target/linux/ar71xx/mikrotik/config-default
+++ b/target/linux/ar71xx/mikrotik/config-default
@@ -50,6 +50,7 @@ CONFIG_ATH79_MACH_RBSXTLITE=y
# CONFIG_ATH79_MACH_TL_MR13U is not set
# CONFIG_ATH79_MACH_TL_MR3020 is not set
# CONFIG_ATH79_MACH_TL_MR3X20 is not set
+# CONFIG_ATH79_MACH_TL_WA830RE_V2 is not set
# CONFIG_ATH79_MACH_TL_WA901ND is not set
# CONFIG_ATH79_MACH_TL_WA901ND_V2 is not set
# CONFIG_ATH79_MACH_TL_WDR3500 is not set
diff --git a/target/linux/ar71xx/patches-3.10/714-MIPS-ath79-add-TL-WA830REv2-support.patch b/target/linux/ar71xx/patches-3.10/714-MIPS-ath79-add-TL-WA830REv2-support.patch
new file mode 100644
index 0000000..65f4801
--- /dev/null
+++ b/target/linux/ar71xx/patches-3.10/714-MIPS-ath79-add-TL-WA830REv2-support.patch
@@ -0,0 +1,42 @@
+--- a/arch/mips/ath79/Kconfig
++++ b/arch/mips/ath79/Kconfig
+@@ -647,7 +647,17 @@ config ATH79_MACH_TL_WAX50RE
+ select ATH79_DEV_LEDS_GPIO
+ select ATH79_DEV_M25P80
+ select ATH79_DEV_WMAC
+-
++
++config ATH79_MACH_TL_WA830RE_V2
++ bool "TP-LINK TL-WA830RE v2 support"
++ select SOC_AR934X
++ select ATH79_DEV_ETH
++ select ATH79_DEV_GPIO_BUTTONS
++ select ATH79_DEV_LEDS_GPIO
++ select ATH79_DEV_M25P80
++ select ATH79_DEV_USB
++ select ATH79_DEV_WMAC
++
+ config ATH79_MACH_TL_WA901ND
+ bool "TP-LINK TL-WA901ND/TL-WA7510N support"
+ select SOC_AR724X
+--- a/arch/mips/ath79/Makefile
++++ b/arch/mips/ath79/Makefile
+@@ -95,6 +95,7 @@ obj-$(CONFIG_ATH79_MACH_TL_MR13U) += mac
+ obj-$(CONFIG_ATH79_MACH_TL_MR3020) += mach-tl-mr3020.o
+ obj-$(CONFIG_ATH79_MACH_TL_MR3X20) += mach-tl-mr3x20.o
+ obj-$(CONFIG_ATH79_MACH_TL_WAX50RE) += mach-tl-wax50re.o
++obj-$(CONFIG_ATH79_MACH_TL_WA830RE_V2) += mach-tl-wa830re-v2.o
+ obj-$(CONFIG_ATH79_MACH_TL_WA901ND) += mach-tl-wa901nd.o
+ obj-$(CONFIG_ATH79_MACH_TL_WA901ND_V2) += mach-tl-wa901nd-v2.o
+ obj-$(CONFIG_ATH79_MACH_TL_WDR3500) += mach-tl-wdr3500.o
+--- a/arch/mips/ath79/machtypes.h
++++ b/arch/mips/ath79/machtypes.h
+@@ -112,6 +112,7 @@ enum ath79_mach_type {
+ ATH79_MACH_TL_WA7510N_V1, /* TP-LINK TL-WA7510N v1*/
+ ATH79_MACH_TL_WA850RE, /* TP-LINK TL-WA850RE */
+ ATH79_MACH_TL_WA801ND_V2, /* TP-LINK TL-WA801ND v2 */
++ ATH79_MACH_TL_WA830RE_V2, /* TP-LINK TL-WA830RE v2 */
+ ATH79_MACH_TL_WA901ND, /* TP-LINK TL-WA901ND */
+ ATH79_MACH_TL_WA901ND_V2, /* TP-LINK TL-WA901ND v2 */
+ ATH79_MACH_TL_WA901ND_V3, /* TP-LINK TL-WA901ND v3
+
--
1.8.4.5
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list