[FS#3438] WiTi Board reboot failure

[OpenWrt Bugs]

THIS IS AN AUTOMATED MESSAGE, DO NOT REPLY.

A new Flyspray task has been opened.  Details are below. 

User who did this - b (rizla3066) 

Attached to Project - OpenWrt/LEDE Project
Summary - WiTi Board reboot failure
Task Type - Bug Report
Category - Base system
Status - Unconfirmed
Assigned To - 
Operating System - All
Severity - Low
Priority - Very Low
Reported Version - Trunk
Due in Version - Undecided
Due Date - Undecided
Details - Supply the following if possible:
 - Device problem occurs on WiTi Board 512MB
 - Software versions of OpenWrt/LEDE release, packages, etc. Al versions
 - Steps to reproduce = Reboot from luci or command line


Issue with device not rebooting when instructed and hanging. At the moment i have to edit the following patch.

**304-spi-nor-enable-4B-opcodes-for-mx25l25635f.patch**

From

--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -1103,6 +1103,7 @@ static const struct flash_info spi_nor_i
 	{ "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) },
 	{ "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
-	{ "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+	{ "mx25l25635f", INFO(0xc22019, 0, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
 	{ "mx25u25635f", INFO(0xc22539, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_4B_OPCODES) },
 	{ "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) },
 	{ "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
@@ -1272,11 +1273,12 @@ static const struct flash_info spi_nor_i
 	{ },
 };

   

To


--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -1103,6 +1103,7 @@ static const struct flash_info spi_nor_i
 	{ "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) },
 	{ "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
-	{ "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+	{ "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_READ_OP) },
+	{ "mx25l25635f", INFO(0xc22019, 0, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
 	{ "mx25u25635f", INFO(0xc22539, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_4B_OPCODES) },
 	{ "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) },
 	{ "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
@@ -1272,11 +1273,12 @@ static const struct flash_info spi_nor_i
 	{ },
 };


Can this be fixed/added to source?

More information can be found at the following URL:
https://bugs.openwrt.org/index.php?do=details&task_id=3438

You are receiving this message because you have requested it from the Flyspray bugtracking system.  If you did not expect this message or don't want to receive mails in future, you can change your notification settings at the URL shown above.