[OpenWrt-Devel] [PATCH] ramips:Add support for Aigale Ai-BR100

郭传鈜 gch981213 at gmail.com
Fri Dec 12 21:41:24 EST 2014


Aigale Ai-BR100 is a router with mt7620a soc.
There are only 2 lights on the board (WAN and WLAN) so I used the wlan light as the status led.

Signed-off-by: 郭传鈜 <gch981213 at gmail.com>
---
 target/linux/ramips/base-files/etc/board.d/01_leds |   4 +
 .../linux/ramips/base-files/etc/board.d/02_network |   1 +
 target/linux/ramips/base-files/etc/diag.sh         |   3 +
 target/linux/ramips/base-files/lib/ramips.sh       |   3 +
 .../ramips/base-files/lib/upgrade/platform.sh      |   1 +
 target/linux/ramips/dts/AIBR100.dts                | 106 +++++++++++++++++++++
 target/linux/ramips/image/Makefile                 |   3 +
 target/linux/ramips/mt7620/profiles/aigale.mk      |  20 ++++
 8 files changed, 141 insertions(+)
 create mode 100644 target/linux/ramips/dts/AIBR100.dts
 create mode 100644 target/linux/ramips/mt7620/profiles/aigale.mk

diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index bd8c779..9c49c5c 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -27,6 +27,10 @@ case $board in
 	3g300m)
 		set_usb_led "tenda:blue:3g"
 		;;
+	ai-br100)
+		ucidef_set_led_netdev "wan" "wan" "aigale:blue:wan" "eth0.2"
+		set_wifi_led "aigale:blue:wlan"
+		;;
 	a5-v11)
 		ucidef_set_led_default "power" "POWER" "a5-v11:red:power" "1"
 		;;
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index b519cfd..80b5449 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -110,6 +110,7 @@ ramips_setup_interfaces()
 		;;
 
 	3g-6200n | \
+	ai-br100 | \
 	dir-610-a1 | \
 	dir-300-b7 | \
 	dir-320-b1 | \
diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index dfa5468..f50ae1f 100755
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -12,6 +12,9 @@ get_status_led() {
 	3g300m | w150m)
 		status_led="tenda:blue:ap"
 		;;
+	ai-br100)
+		status_led="aigale:blue:wlan"
+		;;
 	ar670w)
 		status_led="ar670w:green:power"
 		;;
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index ff5044c..b4e5d91 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -28,6 +28,9 @@ ramips_board_detect() {
 	*"A5-V11")
 		name="a5-v11"
 		;;
+	*"Aigale Ai-BR100")
+		name="ai-br100"
+		;;
 	*"Airlink101 AR670W")
 		name="ar670w"
 		;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index 4962b8b..991d3b5 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -19,6 +19,7 @@ platform_check_image() {
 	3g300m | \
 	a5-v11 | \
 	air3gii | \
+	ai-br100 |\
 	all0239-3g | \
 	all0256n | \
 	all5002 | \
diff --git a/target/linux/ramips/dts/AIBR100.dts b/target/linux/ramips/dts/AIBR100.dts
new file mode 100644
index 0000000..90f3a1e
--- /dev/null
+++ b/target/linux/ramips/dts/AIBR100.dts
@@ -0,0 +1,106 @@
+/dts-v1/;
+
+/include/ "mt7620a.dtsi"
+
+/ {
+	compatible = "AIBR100", "ralink,mt7620a-soc";
+	model = "Aigale Ai-BR100";
+
+	palmbus at 10000000 {
+		gpio2: gpio at 660 {
+			status = "okay";
+		};
+
+		gpio3: gpio at 688 {
+			status = "okay";
+		};
+
+		spi at b00 {
+			status = "okay";
+
+			m25p80 at 0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "en25q64";
+				reg = <0 0>;
+				linux,modalias = "m25p80", "en25q64";
+				spi-max-frequency = <10000000>;
+
+				partition at 0 {
+					label = "u-boot";
+					reg = <0x0 0x20000>;
+					read-only;
+				};
+
+				partition at 20000 {
+					label = "u-boot-env";
+					reg = <0x20000 0x10000>;
+					read-only;
+				};
+
+				factory: partition at 30000 {
+					label = "factory";
+					reg = <0x30000 0x10000>;
+					read-only;
+				};
+
+				partition at 40000 {
+					label = "firmware";
+					reg = <0x40000 0x7c0000>;
+				};
+			};
+		};
+	};
+
+	ehci at 101c0000 {
+		status = "okay";
+	};
+
+	ohci at 101c1000 {
+		status = "okay";
+	};
+
+	pinctrl {
+		state_default: pinctrl0 {
+			gpio {
+				ralink,group = "i2c", "uartf", "rgmii1", "rgmii2", "ephy", "wled", "nd_sd";
+				ralink,function = "gpio";
+			};
+		};
+	};
+
+	ethernet at 10100000 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&ephy_pins>;
+		mtd-mac-address = <&factory 0x4>;
+		ralink,port-map = "llllw";
+	};
+
+	wmac at 10180000 {
+		ralink,mtd-eeprom = <&factory 0>;
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		wan {
+			label = "aigale:blue:wan";
+			gpios = <&gpio2 4 1>;
+		};
+		wlan {
+			label = "aigale:blue:wlan";
+			gpios = <&gpio3 0 1>;
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <20>;
+		reset {
+			label = "reset";
+			gpios = <&gpio0 12 1>;
+			linux,code = <0x198>;
+		};
+	};
+};
diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile
index e0eb8c2..c5478ce 100644
--- a/target/linux/ramips/image/Makefile
+++ b/target/linux/ramips/image/Makefile
@@ -770,6 +770,8 @@ Image/Build/Profile/MT7620a=$(call BuildFirmware/Default8M/$(1),$(1),mt7620a,MT7
 Image/Build/Profile/MT7620a_MT7610e=$(call BuildFirmware/Default8M/$(1),$(1),mt7620a_mt7610e,MT7620a_MT7610e)
 Image/Build/Profile/MT7620a_MT7530=$(call BuildFirmware/Default8M/$(1),$(1),mt7620a_mt7530,MT7620a_MT7530)
 Image/Build/Profile/MT7620a_V22SG=$(call BuildFirmware/Default8M/$(1),$(1),mt7620a_v22sg,MT7620a_V22SG)
+br100_mtd_size=8126464
+Image/Build/Profile/AIBR100=$(call BuildFirmware/CustomFlash/$(1),$(1),ai-br100,AIBR100,$(br100_mtd_size),Ai-BR)
 Image/Build/Profile/RP-N53=$(call BuildFirmware/Default8M/$(1),$(1),rp_n53,RP-N53)
 whr_300hp2_mtd_size=7012352
 Image/Build/Profile/WHR300HP2=$(call BuildFirmware/CustomFlash/$(1),$(1),whr-300hp2,WHR-300HP2,$(whr_300hp2_mtd_size))
@@ -799,6 +801,7 @@ define Image/Build/Profile/Default
 	$(call Image/Build/Profile/MT7620a_MT7610e,$(1))
 	$(call Image/Build/Profile/MT7620a_MT7530,$(1))
 	$(call Image/Build/Profile/MT7620a_V22SG,$(1))
+	$(call Image/Build/Profile/AIBR100,$(1))
 	$(call Image/Build/Profile/RP-N53,$(1))
 	$(call Image/Build/Profile/DIR-810L,$(1))
 	$(call Image/Build/Profile/WHR300HP2,$(1))
diff --git a/target/linux/ramips/mt7620/profiles/aigale.mk b/target/linux/ramips/mt7620/profiles/aigale.mk
new file mode 100644
index 0000000..e58ac43
--- /dev/null
+++ b/target/linux/ramips/mt7620/profiles/aigale.mk
@@ -0,0 +1,20 @@
+#
+# Copyright (C) 2014 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/AIBR100
+	NAME:=Aigale Ai-BR100
+	PACKAGES:=\
+		kmod-usb-core \
+		kmod-usb-ohci \
+		kmod-ledtrig-usbdev \
+		kmod-usb2
+endef
+
+define Profile/AIBR100/Description
+	Default package set for Aigale Ai-BR100.
+endef
+$(eval $(call Profile,AIBR100))
-- 
2.1.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel


More information about the openwrt-devel mailing list