[FS#3938] Akitio MyCloud Mini hangs during boot of akitio_mycloud-initramfs-uImage
OpenWrt Bugs
openwrt-bugs at lists.openwrt.org
Sun Jul 18 23:25:18 PDT 2021
THIS IS AN AUTOMATED MESSAGE, DO NOT REPLY.
A new Flyspray task has been opened. Details are below.
User who did this - Raylynn Knight (RaylynnKnight)
Attached to Project - OpenWrt/LEDE Project
Summary - Akitio MyCloud Mini hangs during boot of akitio_mycloud-initramfs-uImage
Task Type - Bug Report
Category - Base system
Status - Unconfirmed
Assigned To -
Operating System - All
Severity - Critical
Priority - Very Low
Reported Version - openwrt-21.02
Due in Version - Undecided
Due Date - Undecided
Details - Supply the following if possible:
The akitio_mycloud-initramfs-uImage from 21.02.0-rc3 hangs when booting on Akitio MyCloud Mini. This was also reported as an issue in the forums with 19.07 release.
Stage-1 Bootloader 五 10月 28 10:36:29 CST 2011
Attempting to set PLLA to 750MHz ...
plla_ctrl0 : 0x0000000A
plla_ctrl1 : 0x000F0000
plla_ctrl2 : 0x001D01A0
plla_ctrl3 : 0x00000017
PLLA Set
Setup memory, testing, Image 0
Hdr len: 0x0001AC3C
Hdr CRC: 0xB931AD17
OK
U-Boot 1.1.2 (Oct 28 2011 - 10:44:29)
U-Boot code: 60D00000 -> 60D1AC3C BSS: -> 60D1F2F4
RAM Configuration:
Bank #0: 60000000 256 MB
SRAM Configuration:
64KB at 0x50000000
NAND:256 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Setting Linux mem= boot arg value
Reading upgrade flag from NAND address 0x01ec0000 : 0
Hit any key to stop autoboot: 0
$ tftp 64000000 uImage.mycloud
Wait GMAC to reset
Wait for PHY reset
PHY is Realtek RTL8211D
Wait for link to come up................Link up
Wait for auto-negotiation to complete
Link is 1000M
TFTP from server 192.168.50.59; our IP address is 192.168.50.100
Filename 'uImage.mycloud'.
Load address: 0x64000000
Loading:
ARP Resend request
T invalid RARP header
################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
##########################
done
Bytes transferred = 7120489 (6ca669 hex)
$ bootm 64000000
## Booting image at 64000000 ...
Image Name: ARM OpenWrt Linux-5.4.124
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 7120425 Bytes = 6.8 MB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.4.124 (builder at buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16172-2aba3e9784)) #0 SMP Sun Jun 13 22:02:19 2021
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Akitio MyCloud
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] cma: Reserved 64 MiB at 0x64000000
[ 0.000000] percpu: Embedded 15 pages/cpu s29772 r8192 d23476 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: earlyprintk console=ttyS0,115200
[ 0.000000] Bootloader command line (ignored): root=ubi0:rootfs ubi.mtd=2,512 rootfstype=ubifs console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 mem=256M poweroutage=yes
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 47188K/131072K available (6144K kernel code, 171K rwdata, 784K rodata, 9216K init, 214K bss, 18348K reserved, 65536K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] FPGA IRQ chip 0 "interrupt-controller" @ (ptrval), 32 irqs, parent IRQ: 16
[ 0.000000] random: get_random_bytes called from 0xc0800b88 with crng_init=0
[ 0.000020] sched_clock: 24 bits at 390kHz, resolution 2560ns, wraps every 21474835200ns
[ 0.000074] clocksource: oxnas_rps_clocksource_timer: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 19112603332 ns
[ 0.000089] timer_oxnas_rps: Registered clocksource rate 390625Hz
[ 0.000112] timer_oxnas_rps: Registered clock event rate 6250000Hz prescaler 0 period 62500
[ 0.000276] GIC: PPI13 is secure or misconfigured
[ 0.000330] GIC: PPI13 is secure or misconfigured
[ 0.000450] Calibrating delay loop... 298.59 BogoMIPS (lpj=1492992)
[ 0.070307] pid_max: default: 32768 minimum: 301
[ 0.070661] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.070689] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.072107] CPU: Testing write buffer coherency: ok
[ 0.074155] Setting up static identity map for 0x60100000 - 0x6010005c
[ 0.074457] rcu: Hierarchical SRCU implementation.
[ 0.075202] smp: Bringing up secondary CPUs ...
[ 0.076308] GIC: PPI13 is secure or misconfigured
[ 0.140692] smp: Brought up 1 node, 2 CPUs
[ 0.140728] SMP: Total of 2 processors activated (598.42 BogoMIPS).
[ 0.146245] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.146286] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.153093] pinctrl core: initialized pinctrl subsystem
[ 0.154055] NET: Registered protocol family 16
[ 0.158021] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.160611] cpuidle: using governor menu
[ 0.160719] No ATAGs?
[ 0.181959] pps_core: LinuxPPS API ver. 1 registered
[ 0.181982] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.182041] PTP clock support registered
[ 0.182300] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.183626] clocksource: Switched to clocksource oxnas_rps_clocksource_timer
[ 0.185013] thermal_sys: Registered thermal governor 'step_wise'
[ 0.185392] NET: Registered protocol family 2
[ 0.185592] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.187010] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.187092] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.187130] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.187169] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.187343] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.187412] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.187837] NET: Registered protocol family 1
[ 0.187896] PCI: CLS 0 bytes, default 32
[ 0.487014] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.498406] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.499348] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.502737] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.506877] printk: console [ttyS0] disabled
[ 0.507051] 44200000.serial: ttyS0 at MMIO 0x44200000 (irq = 55, base_baud = 390625) is a 16550A
[ 0.967037] printk: console [ttyS0] enabled
[ 0.989649] brd: module loaded
[ 1.004014] loop: module loaded
[ 1.073950] Could not find a valid ONFI parameter page, trying bit-wise majority to recover it
[ 1.082611] ONFI parameter recovery failed, aborting
[ 1.087621] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[ 1.093977] nand: Hynix NAND 256MiB 3,3V 8-bit
[ 1.098403] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.105996] Scanning device for bad blocks
[ 1.161538] Bad eraseblock 618 at 0x000004d40000
[ 1.183211] Bad eraseblock 824 at 0x000006700000
[ 1.190617] Bad eraseblock 858 at 0x000006b40000
[ 1.251353] Bad eraseblock 1536 at 0x00000c000000
[ 1.271260] Bad eraseblock 1720 at 0x00000d700000
[ 1.295429] Bad eraseblock 1955 at 0x00000f460000
[ 1.307783] 2 fixed-partitions partitions found on MTD device 41000000.nand-controller
[ 1.315706] Creating 2 MTD partitions on "41000000.nand-controller":
[ 1.322055] 0x000000000000-0x0000026c0000 : "boot"
[ 1.328936] 0x0000026c0000-0x000010000000 : "ubi"
[ 1.337172] libphy: Fixed MDIO Bus: probed
[ 1.342082] oxnas-dwmac 40400000.ethernet: IRQ eth_lpi not found
[ 1.348318] oxnas-dwmac 40400000.ethernet: PTP uses main clock
[ 1.354201] oxnas-dwmac 40400000.ethernet: no reset control found
[ 1.424023] oxnas-dwmac 40400000.ethernet: User ID: 0x12, Synopsys ID: 0x35
[ 1.430981] oxnas-dwmac 40400000.ethernet: DWMAC1000
[ 1.436070] oxnas-dwmac 40400000.ethernet: DMA HW capability register supported
[ 1.443345] oxnas-dwmac 40400000.ethernet: RX Checksum Offload Engine supported
[ 1.450659] oxnas-dwmac 40400000.ethernet: COE Type 2
[ 1.455723] oxnas-dwmac 40400000.ethernet: TX Checksum insertion supported
[ 1.462563] oxnas-dwmac 40400000.ethernet: Wake-Up On Lan supported
[ 1.468899] oxnas-dwmac 40400000.ethernet: Enhanced/Alternate descriptors
[ 1.475706] oxnas-dwmac 40400000.ethernet: Enabled extended descriptors
[ 1.482291] oxnas-dwmac 40400000.ethernet: Ring mode enabled
[ 1.487953] oxnas-dwmac 40400000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 1.495815] oxnas-dwmac 40400000.ethernet: device MAC address 3e:c3:3f:d1:0c:ca
[ 1.536033] libphy: stmmac: probed
[ 1.539445] RTL8211DN Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[ 1.552128] RTL8211DN Gigabit Ethernet stmmac-0:03: attached PHY driver [RTL8211DN Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:03, irq=POLL)
[ 1.567016] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.573120] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.580288] NET: Registered protocol family 10
[ 1.586462] Segment Routing with IPv6
[ 1.590225] NET: Registered protocol family 17
[ 1.594862] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.607805] 8021q: 802.1Q VLAN Support v1.8
Device hangs at this point.
More information can be found at the following URL:
https://bugs.openwrt.org/index.php?do=details&task_id=3938
You are receiving this message because you have requested it from the Flyspray bugtracking system. If you did not expect this message or don't want to receive mails in future, you can change your notification settings at the URL shown above.
More information about the openwrt-bugs
mailing list