[OpenWrt-Devel] [PATCH 1/3] uboot-oxnas: re-add IC+ phy driver

John Crispin blogic at openwrt.org
Thu Dec 4 01:30:37 EST 2014


i recently removed the driver from the ralink kernel as it made the
link unstable. how does the phy behave for you without the drive
strength quirk ? does the linux phy driver work for you on this HW ?
i looked for the datasheet but failed to find it. do you have it ?



On 03/12/2014 16:03, Daniel Golle wrote:
> KD20 got an IC+ phy, without the driver the phy is not properly 
> initialized resulting in ethernet not working unless being already 
> initialized by the vendor loader.
> 
> upstream commit 368b4d2b49bbbf379d9334747fbbd2aaaafe4356 drivers:
> net: remove dead drivers removed icplus.c due to the lack of
> in-tree users. Partially revert that commit adding back the IC+
> driver.
> 
> Signed-off-by: Daniel Golle <daniel at makrotopia.org> --- 
> .../boot/uboot-oxnas/files/include/configs/ox820.h |   1 + 
> .../boot/uboot-oxnas/patches/200-icplus-phy.patch  | 129
> +++++++++++++++++++++ 2 files changed, 130 insertions(+) create
> mode 100644 package/boot/uboot-oxnas/patches/200-icplus-phy.patch
> 
> diff --git a/package/boot/uboot-oxnas/files/include/configs/ox820.h
> b/package/boot/uboot-oxnas/files/include/configs/ox820.h index
> e3c71e6..85ee3b4 100644 ---
> a/package/boot/uboot-oxnas/files/include/configs/ox820.h +++
> b/package/boot/uboot-oxnas/files/include/configs/ox820.h @@ -76,6
> +76,7 @@ #define CONFIG_CMD_MII #define CONFIG_PHYLIB #define
> CONFIG_PHY_REALTEK +#define CONFIG_PHY_ICPLUS
> 
> /* spl */ #ifdef CONFIG_SPL_BUILD diff --git
> a/package/boot/uboot-oxnas/patches/200-icplus-phy.patch
> b/package/boot/uboot-oxnas/patches/200-icplus-phy.patch new file
> mode 100644 index 0000000..3db7816 --- /dev/null +++
> b/package/boot/uboot-oxnas/patches/200-icplus-phy.patch @@ -0,0
> +1,129 @@ +From e719404ee1241af679a51879eaad291bc27e4817 Mon Sep 17
> 00:00:00 2001 +From: Daniel Golle <daniel at makrotopia.org> +Date:
> Tue, 2 Dec 2014 14:46:05 +0100 +Subject: [PATCH] net/phy: add back
> icplus driver + +IC+ phy driver was removed due to the lack of
> users some time ago. +Add it back, so we can use it. +--- +
> drivers/net/phy/Makefile |  1 + + drivers/net/phy/icplus.c | 80
> ++++++++++++++++++++++++++++++++++++++++++++++++ +
> drivers/net/phy/phy.c    |  3 ++ + 3 files changed, 84
> insertions(+) + create mode 100644 drivers/net/phy/icplus.c + +---
> a/drivers/net/phy/Makefile ++++ b/drivers/net/phy/Makefile +@@
> -15,6 +15,7 @@ obj-$(CONFIG_PHY_ATHEROS) += atheros.o +
> obj-$(CONFIG_PHY_BROADCOM) += broadcom.o +
> obj-$(CONFIG_PHY_DAVICOM) += davicom.o + obj-$(CONFIG_PHY_ET1011C)
> += et1011c.o ++obj-$(CONFIG_PHY_ICPLUS) += icplus.o +
> obj-$(CONFIG_PHY_LXT) += lxt.o + obj-$(CONFIG_PHY_MARVELL) +=
> marvell.o + obj-$(CONFIG_PHY_MICREL) += micrel.o +--- /dev/null 
> ++++ b/drivers/net/phy/icplus.c +@@ -0,0 +1,80 @@ ++/* ++ * ICPlus
> PHY drivers ++ * ++ * SPDX-License-Identifier:	GPL-2.0+ ++ * ++ *
> Copyright (c) 2007 Freescale Semiconductor, Inc. ++ */ ++#include
> <phy.h> ++ ++/* IP101A/G - IP1001 */ ++#define
> IP10XX_SPEC_CTRL_STATUS         16      /* Spec. Control Register
> */ ++#define IP1001_SPEC_CTRL_STATUS_2       20      /* IP1001
> Spec. Control Reg 2 */ ++#define IP1001_PHASE_SEL_MASK           3
> /* IP1001 RX/TXPHASE_SEL */ ++#define IP1001_APS_ON
> 11      /* IP1001 APS Mode  bit */ ++#define IP101A_G_APS_ON
> 2       /* IP101A/G APS Mode bit */ ++#define
> IP101A_G_IRQ_CONF_STATUS        0x11    /* Conf Info IRQ & Status
> Reg */ ++#define IP101A_G_IRQ_PIN_USED           (1<<15) /* INTR
> pin used */ ++#define IP101A_G_IRQ_DEFAULT
> IP101A_G_IRQ_PIN_USED ++ ++static int ip1001_config(struct
> phy_device *phydev) ++{ ++	int c; ++ ++	/* Enable Auto Power Saving
> mode */ ++	c = phy_read(phydev, MDIO_DEVAD_NONE,
> IP1001_SPEC_CTRL_STATUS_2); ++	if (c < 0) ++		return c; ++	c |=
> IP1001_APS_ON; ++	c = phy_write(phydev, MDIO_DEVAD_NONE,
> IP1001_SPEC_CTRL_STATUS_2, c); ++	if (c < 0) ++		return c; ++ ++	/*
> INTR pin used: speed/link/duplex will cause an interrupt */ ++	c =
> phy_write(phydev, MDIO_DEVAD_NONE, IP101A_G_IRQ_CONF_STATUS, ++
> IP101A_G_IRQ_DEFAULT); ++	if (c < 0) ++		return c; ++ ++	if
> (phydev->interface == PHY_INTERFACE_MODE_RGMII) { ++		/* ++		 *
> Additional delay (2ns) used to adjust RX clock phase ++		 * at
> RGMII interface ++		 */ ++		c = phy_read(phydev, MDIO_DEVAD_NONE,
> IP10XX_SPEC_CTRL_STATUS); ++		if (c < 0) ++			return c; ++ ++		c |=
> IP1001_PHASE_SEL_MASK; ++		c = phy_write(phydev, MDIO_DEVAD_NONE,
> IP10XX_SPEC_CTRL_STATUS, ++			      c); ++		if (c < 0) ++			return
> c; ++	} ++ ++	return 0; ++} ++ ++static int ip1001_startup(struct
> phy_device *phydev) ++{ ++	genphy_update_link(phydev); ++
> genphy_parse_link(phydev); ++ ++	return 0; ++} ++static struct
> phy_driver IP1001_driver = { ++	.name = "ICPlus IP1001", ++	.uid =
> 0x02430d90, ++	.mask = 0x0ffffff0, ++	.features =
> PHY_GBIT_FEATURES, ++	.config = &ip1001_config, ++	.startup =
> &ip1001_startup, ++	.shutdown = &genphy_shutdown, ++}; ++ ++int
> phy_icplus_init(void) ++{ ++	phy_register(&IP1001_driver); ++ ++
> return 0; ++} +--- a/drivers/net/phy/phy.c ++++
> b/drivers/net/phy/phy.c +@@ -454,6 +454,9 @@ int phy_init(void) +
> #ifdef CONFIG_PHY_ET1011C + 	phy_et1011c_init(); + #endif ++#ifdef
> CONFIG_PHY_ICPLUS ++	phy_icplus_init(); ++#endif + #ifdef
> CONFIG_PHY_LXT + 	phy_lxt_init(); + #endif +--- a/include/phy.h 
> ++++ b/include/phy.h +@@ -225,6 +225,7 @@ int
> phy_atheros_init(void); + int phy_broadcom_init(void); + int
> phy_davicom_init(void); + int phy_et1011c_init(void); ++int
> phy_icplus_init(void); + int phy_lxt_init(void); + int
> phy_marvell_init(void); + int phy_micrel_init(void);
> 
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list