[FS#4137] OpenWRT 21.02.1 doesn't completely boot on RaidSonic IB-NAS4220-B
OpenWrt Bugs
openwrt-bugs at lists.openwrt.org
Sun Nov 28 12:54:51 PST 2021
THIS IS AN AUTOMATED MESSAGE, DO NOT REPLY.
The following task has a new comment added:
FS#4137 - OpenWRT 21.02.1 doesn't completely boot on RaidSonic IB-NAS4220-B
User who did this - Steven Maddox (Lantizia)
----------
Hey Christian,
Sorry to have to report that it appears that build doesn't boot due to a segmentation fault.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.10.82 (builder at buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.2.0 r18216-a662d8550f) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 PREEMPT Sun Nov 28 00:13:08 2021
[ 0.000000] CPU: FA526 [66015261] revision 1 (ARMv4), cr=0000397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] OF: fdt: Machine model: Raidsonic NAS IB-4220-B
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] cma: Reserved 16 MiB at 0x07000000
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,19200n8 root=/dev/mtdblock3 rw rootfstype=squashfs,jffs2 rootwait
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 102172K/131072K available (6704K kernel code, 632K rwdata, 1728K rodata, 1024K init, 245K bss, 12516K reserved, 16384K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] random: get_random_bytes called from start_kernel+0x2e0/0x4e8 with crng_init=0
[ 0.000000] clocksource: FTTMR010-TIMER2: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.000029] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
[ 0.000133] Switching to timer-based delay loop, resolution 40ns
[ 0.000812] Console: colour dummy device 80x30
[ 0.000991] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[ 0.001074] pid_max: default: 32768 minimum: 301
[ 0.001847] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.001950] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.005041] CPU: Testing write buffer coherency: ok
[ 0.009677] Setting up static identity map for 0x100000 - 0x100048
[ 0.010382] rcu: Hierarchical SRCU implementation.
[ 0.010879] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.024614] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.024706] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.028791] pinctrl core: initialized pinctrl subsystem
[ 0.040965] NET: Registered protocol family 16
[ 0.051908] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.077690] thermal_sys: Registered thermal governor 'step_wise'
[ 0.078654] No ATAGs?
[ 0.213562] pinctrl-gemini 40000000.syscon:pinctrl: detected 3516 chip variant
[ 0.213638] pinctrl-gemini 40000000.syscon:pinctrl: GLOBAL MISC CTRL at boot: 0x83c22037
[ 0.213693] pinctrl-gemini 40000000.syscon:pinctrl: flash pin is set
[ 0.215273] pinctrl-gemini 40000000.syscon:pinctrl: initialized Gemini pin control driver
[ 0.554886] pl08xdmac 67000000.dma-controller: FTDMAC020 1.16 rel 1
[ 0.554954] pl08xdmac 67000000.dma-controller: FTDMAC020 4 channels, has built-in bridge, AHB0 and AHB1, supports linked lists
[ 0.555246] pl08xdmac 67000000.dma-controller: initialized 4 virtual memcpy channels
[ 0.556963] pl08xdmac 67000000.dma-controller: DMA: PL080 rev0 at 0x67000000 irq 28
[ 0.572994] Gemini SoC 3516 revision c2, set arbitration 00200030
[ 0.577502] vgaarb: loaded
[ 0.587463] SCSI subsystem initialized
[ 0.629622] clocksource: Switched to clocksource FTTMR010-TIMER2
[ 0.826746] NET: Registered protocol family 2
[ 0.827271] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.833510] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.833744] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.833866] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.833956] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.834475] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.834611] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.835422] NET: Registered protocol family 1
[ 0.835576] PCI: CLS 0 bytes, default 32
[ 0.848542] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.884328] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.884392] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 1.337895] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 1.338635] io scheduler mq-deadline registered
[ 1.338701] io scheduler kyber registered
[ 1.348657] ftgpio010-gpio 4d000000.gpio: FTGPIO010 @(ptrval) registered
[ 1.358583] ftgpio010-gpio 4e000000.gpio: FTGPIO010 @(ptrval) registered
[ 1.372063] ftgpio010-gpio 4f000000.gpio: FTGPIO010 @(ptrval) registered
[ 1.395561] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 1.454377] printk: console [ttyS0] disabled
[ 1.454725] 42000000.serial: ttyS0 at MMIO 0x42000000 (irq = 18, base_baud = 3000000) is a 16550A
[ 4.585263] printk: console [ttyS0] enabled
[ 4.628478] Loading iSCSI transport class v2.0-870.
[ 4.680737] gemini_sata_bridge 46000000.sata: SATA ID 00000e00, PHY ID: 01000100
[ 4.731465] gemini_sata_bridge 46000000.sata: set up the Gemini IDE/SATA nexus
[ 4.778684] pata_ftide010 63000000.ide: set up Gemini PATA0
[ 4.818250] pata_ftide010 63000000.ide: device ID 00000500, irq 26, reg [mem 0x63000000-0x63000fff]
[ 4.873180] pata_ftide010 63000000.ide: SATA0 (master) start
[ 5.069642] random: fast init done
[ 5.090144] gemini_sata_bridge 46000000.sata: SATA0 PHY ready
[ 5.124668] pata_ftide010 63000000.ide: brought 1 bridges online
[ 5.171979] scsi host0: pata_ftide010
[ 5.197782] ata1: SATA max UDMA/133 irq 26
[ 5.227757] pata_ftide010 63400000.ide: set up Gemini PATA1
[ 5.264823] pata_ftide010 63400000.ide: device ID 00000500, irq 27, reg [mem 0x63400000-0x63400fff]
[ 5.320075] pata_ftide010 63400000.ide: SATA1 (master) start
[ 5.439757] ata1.00: HPA detected: current 976771055, native 976773168
[ 5.478968] ata1.00: ATA-8: WDC WD5000AAJS-22YFA0, 12.01C02, max UDMA/133
[ 5.519723] ata1.00: 976771055 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 5.559470] gemini_sata_bridge 46000000.sata: SATA1 PHY ready
[ 5.594533] pata_ftide010 63400000.ide: brought 1 bridges online
[ 5.633699] scsi 0:0:0:0: Direct-Access ATA WDC WD5000AAJS-2 1C02 PQ: 0 ANSI: 5
[ 5.692530] scsi host1: pata_ftide010
[ 5.717882] ata2: SATA max UDMA/133 irq 27
[ 5.751973] sd 0:0:0:0: [sda] 976771055 512-byte logical blocks: (500 GB/466 GiB)
[ 5.811377] physmap-flash 30000000.flash: no enabled pin control state
[ 5.857668] physmap-flash 30000000.flash: no disabled pin control state
[ 5.898137] sd 0:0:0:0: [sda] Write Protect is off
[ 5.927931] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.983003] physmap-flash 30000000.flash: initialized Gemini-specific physmap control
[ 6.030720] ata2.00: HPA detected: current 976771055, native 976773168
[ 6.092776] sda: sda1 sda2 sda3
[ 6.113574] physmap-flash 30000000.flash: physmap platform flash device: [mem 0x30000000-0x30ffffff]
[ 6.181527] ata2.00: ATA-7: SAMSUNG HD502IJ, 1AA01113, max UDMA7
[ 6.219078] sd 0:0:0:0: [sda] Attached SCSI disk
[ 6.249520] 30000000.flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101
[ 6.310788] ata2.00: 976771055 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 6.351201] Amd/Fujitsu Extended Query Table at 0x0040
[ 6.384231] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD502IJ 1113 PQ: 0 ANSI: 5
[ 6.432902] Amd/Fujitsu Extended Query version 1.3.
[ 6.463368] number of CFI chips: 1
[ 6.489845] sd 1:0:0:0: [sdb] 976771055 512-byte logical blocks: (500 GB/466 GiB)
[ 6.545664] Searching for RedBoot partition table in 30000000.flash at offset 0xfe0000
[ 6.593698] sd 1:0:0:0: [sdb] Write Protect is off
[ 6.643536] 7 RedBoot partitions found on MTD device 30000000.flash
[ 6.681857] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.736180] Creating 7 MTD partitions on "30000000.flash":
[ 6.776981] 0x000000000000-0x000000020000 : "BOOT"
[ 6.806990] sdb: sdb1 sdb2 sdb3
[ 6.829570] 0x000000020000-0x000000220000 : "Kern"
[ 6.877363] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 6.908457] 0x000000320000-0x000000448576 : "Ramdisk"
[ 6.946137] mtd: partition "Ramdisk" doesn't end on an erase/write block -- force read-only
[ 6.999540] 0x000000920000-0x000000f20000 : "Application"
[ 7.039586] 0x000000f20000-0x000000f40000 : "VCTL"
[ 7.076999] 0x000000f40000-0x000000fe0000 : "CurConf"
[ 7.115289] 0x000000fe0000-0x000001000000 : "FIS directory"
[ 7.238366] libphy: Fixed MDIO Bus: probed
[ 7.297700] mdio-gpio mdio: failed to get alias id
[ 7.390995] libphy: GPIO Bitbanged MDIO: probed
[ 7.444258] gmac-gemini 60000000.ethernet: Ethernet device ID: 0x000, revision 0x1
[ 7.492889] gemini-ethernet-port 60008000.ethernet-port: probe 60008000.ethernet-port ID 0
[ 7.546699] gemini-ethernet-port 60008000.ethernet-port: using a random ethernet address
[ 7.671101] Marvell 88E1118 gpio-0:01: attached PHY driver [Marvell 88E1118] (mii_bus:phy_addr=gpio-0:01, irq=POLL)
[ 7.736339] gemini-ethernet-port 60008000.ethernet-port eth0: irq 31, DMA @ 0x0x60008000, GMAC @ 0x0x6000a000
[ 7.802972] gemini-ethernet-port 6000c000.ethernet-port: probe 6000c000.ethernet-port ID 1
[ 7.859905] gemini-ethernet-port 6000c000.ethernet-port: using a random ethernet address
[ 7.909252] gemini-ethernet-port 6000c000.ethernet-port (unnamed net_device) (uninitialized): PHY init failed
[ 7.976041] rtc-ftrtc010 45000000.rtc: registered as rtc0
[ 8.020693] rtc-ftrtc010 45000000.rtc: setting system clock to 1970-01-01T00:00:00 UTC (0)
[ 8.074193] gemini-poweroff 4b000000.power-controller: Gemini poweroff driver registered
[ 8.203213] ftwdt010-wdt 41000000.watchdog: FTWDT010 watchdog driver enabled
[ 8.266164] NET: Registered protocol family 10
[ 8.297302] Segment Routing with IPv6
[ 8.320193] NET: Registered protocol family 17
[ 8.347216] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 8.425502] 8021q: 802.1Q VLAN Support v1.8
[ 8.474430] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 8.525489] Freeing unused kernel memory: 1024K
[ 8.579783] Run /sbin/init as init process
[ 9.676628] init: Console is alive
[ 9.698510] init: - watchdog -
[ 13.299949] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 13.591612] usbcore: registered new interface driver usbfs
[ 13.659834] usbcore: registered new interface driver hub
[ 13.729771] usbcore: registered new device driver usb
[ 13.833915] raid6: skip pq benchmark and using algorithm int32x8
[ 13.881514] raid6: using intx1 recovery algorithm
[ 13.914106] xor: measuring software checksum speed
[ 14.019767] arm4regs : 247 MB/sec
[ 14.184037] 8regs : 175 MB/sec
[ 14.319774] 32regs : 224 MB/sec
[ 14.376742] xor: using function: arm4regs (247 MB/sec)
[ 15.484274] Btrfs loaded, crc32c=crc32c-generic
[ 15.590432] gpio-keys gpio_keys: does not support key code:141
[ 15.656339] gpio-keys: probe of gpio_keys failed with error -22
[ 15.761151] fotg210_hcd: FOTG210 Host Controller (EHCI) Driver
[ 15.831440] fotg210-hcd 68000000.usb: initialized Gemini PHY
[ 15.865750] fotg210-hcd 68000000.usb: Faraday USB2.0 Host Controller
[ 15.909888] fotg210-hcd 68000000.usb: new USB bus registered, assigned bus number 1
[ 16.134021] fotg210-hcd 68000000.usb: irq 29, io mem 0x68000000
[ 16.180091] fotg210-hcd 68000000.usb: USB 2.0 started, EHCI 1.00
[ 16.220067] hub 1-0:1.0: USB hub found
[ 16.247129] hub 1-0:1.0: 1 port detected
[ 16.284625] fotg210-hcd 69000000.usb: initialized Gemini PHY
[ 16.321437] fotg210-hcd 69000000.usb: Faraday USB2.0 Host Controller
[ 16.360264] fotg210-hcd 69000000.usb: new USB bus registered, assigned bus number 2
[ 16.407487] fotg210-hcd 69000000.usb: irq 30, io mem 0x69000000
[ 16.453560] fotg210-hcd 69000000.usb: USB 2.0 started, EHCI 1.00
[ 16.493459] hub 2-0:1.0: USB hub found
[ 16.520710] hub 2-0:1.0: 1 port detected
[ 16.611107] usbcore: registered new interface driver usb-storage
[ 16.689990] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 16.785618] init: - preinit -
[ 20.529907] random: jshn: uninitialized urandom read (4 bytes read)
[ 20.924199] random: jshn: uninitialized urandom read (4 bytes read)
[ 21.030835] random: jshn: uninitialized urandom read (4 bytes read)
[ 21.209927] 8
More information about the openwrt-bugs
mailing list